VBM165R32S
Product Specifications
VBM165R32S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM165R32S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM165R32S: a 650 V super junction switch at 0.085 ohm in TO-220
The VBM165R32S is a 650 V N channel super junction MOSFET in the TO-220 body, with 0.085 ohm on resistance at a 10 V gate, 60 nC of total gate charge and 32 A of continuous drain current with the case at 25 C. The application list on page one is the standard one for the class: server and telecom supplies, switch mode supplies, power factor correction, lighting ballast and industrial drives.
What separates a super junction part from a trench part of the same voltage is the shape of the loss curve. The die is built as a charge balanced column, so the on resistance per unit area falls by roughly a factor of four while the capacitance per unit area rises. The 3400 pF input capacitance and the 80 pF output capacitance on this sheet are the visible cost of that trade, and the 60 nC gate charge is the figure that decides whether the driver can be a small one.
Two ratings on page one need reading together: a 1400 mJ single pulse avalanche energy, which is high for the body size, and a 50 V per ns drain source slope, which is the fastest in this band of the catalogue. Both come from the same column structure, and both are why the part is usually seen in a power factor stage rather than in a hard commutated bridge with a slow diode.
Numbers printed on page one and page two
| Drain to source voltage | 650 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 10.5 A, 25 C | 0.085 ohm typical |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Continuous drain current, case at 25 C and 100 C | 32 A and 20 A |
| Pulsed drain current | 96 A |
| Single pulse avalanche energy, 28.2 mH, 16 A start | 1400 mJ |
| Power dissipation, case at 25 C | 190 W |
| Junction to case and junction to ambient | 0.7 and 62 C per watt |
| Linear derating factor | 1.67 W per C |
| Operating junction and storage range | minus 55 to plus 150 C |
| Breakdown voltage temperature coefficient | minus 0.70 V per C |
| Input, output and reverse transfer capacitance | 3400, 80 and 4 pF |
| Effective output capacitance, energy and time related | 62 and 213 pF |
| Total gate charge at 520 V, 8 A | 60 nC |
| Gate source and gate drain charge | 15 and 19 nC |
| Turn on delay and rise time | 18 and 24 ns typical |
| Turn off delay and fall time | 80 and 12 ns typical |
| Gate input resistance | 0.8 ohm typical |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time and charge | 60 ns and 5.8 microcoulomb |
| Body diode peak reverse recovery current | 35 A |
| Drain source voltage slope at 125 C | 50 V per ns |
| Soldering peak temperature for 10 s | 260 C |
One on resistance row and a curve instead of a hot number
Unlike the trench sheets in this band, this document prints a single on resistance row, at 25 C and 10.5 A, and leaves the junction temperature behaviour to Fig. 4, which is the normalised curve against temperature. That has a practical consequence for a buyer: the hot resistance cannot be quoted from the table, because the table does not carry it. It has to be read off the curve, and the curve is a typical, not a limit.
For a first pass the usual super junction slope of about 2.2 to 2.6 times the 25 C value at 125 C puts the part near 0.19 to 0.22 ohm hot. That is my arithmetic on a typical curve, not a printed figure, and it belongs in a file as an estimate with the source written next to it. A project that needs a guaranteed hot number should ask the supplier for the 125 C row in writing rather than accept the estimate.
The thermal pair gives the other end of the calculation. 62 C per watt from junction to ambient supports 2.02 W in still air at a 25 C ambient, which is 4.87 A through 0.085 ohm, and 1.61 W at 50 C, which is 4.36 A. The 32 A row assumes a case held at 25 C, and the 190 W dissipation row sits slightly above what 0.7 C per watt supports at a 150 C junction, which is 178.6 W. Where two printed rows disagree, the thermal pair is the one to use.
What 60 nC costs at 65 kHz
At 10 V of drive and 65 kHz, 60 nC costs 0.039 W, so a driver of a few hundred milliwatts is enough and the gate is not the constraint. The output capacitance is where the switching loss actually sits: 80 pF at 100 V plus the 62 pF energy related figure, charged and discharged every cycle across a 400 V bus, is the term that grows with frequency. At 65 kHz it is small. At 300 kHz it is the reason the part warms up with no load current at all.
The turn off rows are asymmetric, 80 ns delay with a 12 ns fall, which is what a charge balanced column looks like when it is switched off with a 9.1 ohm gate resistor. The turn on side is 18 ns delay and 24 ns rise. A gate resistor copied from a trench part will produce a different current slope and a different EMI signature, so the 9.1 ohm used in the printed conditions is the sensible starting point for a first article.
The avalanche rating is worth understanding rather than quoting. 1400 mJ comes from a 28.2 mH load at a 16 A start, which is a large inductive energy for a TO-220 body and covers most unclamped inductive switching events in a motor or a relay load. It does not cover a repetitive event, and the 1.67 W per C derating still applies.
Where the part fits, and where it does not
A 650 V device in a 400 V bus system carries 62 per cent margin, which is the usual target for a supply that has to survive a mains surge. The 0.085 ohm at 10.5 A gives a 0.9 V drop and 9.4 W at that current, so the part wants either a heatsink or a lower current. In a 1 kW power factor stage running at 65 kHz with 4 A average, the conduction loss is 1.36 W and the thermal path is comfortable on a board with copper. In a 3 kW stage at 16 A, the same part dissipates 21.8 W and needs a real heatsink.
The body diode of 60 ns and 5.8 microcoulomb is fast enough for a bridge, but the 35 A peak reverse current is high for the body, so a bridge using this part should still check the commutation spike on the first article. Where the topology keeps the diode out of conduction, the fast recovery is free margin.
Customers comparing this part with the 0.062 ohm 600 V sibling gain 50 V of rating and lose 0.023 ohm, which at 5 A is 1.5 W against 0.98 W. That is a fair trade on a 400 V bus and a poor one on a 300 V bus. Our pin to pin cross reference records the diode recovery and the gate charge beside the voltage and the resistance, because those are the two rows that decide whether a substitute behaves on the same board.
Questions a buyer asks before approving the part
First, the gate drive. A 2.5 V to 4.5 V threshold will turn on from a 5 V driver but not cleanly at low temperature, and the 3400 pF input capacitance makes a weak driver slow. Use 10 V and check the driver current against 60 nC at the switching frequency.
Second, the hot on resistance. The sheet gives 25 C only, so ask for the 125 C row or accept a curve based estimate in writing. A qualification that tests only at 25 C will pass a lot that fails in a warm enclosure.
Third, the second source. Super junction 650 V parts at 0.085 ohm differ mainly in output capacitance and diode recovery, and two parts that match on voltage and resistance can differ by 2 A of peak reverse current. We check both on the first article and keep the measurement with the drop in verification record, then hold the supplier to it through the supplier audit rather than through the data sheet.