VBM16R41SFD
Product Specifications
VBM16R41SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM16R41SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM16R41SFD: 600 V, 0.062 ohm and a diode built for commutation
The VBM16R41SFD is a 600 V N channel super junction MOSFET in the TO-220AB body with a fast body diode, 0.062 ohm at a 10 V gate and 41 A of continuous drain current with the case at 25 C. The part is aimed at the supplies that sit behind a power factor stage: server and telecom supplies, switch mode supplies, power factor correction, lighting ballast and industrial drives.
The suffix in the part number is the point of the device. A standard super junction body diode is slow, with tens of microcoulomb of recovery charge, and that charge is what limits a bridge or a phase shifted converter. This sheet prints 60 ns of recovery and 5.8 microcoulomb, which is the fast diode family, and it pairs that with the lowest on resistance in this band of the catalogue at 0.062 ohm.
The price of the low resistance is capacitance. 4350 pF of input capacitance is the highest among the ten parts in this shipment, and 57 nC of gate charge is at the upper end. A converter that saves 3 W of conduction loss and then spends it on drive and output capacitance at 200 kHz has not saved anything, so the frequency has to be part of the decision.
The full parameter table
| Drain to source voltage | 600 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 13.5 A, 25 C | 0.062 ohm typical |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Continuous drain current, case at 25 C and 100 C | 41 A and 25 A |
| Pulsed drain current | 120 A |
| Single pulse avalanche energy, 28.2 mH, 21 A start | 1600 mJ |
| Power dissipation, case at 25 C | 230 W |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Linear derating factor | 1.67 W per C |
| Operating junction and storage range | minus 55 to plus 150 C |
| Breakdown voltage temperature coefficient | minus 0.70 V per C |
| Input, output and reverse transfer capacitance | 4350, 80 and 4 pF |
| Effective output capacitance, energy and time related | 62 and 213 pF |
| Total gate charge at 520 V, 8 A | 57 nC |
| Gate source and gate drain charge | 15 and 19 nC |
| Turn on delay and rise time | 18 and 24 ns typical |
| Turn off delay and fall time | 80 and 12 ns typical |
| Gate input resistance | 0.8 ohm typical |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time and charge | 60 ns and 5.8 microcoulomb |
| Body diode peak reverse recovery current | 35 A |
| Continuous source drain diode current | 41 A |
| Drain source voltage slope at 125 C | 50 V per ns |
| Soldering peak temperature for 10 s | 260 C |
What the thermal pair says about the 41 A row
At 41 A through 0.062 ohm the die dissipates 104 W. With 0.7 C per watt from junction to case that is a 73 C rise above the case, so the case has to sit near 77 C for the junction to stay at 150 C. That is a real heatsink, not a copper pour. The 41 A rating is honest for the package, but it is a statement about a case temperature that the customer has to provide.
In still air the same part sees 62 C per watt to ambient, which supports 2.02 W at a 25 C ambient and 1.61 W at 50 C, equal to 5.70 A and 5.10 A through 0.062 ohm. The distance between 41 A and 5.7 A is the whole thermal story in one line, and it is the reason a first article should be measured with a thermocouple on the tab rather than with a finger on the plastic.
The printed dissipation of 230 W is 51 W above the 178.6 W that 0.7 C per watt supports at a 150 C junction with the case at 25 C. The sheet is not wrong to print a package limit, but the two rows cannot both be used as limits. Use the thermal pair and treat the dissipation row as a package capability.
Where a fast diode changes the circuit
In a phase shifted full bridge, the body diode of the switch that is not driving carries the freewheel current before the other switch turns on, and its recovery charge is what the opposite switch has to pull out. 5.8 microcoulomb at 400 V of reverse bias is small enough that a 65 kHz bridge can work without an external Schottky, which is exactly why the fast diode family exists. The 60 ns recovery is the number to put against the competitor's 300 ns standard body.
The peak reverse current of 35 A is the other half of that story. Recovery charge tells you the energy, peak current tells you the current spike that the loop inductance turns into voltage. At 20 nH of loop inductance, 35 A of reverse current is 0.7 V of extra overshoot per nanosecond of transition, which is manageable on a 400 V bus and worth measuring on the first article rather than assuming.
The 50 V per ns drain source slope is the fastest printed in this shipment, and it comes with an 80 ns turn off delay and a 12 ns fall. That combination is hard on EMI. A gate resistor larger than the 9.1 ohm used in the printed conditions will slow the fall and cost switching loss, so the resistor has to be chosen with the filter, not before it.
Choosing between the 600 V and 650 V siblings
A 600 V part on a 400 V bus leaves 50 per cent margin, and 650 V leaves 62 per cent. Both are acceptable for a supply that clamps the bus, and the 650 V part is the safer choice for a bus that can see a mains surge with the load dumping back. The cost of the extra 50 V in this family is about 0.023 ohm and roughly 3 nC of gate charge, which is a small price when the surge is real.
Where the current is under 5 A and the frequency is above 150 kHz, the lower capacitance parts in the band are the better trade, even at higher on resistance, because the switching term dominates. Where the current is above 15 A and the frequency is under 100 kHz, this part and its 0.062 ohm are the right end of the family. Our power management cross reference keeps the capacitance beside the resistance for exactly that comparison.
When a line is short of the original device, the shortage recovery work starts from the diode recovery and the output capacitance, because those two decide whether the substitute survives in the same topology. The first article then goes through the launch checklist with the gate resistor and the dead time recorded, since both change when the part changes.
At 100 kHz and a 400 V bus the output capacitance term becomes visible. The 80 pF output capacitance plus the 62 pF energy related figure the sheet prints for the same purpose is charged and discharged every cycle, and the energy in that capacitance is about 5 microjoule per cycle, which is 0.5 W at 100 kHz and doubles at 200 kHz. That is why the same die that is comfortable at 65 kHz needs a different thermal file at 200 kHz, and why the switching frequency belongs in a quotation next to the current.
Questions we answer before a reel is booked
First, the drive. 57 nC at 10 V and 65 kHz is 0.037 W of drive power, which any controller can supply, but the 4350 pF input capacitance means the driver has to source real current during the rise. A weak driver turns a 24 ns rise into 60 ns and moves the loss from the die to the channel.
Second, the diode. If the topology forces the body diode to conduct, the 5.8 microcoulomb and 35 A peak are the two rows to measure on the first article, at the hot case temperature rather than at 25 C. Recovery charge rises with temperature and the room temperature number understates it.
Third, the avalanche and the surge. 1600 mJ is a single event figure from a 28.2 mH load. A supply with a repetitive surge belongs on the derating factor and on a measured tab temperature, not on that row.