VBM2102M
Product Specifications
VBM2102M
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM2102M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM2102M: a minus 100 V P channel switch in TO-220AB
The VBM2102M is a P channel trench MOSFET rated minus 100 V drain to source with a plus or minus 20 V gate, in the TO-220AB body, with 0.167 ohm at a minus 10 V gate and 0.178 ohm at minus 4.5 V. Continuous drain current is minus 18 A with the case at 25 C and minus 13 A with it at 70 C.
A P channel part is chosen for one reason: it lets a high side load be switched without a charge pump or a floating driver. The gate is pulled below the source by a resistor or a small NPN, and the load sees the full rail with no bootstrapping. The price is on resistance, and here the price is visible: 0.167 ohm is roughly five times what a 100 V N channel part of the same body would show. That trade only makes sense at a few amps, a low duty cycle or a low switching frequency.
The data sheet is a trench document with the usual P channel signature: a threshold between minus 1 V and minus 2.5 V, so the part is on with the gate at source potential minus 2.5 V and fully on by minus 4.5 V, which is what makes a 5 V logic rail usable as a high side control without a driver.
The parameter table
| Drain to source voltage | minus 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, minus 14 A | 0.167 ohm |
| On resistance at minus 4.5 V gate, minus 12 A | 0.178 ohm |
| Gate threshold at 250 microamp | minus 1 V to minus 2.5 V |
| Continuous drain current, case at 25 C and 70 C | minus 18 A and minus 13 A |
| Pulsed drain current at 300 microsecond | minus 100 A |
| Avalanche current and single pulse energy | minus 10 A and 3.1 mJ |
| Power dissipation, case at 25 C at 1 per cent duty | 11.7 W |
| Power dissipation, ambient at 25 C at 1 per cent duty | 1.1 W |
| Junction to case and junction to ambient | 9 and 60 C per watt |
| Operating junction and storage range | minus 55 to plus 150 C |
| Gate body leakage at plus or minus 20 V | plus or minus 250 nA |
| Zero gate voltage drain current at minus 100 V, 125 C | 50 microamp |
| Zero gate voltage drain current at minus 100 V, 150 C | 250 microamp |
| Input, output and reverse transfer capacitance | 1460, 330 and 280 pF |
| Total gate charge, typical and maximum | 67 and 100 nC |
| Gate source and gate drain charge | 13.5 and 14 nC |
| Gate resistance, minimum, typical and maximum | 0.5, 2.5 and 5 ohm |
| Turn on delay and rise time | 10 and 11 ns typical |
| Turn off delay and fall time | 42 and 12 ns typical |
| Body diode forward drop at minus 10 A | minus 0.8 V typical, minus 1.5 V maximum |
| Body diode recovery time and charge | 38 ns and 40 nC |
| Peak reverse recovery current | 2.3 A typical, 3.5 A maximum |
The nine degrees per watt junction to case
Nine C per watt from junction to case is not what a TO-220AB usually prints. The same body in this shipment runs 0.4 to 1.1 C per watt on the N channel parts. A value nine times higher means either the die is small and the attach is thin, or the figure was carried across from a different package. It is the first row to confirm with the supplier before a heatsink is sized, because a heatsink chosen for 0.7 C per watt and used with 9 C per watt will run the junction 100 C hotter than expected at the same dissipation.
Check the printed dissipation against that row. At a 25 C case and a 150 C junction the allowed rise is 125 C, and 125 divided by 9 gives 13.9 W, so 11.7 W is consistent with the pair. The 1.1 W ambient figure is about half of what 125 divided by 60 would allow, which suggests the two dissipation rows were measured at the 1 per cent duty cycle stated in the note rather than continuously. A load switch that stays on is not a 1 per cent duty application, and the continuous limit is the pair, not the row.
In practice a 5 A load through 0.167 ohm dissipates 4.2 W, which with 9 C per watt is a 38 C rise to the case before the heatsink is counted. On a board with a copper pad and no heatsink, 60 C per watt to ambient gives a 250 C rise and the part cannot carry 5 A continuously. This is a 2 A to 3 A switch on a board and an 8 A switch on a heatsink.
Why a 4.5 V gate row matters
Most P channel parts in this class print only the minus 10 V row and leave the 4.5 V behaviour to a curve. This sheet prints both, 0.167 ohm at minus 10 V and 0.178 ohm at minus 4.5 V, and the difference is 6 per cent. That is a small penalty for dropping the gate drive from 10 V to a logic rail, and it means a 3.3 V or 5 V system can drive the part directly through a small NPN without a level shifter.
The threshold of minus 1 V to minus 2.5 V is what makes that safe. At minus 1 V minimum a small leakage or a resistor divider can turn the part partly on, so the gate needs a pull up to the source and a firm pull down path. The 20 V gate rating leaves room for a spike on a 100 V rail, but the part conducts long before the gate reaches 20 V, so the pull up resistor is the real protection.
Gate charge of 67 nC typical and 100 nC maximum at a 5 V drive is 0.05 W at 100 kHz, which no controller will notice. The 280 pF reverse transfer capacitance is high for the body and is the reason the turn off delay is 42 ns against a 12 ns fall: the part spends most of its transition time in the plateau, not in the edge.
What a high side load switch needs from the diode
The body diode of a P channel part conducts when the load is inductive and the switch opens. 38 ns of recovery and 40 nC of charge are small, and the peak reverse current of 2.3 A typical is low, so an inductive load of a few millihenry does not need an external clamp at these currents. A relay coil or a small solenoid is covered. A motor with a large rotor inertia is not, and that belongs on the avalanche row, which is only 3.1 mJ and will not absorb much.
That 3.1 mJ is the smallest avalanche figure in this shipment by two orders of magnitude, which follows from a small die. Any application with a real inductive kick should clamp, because the part will not survive it. A 100 V P channel with a 3.1 mJ rating is a switch, not a clamp.
Where this part earns its place
The listed uses are a power switch, a load switch in high current applications, and a DC to DC converter. In practice it is the reverse polarity and load disconnect part in a 48 V or 72 V system, where the gate can be tied to ground through a resistor and the switch is on whenever the rail is present. In that role the 0.167 ohm at 3 A is 1.5 W, and the thermal pair says a copper pad on a board is enough.
Where the same function has to carry 10 A or more, the N channel route with a charge pump wins on resistance and on heat, and the P channel part is the wrong tool. Our pin to pin cross reference records the gate threshold and the 4.5 V on resistance for P channel swaps, because two parts that match on voltage and package often differ by 40 per cent in the logic level row.
A substitution also has to match the gate pull up and the source connection, since a P channel part is defined by its source rail. The drop in verification checks the pull up value and the body diode direction on the board, and the lead time work starts early on this family because 100 V P channel parts are the first to go short.
Questions before a reel is booked
First, the junction to case figure. Nine C per watt is the row that decides the heatsink, and it does not match the usual value for this body. Ask for a measurement on the qualification sample before the thermal file is closed.
Second, the duty cycle behind the dissipation rows. 11.7 W and 1.1 W carry a 1 per cent duty note, and a load switch that stays on is continuous. Use the thermal pair.
Third, the avalanche. 3.1 mJ will not absorb an inductive kick of any size, so the clamp belongs on the board rather than in the part.