Contact Us

VBM1103

Brand: VBsemi
VBsemi VBM1103 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1103 — Discrete & Power Semiconductors | Superb Automation

VBM1103

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1103: a 100 V, 3 milliohm N channel die in a three lead body

The VBM1103 is a 100 V N channel trench MOSFET in the TO-220 body, printed at 0.0030 ohm with a 10 V gate and 20 A flowing, 180 A of continuous drain current with the case at 25 C, and a 175 C junction. The sheet states 100 per cent gate resistance and unclamped inductive switching testing, and carries an AEC-Q101 line in the feature list.

The AEC-Q101 line is worth reading twice. The footnote under it reads parametric verification ongoing, which is a different statement from a qualification report on file. For an industrial programme that sentence changes nothing. For an automotive programme it is the first thing a supplier quality engineer will ask about, and the answer has to be a document rather than a feature bullet.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 20 A, 25 C0.0030 ohm typical
On resistance at 10 V gate, 20 A, 125 C0.0064 ohm typical
On resistance at 10 V gate, 20 A, 175 C0.0080 ohm typical
Continuous drain current, case at 25 C and 125 C180 A and 140 A
Continuous source current through the diode180 A
Pulsed drain current and pulsed diode current480 A
Avalanche current and single pulse energy73 A and 266 mJ
Dissipation, case at 25 C and 125 C250 W and 83 W
Junction to case and junction to ambient0.6 and 40 C per watt
Gate threshold at 250 microamp2.5 V minimum, 3.0 typical, 3.5 maximum
On state drain current at 10 V gate120 A minimum
Forward transconductance at 20 A82 S typical
Input capacitance, typical and maximum5780 and 7230 pF
Output capacitance, typical and maximum3070 and 3840 pF
Reverse transfer capacitance, typical and maximum305 and 385 pF
Total gate charge at 50 V, 70 A125 nC typical, 190 nC maximum
Gate source and gate drain charge28 and 46 nC
Gate resistance1.6 minimum, 3.3 typical, 5 maximum
Turn on delay and rise time16 and 110 ns typical
Turn off delay and fall time40 and 12 ns typical
Body diode forward drop at 100 A0.9 V typical, 1.5 V maximum

Reading the electrical table instead of the front page

Three milliohms is a genuinely low figure and it is quoted at 20 A, which is a fifth of the headline current. The hot rows tell the rest of the story: 0.0064 ohm at 125 C and 0.0080 ohm at 175 C, so the die more than doubles its resistance between the test bench and a warm heatsink. At 180 A the cold row implies about 97 W of conduction loss and the 175 C row implies about 259 W, which is already above the 250 W the package is allowed to dissipate with the case at 25 C.

The current and dissipation rows do not quite agree with each other either. A 140 A row at a 125 C case means about 125 W of conduction loss at 0.0064 ohm, while the dissipation table allows 83 W at that same case temperature. The two cannot both hold with one thermal path. Taking the dissipation row as the binding one, the part carries roughly 114 A at a 125 C case, and that is the number to put in a thermal budget rather than the 180 A on the first page.

The gate charge deserves its own line. The typical figure is 125 nC and the maximum is 190 nC, a 52 per cent spread on the same part number. A driver sized on the typical will run out of current on a hot lot at high frequency, and the switching times printed on the sheet were taken with a 1 ohm gate resistor that most boards do not have room for.

Where a 100 V, 3 milliohm part earns its place

This class sits in 48 V battery systems, in synchronous rectification on the secondary of an isolated converter, and in battery disconnect and reverse polarity switching where the switch carries the whole load current. It also suits a 24 V or 48 V DC to AC inverter, where a pair of these in parallel gets the conduction loss low enough that the heatsink stops being the largest mechanical part in the product.

The limit is the body. Three leads and a tab can pass 180 A only with the case held near 25 C by a real heatsink, and the same part in free air is a device of tens of amps. Where a product needs 180 A continuously with no airflow, the answer is four parts in parallel or a different package, not a bigger number on the front page. The 0.0030 ohm die also makes track distance matter: a few centimetres of track at these currents costs more resistance than the difference between two competing parts. Paralleling two of these dies is the usual next step and it buys less than the arithmetic suggests, since two parts at 90 A each still make about 52 W per device at the 125 C row, which is 104 W of heat to remove from the same copper area.

Sourcing notes and the second source question

For an automotive or a high reliability programme the AEC-Q101 sentence is the whole discussion. Ask for the parametric verification report, the test plan and the date, and treat the feature bullet as a claim until that report arrives. Our supplier quality audit page lists the documents we collect for a qualified discrete and the order we ask for them, which is usually faster than a questionnaire round trip. The same list applies to a plastic body with a metal tab, with the die attach inspection report and the wire bond pull data added to it.

On the commercial side, a 100 V 3 milliohm part is available from several vendors with slightly different gate charge and thermal data, so a drop in replacement is usually possible in electrical terms and not always in thermal terms. The guide to verifying a drop in replacement walks through the four checks that catch the failures: threshold window, hot on resistance, gate charge against the driver, and junction to case against the existing heatsink pad.

Questions we answer before a reel is booked

First, what is the gate drive. The threshold maximum of 3.5 V makes a 10 V drive comfortable and a 5 V drive marginal, and no on resistance row is printed below 10 V. A logic level driver that reaches 4.5 V will switch the part into a region the sheet does not describe.

Second, what holds the case. The 0.6 C per watt junction to case figure is a die attach and copper figure, not a board figure. At 100 A and 125 C the part makes about 64 W, so the tab has to sit on something that removes 64 W at a temperature the customer can live with. We ask for the heatsink or the copper area before agreeing a continuous current, because the same die is a 180 A part on one assembly and a 35 A part on another.

Third, what the first article measures. On this part the parameters that move between lots are the threshold, the on resistance at 10 V and the gate charge maximum, so the sample plan should cover all three rather than resistance alone. Avalanche is tested at 266 mJ per the sheet, which is large for this class and is one of the reasons the part is used on inductive loads without an external clamp. The gate resistance window runs from 1.6 to 5 ohm, wide enough that two lots can switch at different speeds with the same external resistor, so the gate waveform belongs on the first article report as well. Our incoming inspection plan lists the measurements that go with it.