Contact Us

VBM18R12S

Brand: VBsemi
VBsemi VBM18R12S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM18R12S — Discrete & Power Semiconductors | Superb Automation

VBM18R12S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM18R12S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM18R12S: 800 V super junction in TO-220AB

The VBM18R12S is an N channel super junction MOSFET in the TO-220AB body, printed at 800 V drain to source with plus or minus 30 V on the gate. On resistance is 0.37 ohm at a 10 V gate, current is 12 A at a 25 C case and 8 A at 100 C, and the single pulse avalanche energy is 850 mJ. The vendor lists server and telecom power supplies, switch mode supplies, power factor correction, lighting including high intensity discharge and fluorescent ballast, and industrial use.

At 800 V the part sits above the usual 650 V class, which is where a product needs margin for a 480 V three phase rectified bus or a high voltage DC link with a large transient. The trade is resistance: 0.37 ohm at 12 A is a real conduction loss of 5.3 W at the rated current, so this is a part for a few amps continuous at high voltage rather than a high current switch. Its value is in the avalanche rating of 850 mJ and the 160 W dissipation in a body that can be bolted to a heatsink.

Ratings, including the ones that limit the part

Drain to source voltage800 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate0.37 ohm at 4 A
Continuous drain current12 A at 25 C case, 8 A at 100 C case
Pulsed drain current36 A
Single pulse avalanche energy850 mJ, 6 A into 28.2 mH
Power dissipation160 W
Linear derating factor1.67 W per C
Junction to case0.7 C per watt maximum
Junction to ambient62 C per watt maximum
Gate threshold voltage2.5 V minimum, 4.5 V maximum
Total gate charge89 nC typical
Input capacitance1400 pF
Output capacitance, energy related62 pF, 0 to 520 V
Body diode reverse recovery40 ns, 15 V per nanosecond reverse dvdt limit
Drain source dvdt limit50 V per nanosecond

What the rows say about using it well

The on resistance is measured at 4 A, which is a third of the current rating, so 0.37 ohm is a light load figure. At 8 A and a 125 C junction it will be higher, and the loss budget should be written at the hot value rather than the cold one. The compensation is that the part is usually operated at 2 A to 5 A in a power factor correction stage, where 0.37 ohm is 1.5 W to 9 W and a TO-220 heatsink handles it easily.

The threshold window is 2.5 V to 4.5 V, so a 10 V drive is assumed and a 5 V drive is marginal on the worst case device. Gate charge is 89 nC with 1400 pF of input capacitance and a gate resistance of 0.8 ohm, which is a moderate load and gives fast edges. The dvdt limit of 50 V per nanosecond is the constraint that shapes the gate network: at 800 V the whole edge must take at least 16 ns, and a faster edge risks the parasitic bipolar turning on. The reverse diode dvdt limit of 15 V per nanosecond is tighter and applies when the body diode is recovering, which is the classic failure mode of a super junction bridge.

The output capacitance is small, 80 pF at 100 V with 62 pF energy related, which keeps the turn on loss low but makes the drain node ring with any stray inductance. In a 800 V stage the ringing is at hundreds of megahertz and can exceed the 800 V rating even with a 700 V bus, so a clamp or a snubber is not optional. The 850 mJ avalanche rating covers the energy of that ringing to a point, but it is a single pulse at 25 C and it derates quickly with temperature.

The body diode recovery of 40 ns with 15 V per nanosecond reverse dvdt is the number a bridge engineer checks first, because it sets the minimum dead time and the peak current the opposite switch has to absorb. In a phase shifted full bridge or an LLC the diode is not the main conduction path and the recovery is manageable, while in a hard switched bridge at 100 kHz the same recovery produces a current spike that the opposite device has to absorb. The topology choice, not the part, decides whether this die works well.

Where 800 V is needed

A 480 V three phase input rectified gives about 680 V, and an 800 V part leaves margin for a 10 per cent line surge, which is why this class appears in industrial power supplies and in telecom rectifiers with a wide input range. Power factor correction in a 400 V to 480 V system uses it as the boost switch, where 12 A is enough for 2 kW to 3 kW at a reasonable duty. Lighting uses it in the igniter of a high intensity discharge lamp, where the 850 mJ avalanche rating absorbs the strike, and in fluorescent ballast where the 800 V rating covers the lamp strike transient.

Industrial drives with a 600 V DC link use it as a small auxiliary switch, and solar string inverters with a 700 V link use it on the input side. In every case the part is chosen for the voltage margin and the avalanche rating rather than the current, and the heatsink is what turns 160 W of dissipation into a real 5 A switch.

Sourcing an 800 V part and matching the driver

At 800 V the second source question is mostly about the dvdt behaviour and the diode recovery, not about the resistance. Our power management cross reference therefore compares the voltage class, the dvdt limits and the recovery first, and only then the resistance and the gate charge. A part that matches on resistance but rings harder at turn off can destroy itself in a week.

The practical route for a replacement is in how to verify a drop in replacement, and for this voltage it adds a double pulse test at the real bus and a diode recovery measurement with the real di/dt. The gate resistor value in the reference circuit is a starting point, not a specification. We supply this code with the driver and the resistor value we recommend for the edge, and we sample threshold and resistance from each lot through our incoming inspection plan.

Questions buyers ask about this code

Is the part 800 V or 650 V? It is 800 V, and the sheet prints a 0.70 V per C temperature coefficient on the breakdown, which means the rating holds across the range rather than being a cold number. The second question is whether 12 A can be drawn continuously. At a 25 C case and a heatsink, yes, with about 53 W of loss at 12 A on the cold resistance, so in practice the honest continuous current is 5 A to 8 A on a modest heatsink.

The third is the avalanche rating. 850 mJ into 28.2 mH at 6 A is unusually high and covers a lamp strike or a motor turn off, but it is a single pulse at 25 C, and a repetitive event has to be checked against the derating curve. The fourth is the diode: 40 ns recovery is fast for a super junction body, but the reverse dvdt limit of 15 V per nanosecond is the real constraint, and a slow gate resistor helps more than a snubber in many cases.

On supply we quote the reel and the date code and hold a per lot resistance and threshold record. For an 800 V part we also recommend a first article curve trace at the rated voltage on any new date code, because the breakdown margin is the parameter a customer cannot check on a bench supply.