VBM165R09S
Product Specifications
VBM165R09S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM165R09S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM165R09S: a 650 V, 0.5 ohm switch for power factor and lighting
The VBM165R09S is a 650 V N channel MOSFET in the TO-220AB body, printed at 0.5 ohm with a 10 V gate and 4 A, 9 A of continuous drain current with the case at 25 C, and 123 W of dissipation. The application list names server and telecom power supplies, switch mode supplies, power factor correction, high intensity discharge lighting and fluorescent ballasts.
One line on the first page needs to be read with care. The product summary prints the drain to source voltage as 700 V at maximum junction temperature, while the absolute maximum table on the same page prints 650 V. Both numbers can be true if the summary is describing the breakdown voltage at a hot junction and the table is describing the rated maximum, but a buyer who quotes 700 V from the summary will be working outside the rating. Take 650 V as the number to work with.
The ratings a buyer checks first
| Drain to source voltage, absolute maximum | 650 V |
| Drain to source voltage printed in the summary | 700 V at maximum junction temperature |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 4 A | 0.5 ohm typical |
| Continuous drain current with the case at 25 C | 9 A |
| Pulsed drain current | 21 A |
| Single pulse avalanche energy from 28.2 mH | 186 mJ at 3.5 A |
| Dissipation with the case at 25 C | 123 W |
| Linear derating factor | 1.5 W per C |
| Junction to case and junction to ambient | 0.6 and 63 C per watt |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| Gate leakage at plus or minus 20 V and at 30 V | 100 nA and 1 microamp maximum |
| Effective output capacitance, energy related | 45 pF typical |
| Effective output capacitance, time related | 62 pF typical |
| Total gate charge at 520 V, 4 A | 25 nC typical |
| Gate source and gate drain charge | 2.0 and 2.7 nC |
| Turn on delay and rise time | 25 and 55 ns typical |
| Turn off delay and fall time | 70 and 40 ns typical |
| Gate input resistance | 3.5 ohm typical |
| Body diode forward drop at 4 A | 1.5 V maximum |
| Body diode recovery time and charge | 190 ns and 2.3 microcoulomb |
Reading the electrical table instead of the front page
The dynamic section of this sheet is unusual in what it leaves out. The input, output and reverse transfer capacitance cells are printed as dashes, and the only capacitance figures given are the two effective values, 45 pF energy related and 62 pF time related. A buyer who is used to reading 1800 pF of input capacitance for a part like this has to work from the gate charge instead, and 25 nC with a gate drain charge of 2.7 nC is low enough that a light driver will still switch the part quickly. The trade is that the Miller plateau cannot be read off the sheet, so the gate resistor has to be chosen on the bench rather than on paper. The 3.5 ohm internal gate resistance is high for the class, which makes the external resistor less critical, since the internal value already damps most of the ring that a lower resistance part would show.
The two effective capacitance figures differ by 38 per cent, which is the normal spread between the energy and the time definition and is not an error. For a hard switched stage the time related value is the one that sets the turn on loss, and a calculation of half of 62 pF times 380 V squared gives about 4.5 microjoule per cycle, or roughly 0.45 W at 100 kHz. That is a modest number for a 650 V part and it comes from a small die rather than from a clever structure.
The gate leakage row is worth noticing because it is printed twice, at 100 nA for plus or minus 20 V and at 1 microamp for the full plus or minus 30 V. The second figure is ten times the first, which tells you the gate oxide is being pushed at the top of the range. A drive that rings to 30 V is inside the rating and is already an order of magnitude leakier than one that stops at 20 V.
Where a 650 V small die part earns its place
Six hundred and fifty volts is the standard class for a single phase power factor stage in a 100 W to 300 W supply, for the primary switch in a flyback or a two transistor forward running from a 400 V bus, and for high intensity discharge and fluorescent ballasts where the strike voltage needs the headroom. In all of those the current is under 5 A and the 9 A rating at a 25 C case is more than the application needs, which leaves room for the surge.
It is also a sensible part for a lighting driver that has to survive a 1 kV ring wave, because the 650 V rating plus the 30 V gate range plus the 186 mJ avalanche rating covers a mains transient that a 600 V part would not. The body diode recovery of 190 ns with 2.3 microcoulomb is ordinary, so the same rule applies as for any part in this class: fine in discontinuous conduction, careful in a bridge. The 21 A pulsed rating is the row to check on a lighting load, because a strike event that lasts longer than the pulse window is carried by the avalanche path rather than by the current rating.
Sourcing notes and the second source question
Six hundred and fifty volt parts in the 0.4 to 0.6 ohm range are made by every vendor that serves the adapter market, so availability is rarely the problem and equivalence is. Three columns separate a real substitute from a catalogue match: the gate charge, the time related output capacitance and the recovered charge. A candidate with 45 nC of gate charge instead of 25 nC will slow the edge, and a candidate with 6 microcoulomb of recovered charge instead of 2.3 will lose more in the diode than it gains in the switch.
Where an older lighting product is being kept in production, the risk is obsolescence rather than shortage. The obsolete part cross reference hub is the page we start from in that case, and the power management cross reference carries the electrical columns needed to confirm that a proposed replacement will not change the switching behaviour of a circuit that was qualified years ago.
Questions we answer before a reel is booked
First, which voltage the customer is working to. The summary line says 700 V and the rating says 650 V, so a request that quotes 700 V is describing the breakdown at a hot junction rather than the rating. We quote 650 V and say why, and we suggest that a bus above 420 V needs a different part rather than a different reading of the same sheet.
Second, how the gate is driven. With a gate charge of 25 nC and an internal gate resistance of 3.5 ohm, an external resistor of 10 to 22 ohm gives a clean edge without a gate driver larger than the application needs. The 30 V gate rating is wide, and the leakage row makes it clear that running at 30 V costs an order of magnitude of gate current compared with 20 V.
Third, what the first article should measure. On a small die 650 V part the threshold and the on resistance are the two that move, and the avalanche rating of 186 mJ at 3.5 A is a single pulse figure that should not be read as a repetitive one. A flyback with a leakage spike every cycle needs the repetitive curve, not the single pulse line, and that curve is the one to ask the vendor for if a clamp is being removed to save cost. Where the product is a cost reduction on an existing board, the guide to reducing component cost puts the avalanche and the clamp in the same trade rather than treating them separately.