VBM15R07S
Product Specifications
VBM15R07S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM15R07S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM15R07S: a 500 V, 0.55 ohm family that spans four bodies
The VBM15R07S is one 500 V N channel die offered in four packages: the TO-251, the TO-220AB, the TO-220 full pack and the TO-252. The printed figures are 0.55 ohm at a 10 V gate and 4 A, 7 A of continuous drain current with the case at 25 C, 60 W of dissipation, and a plus or minus 30 V gate which is wider than most parts in this class.
The family arrangement is the first thing a buyer has to deal with. One data sheet covers four order codes, one thermal table covers four bodies, and the thermal numbers printed are the best of the four. A customer who specifies the isolated full pack body and expects the 2.1 C per watt junction to case on the sheet is going to have a warmer part than the arithmetic suggests. The same applies to the 1423 pF of input capacitance, which is printed once for the family and belongs to one body rather than to four.
The ratings a buyer checks first
| Drain to source voltage | 500 V |
| Gate to source voltage | plus or minus 30 V |
| Packages covered by the document | TO-251, TO-220AB, TO-220 full pack, TO-252 |
| On resistance at 10 V gate, 4 A | 0.55 ohm typical |
| Continuous drain current, case at 25 C and 100 C | 7 A and 4.2 A |
| Pulsed drain current | 44 A |
| Single pulse avalanche energy from 4.5 mH | 275 mJ at 11 A |
| Repetitive avalanche current and energy | 11 A and 6.0 mJ |
| Dissipation with the case at 25 C | 60 W |
| Linear derating factor | 0.48 W per C |
| Junction to case and junction to ambient | 2.1 and 65 C per watt |
| Gate threshold at 250 microamp | 2.0 V minimum, 4.0 V maximum |
| Forward transconductance at 6.6 A | 6.1 S minimum |
| Input capacitance at 25 V | 1423 pF typical |
| Output capacitance at 25 V and at 400 V | 208 and 55 pF |
| Reverse transfer capacitance | 8.1 pF typical |
| Effective output capacitance from 0 to 400 V | 97 pF typical |
| Total gate charge at 400 V, 11 A | 52 nC maximum |
| Gate source and gate drain charge | 13 and 18 nC |
| Turn on delay and rise time | 14 and 35 ns typical |
| Turn off delay and fall time | 32 and 28 ns typical |
| Body diode forward drop at 11 A | 1.5 V maximum |
| Body diode recovery time and charge | 510 ns typical, 770 ns maximum, 3.4 to 5.1 microcoulomb |
Reading the electrical table instead of the front page
Seventy amperes is a headline that no one should plan around. Seven amps with the case at 25 C becomes 4.2 A with the case at 100 C, and the dissipation table stops at 60 W with a 0.48 W per degree derating, so at a 100 C case the part is allowed about 22 W. Through 0.55 ohm that is 4.2 A, which is the same answer the current row gives. The two rows are consistent, which is a good sign in a family sheet, since inconsistent rows are common.
The capacitances tell a more interesting story. Output capacitance is 2000 pF at 1 V and 55 pF at 400 V, and the effective value that matters for switching loss over the whole swing is 97 pF. That large ratio is the classic signature of a planar high voltage die, and it means the switching loss depends heavily on where in the cycle the voltage sits. Using the 208 pF at 25 V overestimates the turn on loss by a factor of two, and one that uses the 97 pF effective value will get close. The 8.1 pF of reverse transfer capacitance is low for a 500 V die, and it is what keeps the drain node from feeding back into the gate at a few hundred volts.
The body diode is slow. A recovery time of 510 ns typical and 770 ns maximum with 3.4 to 5.1 microcoulomb of recovered charge is a diode for discontinuous conduction, not for a bridge. In a flyback or a discontinuous boost the diode does not conduct before the switch turns on, so the figure never appears. In a bridge, or in a continuous mode stage with a synchronous rectifier, it would dominate the loss budget.
Where a 500 V small die part earns its place
The natural uses are auxiliary and standby supplies in a mains powered product, off line chargers below 65 W, LED drivers, small power factor stages and relay replacement in appliances. In each of those the current is a few amps, the switching frequency is moderate, and the part runs in discontinuous conduction, which is exactly where a 500 V planar die with a slow diode behaves well and where the 60 W dissipation limit is not a constraint.
The four packages are chosen by the assembly rather than by the electricals. The TO-251 and TO-252 are surface mount bodies for a board that is reflowed, the TO-220AB is the bolted tab for a heatsink, and the full pack is the isolated tab for a heatsink that is connected to a live rail or to a chassis that must not carry the drain. A product family that uses both a bolted and an isolated body can keep one die and two order codes, which is often cheaper than qualifying two parts. The catch is that the thermal table stays the same and the full pack body does not reach 2.1 C per watt, so a part count saving can turn into a heatsink change.
Sourcing notes and the second source question
Because one document covers four order codes, the purchase order has to name the package and not just the die. A substitute quoted against the TO-220AB string will not fit a board that was laid out for the TO-252, and the on resistance is the same in both, which is how the mistake passes review. The pin to pin cross reference page starts from the package and the pad geometry before it compares any electrical row.
The second point is the material note. The sheet states that lead containing terminations are not RoHS compliant and that exemptions may apply, which is a sentence to keep in the file for a product that ships into Europe. Where a kit is assembled from several sources, the kitting service page describes how the parts for one build are consolidated and labelled so that a mixed lot of packages does not end up on the same line. The material note also makes a leaded termination a deliberate choice for a socket or a high temperature assembly rather than an accident. Where a programme needs a repeatable second source for one of the four bodies, the supplier scorecard is how we keep the two vendors comparable.
Questions we answer before a reel is booked
First, which body. The thermal table on the sheet is one table for four packages and the numbers are the best of them. The isolated full pack has a higher junction to case in practice because the isolation layer sits in the path, so a 60 W figure taken from the sheet and applied to a full pack body will run hot. We ask for the package before quoting a continuous current.
Second, what the gate drive is. A plus or minus 30 V gate is wide and forgiving, and the threshold window of 2 V to 4 V means a 10 V drive is comfortable. The gate charge maximum of 52 nC is low enough that a small driver with a 10 ohm resistor works, and the switching times printed were taken with 9.1 ohm, so a faster edge is available if the board can take it.
Third, whether an avalanche event is repetitive. The single pulse rating of 275 mJ is large, and the repetitive rating is 6.0 mJ per event at 11 A, which is a much smaller number. A snubber that absorbs most of the leakage energy on every cycle is worth more than a large single pulse rating, and the difference between the two rows is where most of the field failures on a flyback come from.