VBMB16R20S
Product Specifications
VBMB16R20S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBMB16R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBMB16R20S: one die, three bodies and a 35 W row that matters
The VBMB16R20S is a 600 V N channel super junction MOSFET rated 0.15 ohm at a 10 V gate, supplied in the TO-220 Fullpak. The same sheet covers three order strings and three bodies: VBM16R20S in TO-220AB, VBMB16R20S in TO-220F and VBP16R20S in TO-247AC. One electrical table serves all three, and that is the first thing a buyer has to understand, because the maximum power dissipation row reads 205 W and 35 W in the same cell.
Which row applies is decided by the body, not by the part number suffix alone. The isolated Fullpak cannot pass the same heat as the exposed tab, so the 35 W figure is the one that belongs to the VBMB string. A purchase order that names only the voltage and the on resistance, without the body, can arrive with a part that has six times less dissipation than the one that was qualified.
The part covers server and telecom supplies, switch mode supplies, power factor correction and lighting. At 600 V and 0.15 ohm it is the middle member of a family that runs from 0.056 ohm at 650 V to 0.38 ohm at 800 V, and its place in the line is the mid power PFC stage and the primary switch of a 150 W to 400 W adapter.
The parameter table in full
| Drain to source voltage at maximum junction temperature | 600 V |
| Gate to source voltage, continuous | plus or minus 30 V |
| On resistance at 10 V gate and 8 A, 25 C | 0.15 ohm typical |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| Continuous drain current, case at 25 C and 100 C | 20 A and 10 A |
| Pulsed drain current, repetitive | 62 A |
| Single pulse avalanche energy, 28.2 mH and 4.5 A start | 485 mJ |
| Maximum power dissipation, case at 25 C | 205 W exposed tab and 35 W isolated tab |
| Linear derating factor | 1.67 W per C |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Operating junction and storage range | minus 55 to plus 150 C |
| Drain source voltage slope, junction at 125 C | 37 V per ns |
| Reverse diode voltage slope | 4.5 V per ns |
| Input, output and reverse transfer capacitance | 1440, 80 and 4 pF |
| Effective output capacitance, energy and time related | 63 and 213 pF |
| Total gate charge, typical and maximum at 10 V | 48 and 96 nC |
| Gate source and gate drain charge | 11 and 21 nC |
| Turn on delay and rise time at 520 V and 8 A | 18 and 24 ns typical, 25 and 55 ns maximum |
| Turn off delay and fall time, same conditions | 48 and 25 ns typical, 70 and 40 ns maximum |
| Gate input resistance | 0.8 ohm |
| Continuous and pulsed source drain diode current | 20 and 60 A |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time, charge and peak current | 475 ns, 5.8 microcoulomb and 35 A |
| Forward transconductance at 8 A | 5.6 S |
| Peak soldering temperature for 10 s | 300 C |
Why the dissipation cell carries two numbers
A 205 W rating at a 25 C case implies a junction to case path of 0.61 C per watt, and the sheet prints 0.7, which is consistent within rounding. The 35 W row cannot come from the same 0.7: 35 W times 0.7 is 24.5 C, so the package would be limited by something other than the silicon. That is exactly what happens in a moulded Fullpak, where the plastic between the die pad and the mounting surface adds a thermal resistance that is not in the silicon table.
The practical consequence is that the isolated body must be qualified on its own heatsink, not borrowed from a reference board built with the TO-220AB. At 20 A through 0.15 ohm the channel sheds 60 W, which is already above the 35 W row, so the continuous rating cannot be taken at face value in this body at all. A 10 A load at the same resistance sheds 15 W, and that fits.
In still air the ambient path is worse than any of these: 62 C per watt allows 2.02 W for a 125 C rise, which is 3.67 A at 25 C. Most boards built with this part carry a heatsink, and the row to quote to a customer is the case temperature at their loss, not the 20 A headline.
Switching, and a summary block that does not match the table
The electrical table gives 48 nC typical and 96 nC maximum of total gate charge at a 10 V gate, 11 nC of gate source charge and 21 nC of gate drain charge. The product summary on page one prints 70 nC as a maximum and 7.8 and 9 nC for the two components. Those two sets cannot both be right, and the difference is not rounding: 96 against 70 is 37 percent. When a driver is sized from the summary and the lot follows the table, the drive current is short and the switching times stretch. We size from the table and treat the summary as a marketing row.
The switching rows themselves are consistent with the charge figures: 18 ns turn on delay and 24 ns rise, 48 ns turn off delay and 25 ns fall at 520 V and 8 A into a 9.1 ohm gate resistor. At 65 kHz the drive power for 96 nC at 10 V is 0.062 W, so a 0.3 A driver has margin.
The diode is slow. 475 ns of recovery with 5.8 microcoulomb and 35 A of peak reverse current at 8 A and 400 V means a hard switched bridge sees a large reverse current spike at every commutation. In a continuous conduction PFC at 65 kHz the diode loss can exceed the conduction loss, and in a bridge the spike lands on the opposite switch. A resonant or quasi resonant stage avoids the problem altogether, which is why the lighting applications on page one fit this part better than a hard switched server stage does.
Where the isolated body wins and where it loses
Three strings, one die. The exposed tab TO-220AB and the TO-247AC take 205 W and are the right choice when the heatsink is the switch's own. The Fullpak takes 35 W and is the right choice when several switches share one heatsink and the assembly has to pass an insulation test, or when a field service cannot be trusted to fit a pad correctly. Both statements are true at the same time, which is why the body has to be on the purchase order.
Against the 650 V VBMB165R42SFD this part gives up 50 V of rating and a factor of 2.7 in on resistance, and it gives up the fast diode: 475 ns against 90 ns. Against the 700 V VBMB17R15SE it is lower in resistance but 900 mV lower in avalanche energy. A replacement study that compares only the voltage and the resistance will miss the diode and the avalanche rows, which are the two that fail in the field.
Our power management cross reference work holds the diode recovery, the gate charge spread and the body against each approved alternate, because those three are what a cross reference on a switch really means.
Questions we answer before a reel is booked
First, the body. Ask for the string, not the family. VBM, VBMB and VBP are the same die in three packages, and the 35 W row belongs to the isolated one. If a drawing calls out a Fullpak footprint, an exposed tab part will not fit and will not pass the hipot that the Fullpak was chosen for.
Second, the avalanche figure. 485 mJ is printed against a 4.5 A start into 28.2 mH, which stores 286 mJ, so the printed energy is above what the stated test can deliver. Do not size a snubber from that row; ask for the test report, or run the repetitive curve.
Third, the second source. A 600 V part at 0.15 ohm in the three lead body is available from several suppliers with very different diode recovery, and a unit that passes a static check can still fail a thermal cycling test if the diode is slower. The lead time work and the verification steps for a drop in replacement both start from the diode and the thermal pair, not from the on resistance alone.