VBL7402
Product Specifications
VBL7402
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL7402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL7402: 200 A at 40 V in a seven lead TO-263
The VBL7402 is an N channel MOSFET in the seven lead TO-263 body, printed at 40 V drain to source with plus or minus 20 V on the gate and a 175 C junction limit. On resistance is 1 milliohm at a 10 V gate in the product summary and 1.5 milliohm in the electrical table, with 200 A at a 25 C case and 192 A at 125 C. The seven lead body exists for one reason: the extra source leads halve the source inductance and spread the current, so a 200 A part can be switched without the source bounce that turns a simple gate drive into an oscillator.
Package dissipation is 375 W at a 25 C case and 125 W at 125 C, with 0.4 C per watt junction to case and 40 C per watt junction to ambient on a one inch board. That ambient figure is the one that matters in a real product: at 40 C per watt, a 30 W loss puts the junction 1200 C above ambient, which is impossible, so the part only reaches its current rating when the tab is bolted to something or the copper area is very large. This is the same story as every 40 V part in a power body, and it is worth stating plainly because the 200 A headline is a case temperature number.
Ratings and the rows behind them
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance, summary | 1.0 milliohm at 10 V gate |
| On resistance, table | 1.5 milliohm at 30 A, 25 C |
| On resistance at 125 C | 2.8 milliohm at 30 A |
| On resistance at 175 C | 3.4 milliohm at 30 A |
| Continuous drain current | 200 A at 25 C case, 192 A at 125 C case |
| Continuous source current, diode | 200 A |
| Pulsed drain current, 300 microsecond | 600 A |
| Single pulse avalanche energy | 361 mJ into 0.1 mH, 85 A |
| Power dissipation | 375 W at 25 C case, 125 W at 125 C case |
| Junction to case | 0.4 C per watt |
| Gate threshold voltage | 2.5 V minimum, 3.0 V typical, 3.5 V maximum |
| Total gate charge | 206 nC typical, 310 nC maximum |
| Input capacitance | 13,880 pF typical, 17,350 pF maximum |
| Body diode forward voltage | 0.86 V at 80 A, 1.5 V maximum |
A summary row and a table row that do not match
The product summary prints 1.0 milliohm and the electrical table prints 1.5 milliohm at 30 A and 25 C. Both are on the same sheet, four pages apart. The honest reading is that 1.0 is a best case die figure and 1.5 is the measurement at a stated current and temperature, and a buyer who budgets from 1.0 will be 50 per cent optimistic before the junction even warms. At 100 A the difference is 10 W against 15 W in one device, which is the difference between a fan and no fan in a small enclosure.
The temperature coefficient is also steeper than the headline suggests: 1.5 milliohm at 25 C, 2.8 at 125 C and 3.4 at 175 C, which is 1.9 and 2.3 times. At 100 A the loss at 175 C is 34 W per device, so a parallel pair is the sensible arrangement well before the 200 A rating is reached. The good news is that the 175 C junction limit and the 0.4 C per watt path mean that a properly heat sinked part can run hot without failing, but the loss budget has to be written at the hot resistance, not the cold one.
Gate charge is 206 nC typical and 310 nC maximum with 13,880 pF of input capacitance. That is a large gate load, and the driver has to deliver roughly 31 mA of average current at 100 kHz at the maximum figure, with several amps during the edge. The gate resistance of 0.25 to 1.8 ohm is low, so the external resistor and the driver set the edge rate, and the gate loop has to be short and tight or the part will ring. The switching times in the sheet, 26 ns turn on delay, 21 ns rise, 68 ns turn off delay and 12 ns fall, are measured with a 1 ohm gate resistor at 120 A, which is a realistic test for a motor or a converter at this current.
One note on the sheet is worth passing to any customer: the electrical table carries the note that parametric verification is ongoing. That is a vendor statement about the data set, not a defect in the part, but it does mean the numbers should be confirmed on a sample before a high volume build is committed. We say so rather than pretend the page is final, and we sample resistance and threshold from each lot for exactly this reason.
Where 200 A at 40 V is used
Battery disconnect on a 24 V pack, the low side of a high current synchronous buck, and the pass element of a reverse polarity or ORing stage are the three common positions. Motor drives for small traction, pumps and power tools use the part where the 600 A pulse covers the stall, and the seven lead body suits a driver that has to switch at 20 kHz or more without the source inductance spoiling the gate waveform. Server power supplies use several in parallel on a 50 A to 100 A rail, where the seven lead body also spreads the current between leads and reduces the joint temperature.
At 1.5 milliohm the part is also a candidate for a load switch on a 12 V bus, with the caveat that the body diode conducts in the blocking direction and the forward drop at 100 A is around 0.9 V. A back to back pair solves the blocking problem and doubles the resistance, which is still only 3 milliohm and often cheaper than a dedicated ideal diode controller. In each case the seven lead pad needs the full copper area the sheet assumes, and the solder void rate under the tab is the parameter that decides whether the part meets its thermal figure.
Buying a seven lead TO-263 part
The seven lead TO-263 pad is shared with several other parts at 30 V and 40 V, but the lead pitch and the tab dimensions differ between vendors, so a substitution needs the drawing rather than the name. Our power management cross reference puts resistance at 4.5 V, gate charge, threshold window and avalanche energy side by side, because those four decide whether a drop in part will survive the same switching node at the same frequency.
For a qualified product the replacement test route is in how to verify a drop in replacement, and for a 200 A part it adds a step that low current parts do not need: a thermal soak at the real current with the tab instrumented, plus a void inspection after reflow. We keep an incoming inspection plan for this family that samples on resistance at 10 V and threshold from every lot, and we report the date code with the shipment.
Questions buyers ask on this code
Is 200 A continuous? Only at a 25 C case with the tab held there. In free air with a one inch board the same part is limited to a few tens of amps by the 40 C per watt path, and the honest answer is that 200 A needs a heatsink or several devices. The second question is whether the seven lead body can be replaced by a standard three lead part. Electrically it can, but the source inductance rises and the gate waveform changes, so the driver and the gate resistor have to be revisited rather than reused.
The third question is about gate drive. With 310 nC maximum the part needs a real driver, not a logic pin, and the 13,880 pF input capacitance means the driver has to source several amps during the edge. The fourth is the avalanche rating: 361 mJ into 0.1 mH at 85 A is generous and will absorb a motor turn off, but it is a single pulse at 25 C and it derates with temperature, so a clamp remains the cheaper option on a hot board.
On supply we quote the reel with the date code, and we hold the lot record including the resistance sample. Because the vendor sheet itself marks parametric verification as ongoing, we recommend a first article check on any new date code before a production run, and we can supply that sample from the same lot as the build.