Contact Us

VBM1403

Brand: VBsemi
VBsemi VBM1403 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1403 — Discrete & Power Semiconductors | Superb Automation

VBM1403

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1403 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1403: a 40 V, 3 milliohm switch with a 110 A package limit

The VBM1403 is a 40 V N channel trench MOSFET in the TO-220AB body, printed at 3 milliohm with a 10 V gate and 30 A flowing, 160 A of continuous drain current with the case at 25 C, and a 150 C junction. It is screened 100 per cent for gate resistance and for unclamped inductive switching.

The 160 A number is a calculated die figure and the sheet says so in a footnote: the package limitation current is 110 A. That footnote is the most useful line on the page, because it separates what the silicon can do from what three leads and a tab can carry, and every current quoted above it belongs to a hypothetical assembly with an ideal case temperature.

The ratings a buyer checks first

Drain to source voltage40 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 30 A3 milliohm typical
On resistance at 4.5 V gate, 20 A15 milliohm typical
Continuous current, case at 25 C and 70 C160 A calculated and 140 A
Continuous current, ambient at 25 C and 70 C29 A and 23 A
Package limitation current110 A
Pulsed drain current350 A
Avalanche current and single pulse energy80 A and 320 mJ
Diode continuous current, case at 25 C110 A
Dissipation, case at 25 C and 70 C312 W and 200 W
Dissipation, ambient at 25 C and 70 C3.13 W and 2.0 W
Junction to ambient, typical and maximum32 and 40 C per watt
Junction to case, typical and maximum0.33 and 0.4 C per watt
Gate threshold at 250 microamp2.0 V minimum, 4.0 V maximum
Threshold temperature coefficientminus 8 mV per C
Input, output and reverse transfer capacitance5500, 650 and 450 pF
Total gate charge at 20 V, 20 A120 nC typical
Gate source and gate drain charge30 and 16 nC
Switching at a 10 V gate, turn off delay and fall77 and 10 ns typical
Switching at a 4.5 V gate, turn off delay and fall180 and 60 ns typical
Body diode forward drop at 20 A0.8 V typical, 1.2 V maximum
Body diode recovery time and charge50 ns and 70 nanocoulomb

Reading the electrical table instead of the front page

Start with the two gate voltages. The part is 3 milliohm at 10 V and 15 milliohm at 4.5 V, which is five times worse, and the sheet prints two complete switching tables to match. Turn off delay is 77 ns at a 10 V gate and 180 ns at 4.5 V, and the fall time goes from 10 ns to 60 ns. A board laid out for the 10 V figures behaves like a different circuit on a 4.5 V driver, and conduction loss multiplies by five while the switching loss also rises. There is no reading of this sheet in which a 4.5 V gate is a minor detail. The threshold window of 2 V to 4 V makes the same point from the other side: at 4.5 V of drive a worst case part has half a volt of overdrive and a best case part has two and a half, so one part number covers a comfortable switch and a marginal one.

Then take the current rows in order. The 160 A figure is calculated from the maximum junction temperature and is capped by the 110 A package limit. Two hundred watts of dissipation at a 70 C case is a real number for a bolted tab, and 29 A in free air is the same die on the same board with no heatsink. At 3 milliohm, 110 A makes 36 W, and 160 A would make 77 W. Both are inside the 312 W case rating and both depend entirely on what the tab is attached to.

One more figure is worth noting for a bridge: recovered charge of 70 nanocoulomb with a 50 ns recovery time is a fast diode for a 40 V part. The reverse recovery fall and rise times are printed as 30 ns and 20 ns, which means the recovery is short and reasonably soft, and a synchronous buck at a few hundred kilohertz can rely on it without a parallel Schottky.

Where a 40 V part earns its place

Forty volts is the working voltage of a 24 V rail with margin and of a 12 V rail with a lot of margin, which is why this class dominates synchronous rectification in server and telecom DC to DC converters, battery disconnect switches, OR-ing diodes in redundant supplies, and 24 V motor drives for pumps and fans. The 3 milliohm die is aimed at the low voltage output stage of a converter running at 20 A to 60 A per phase, where conduction loss is the largest single term in the budget.

The second home is a battery powered product with a 24 V pack, where two of these in a half bridge drive a brushed motor and the 320 mJ avalanche rating absorbs the inductive kick at the end of a stall. The body diode is good enough that the freewheel interval does not need a separate device at low frequency, and the 110 A package limit is still far above what a 24 V tool or a small vehicle needs.

Sourcing notes and the second source question

Forty volt parts in the 2 to 5 milliohm range are the most competitive segment in power discretes, so a cross reference is easy to find and easy to get wrong. The trap is a candidate that matches the 10 V resistance and doubles it at 4.5 V, or one that matches both and carries a 2.5 times larger gate charge. The pin to pin cross reference page lists the four columns that decide whether a substitute works in an existing board: gate voltage used on the board, hot resistance, gate charge, and junction to case for the pad that is already there.

Because the segment is crowded, the commercial side is usually about allocation rather than availability. When a specific part number is short, the power management cross reference page is where we start, and the guide to reducing component cost describes the other lever, which is consolidating two similar 40 V parts on one bill of materials into a single part number so the annual quantity earns a better price.

Questions we answer before a reel is booked

The first question is which gate voltage the board actually uses. If the answer is 10 V, the sheet is straightforward. If it is 4.5 V, the resistance is five times higher, the switching is slower, and the same copper that was comfortable at 3 milliohm is now dissipating five times the power. We ask for the driver before quoting a current, and we quote the 4.5 V column when that is the answer.

The second question is the heatsink. The 312 W case figure is not reachable on a board; the real working number is the 110 A package limit and the 3.13 W free air figure, which puts the part at roughly 32 A with no airflow at all. Any project that needs more than that has to show us the tab, the copper area and the airflow, and the answer changes with each of them.

The third question is protection. The gate threshold moves down by 8 mV per degree, so a hot part turns on earlier than a cold one, and the 320 mJ avalanche rating is generous enough that many boards skip a clamp. It is not generous enough to absorb a repeated inductive event at high current, so a motor or a relay load should still be checked against the repetitive avalanche curve before the product is signed off. The 320 mJ figure belongs to a single event at 80 A, and the derating curve takes it down quickly as the case temperature rises.