Contact Us

VBM1615A

Brand: VBsemi
VBsemi VBM1615A is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1615A — Discrete & Power Semiconductors | Superb Automation

VBM1615A

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1615A from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1615A: 60 V and 80 A at 9 milliohm

The VBM1615A is a single N channel MOSFET in a TO220 body rated at 60 V drain to source, plus or minus 20 V on the gate, a 2.5 V threshold, 80 A of drain current, 12 milliohm at a 4.5 V gate and 9 milliohm at a 10 V gate. The die is a trench part.

Sixty volts is the class for a 48 V battery, a 36 V pack at the top of charge, a 42 V rail and a 24 V system with a load dump allowance. It sits between the 40 V parts used on 24 V and the 100 V parts used on 72 V, and it is the class that survives a 48 V lead acid string at 58 V.

Nine milliohm at 80 A is 57.6 W. At 40 A it is 14.4 W. At 20 A it is 3.6 W. The tab and the heatsink decide the current, and the two resistance columns decide how much of the loss the drive is responsible for.

Key data for the VBM1615A

ConfigurationSingle N channel
PackageTO220 through hole with a metal tab
VDS60 V
VGSPlus or minus 20 V
Vth2.5 V
ID80 A, a die figure at a 25 C case
RDS(on) at 4.5 V12 milliohm
RDS(on) at 10 V9 milliohm
TechnologyTrench
Loss at 20 A3.6 W at 9 milliohm
Loss at 40 A14.4 W at 9 milliohm
Loss at 80 A57.6 W at 9 milliohm

A quarter more loss on a 5 V drive

The gap between 12 and 9 milliohm is a third of the resistance, so a 4.5 V drive costs a third more conduction loss than a 10 V drive. At 40 A that is 4.8 W more, which on a 14.4 W part is a third more heat for the same current.

The 2.5 V threshold makes the part usable from a 5 V logic output and even from a 3.3 V rail at reduced current, which is what makes it popular in a system with only logic rails available. The published resistance at those voltages is not printed, so a product that relies on it needs the curve.

The 20 V gate window is standard and it is comfortable for a 10 V drive. At 60 V the drain to gate capacitance is smaller than at 400 V, so the Miller turn on is less of a hazard, but a fast turn off at 40 A still couples enough current into the gate to need a solid pull down.

Sixty volts on a 48 V lead acid string.

A 48 V lead acid string reaches 58 V at the top of charge and higher during an equalisation step, which is why the 60 V class exists at all. A 100 V part would be safer and has more resistance for the same die area, so the 60 V class is the last one that covers the string without a large penalty.

During an equalisation step the string can reach 62 V, which is past the 60 V rating. That is the case where the charger has to be built around the part, or the part has to be a 75 V or 100 V device. The voltage has to be checked against the charging profile, not against the label on the pack.

A 36 V pack at 43.2 V has 17 V of margin, which is comfortable. A 42 V rail has 18 V. Those are the easy cases and they are where most of these parts are used, in a motor drive or a DC to DC converter fed from a 36 V or 42 V battery.

Heatsink arithmetic at nine milliohm

At 20 A the loss is 3.6 W, which the tab alone removes in still air on a reasonable copper area. At 40 A it is 14.4 W and a small clip on heatsink holds it. At 60 A it is 32 W and the part needs a real heatsink with airflow, at which point a larger package or two devices in parallel are the better answer.

The tab is the drain at 60 V, which is low enough that an insulator is often skipped on a low voltage product. That is a decision for the safety analysis rather than for the thermal one, because a shared heatsink at 60 V is still a live surface.

The source path matters at 40 A. The two source leads carry half the current each, and their combined resistance and inductance are part of the loop. A pour on both sides of the board with the leads through it halves both, and the difference shows up as a smaller drain spike as much as a lower loss.

Where the part fits and where it does not

It fits a 48 V motor drive at 20 to 40 A, a 36 V battery disconnect, a synchronous rectifier on a 12 V output supplied from 48 V, a 42 V power tool controller and a 48 V hot swap path. It does not fit a 60 V equalisation charge, a 72 V pack, or a load near 80 A without a heatsink.

For a 48 V board the questions are the top of charge voltage, the drive rail and the order that keeps the build supplied. Our purchase order follow up page covers how the schedule on a part like this is tracked after the order is placed.

The sourcing side of this part is covered on the kitting service. For a group of parts that has to arrive together, that page covers how the kit is built and checked.

Questions we get on this code

Is a 5 V drive enough? Yes, at 12 milliohm instead of 9. That is a third more loss, which matters at 40 A and does not at 10 A.

Does 60 V cover a 48 V pack? At 58 V top of charge, yes. During an equalisation step at 62 V, no. Check the charging profile.

How much current continuously? On the tab alone 15 to 20 A. With a clip on heatsink 35 to 45 A. At 80 A the loss is 57.6 W and the package is out of its depth.

What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.