VBL2201K
Product Specifications
VBL2201K
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL2201K from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL2201K: a 200 V P channel switch in the TO-263 body
The VBL2201K is a P channel MOSFET printed at minus 200 V from drain to source with a plus or minus 30 V gate, in the TO-263 outline. The summary gives 1.8 ohm at a minus 10 V gate with minus 2 A flowing, a continuous drain current of minus 4 A with the case at 25 C and minus 2 A with the case at 100 C, a pulsed rating of minus 8 A, a single pulse avalanche energy of 400 mJ and a repetitive avalanche rating of 10 mJ at minus 3 A. The junction is rated to 150 C, and the vendor lists a dynamic dV/dt rating, repetitive avalanche, fast switching and ease of paralleling as the features.
A 200 V P channel is a specialised part. Above about 100 V the P channel cell loses to the N channel on resistance by a wide margin, and 1.8 ohm at 200 V is an order of magnitude worse than a 200 V N channel of the same die area. The part still has a place wherever a high side switch has to work without a floating driver, a charge pump or a transformer, and the 400 mJ avalanche rating makes it usable on an inductive load that switches off hard.
The ratings a buyer checks first
| Drain to source voltage | minus 200 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at minus 10 V gate, minus 2 A | 1.8 ohm typical |
| Continuous drain current, case at 25 C and 100 C | minus 4 A and minus 2 A |
| Pulsed drain current | minus 8 A |
| Single pulse avalanche energy | 400 mJ |
| Repetitive avalanche current and energy | minus 3 A and 10 mJ |
| Maximum power dissipation, case at 25 C | 105 W |
| Junction to case, junction to ambient | 1.0 and 62 C per watt |
| Gate threshold at minus 250 microamp | minus 3 V typical |
| Zero gate drain current at minus 200 V | minus 100 microamp maximum |
| Total gate charge at minus 160 V and minus 2 A | 20 nC maximum |
| Gate source and gate drain charge | 7.1 and 10 nC maximum |
| Input, output and reverse transfer capacitance | 320, 370 and 81 pF |
| Turn on delay and rise time | 14 and 43 ns typical |
| Turn off delay and fall time | 39 and 38 ns typical |
| Body diode forward drop at minus 2 A | minus 5 V maximum |
| Body diode reverse recovery time and charge | 20 ns and 0.5 microcoulomb typical |
| Peak diode recovery dV/dt | minus 5 V per nanosecond |
| Operating junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The current ratings are small and the resistance is large, so the loss arithmetic is easy. At minus 2 A the channel dissipates 7.2 W, and at minus 4 A it dissipates 29 W. With a 1.0 C per watt junction to case the die runs 29 C above the tab at 4 A, which is workable with a sink and impossible on a bare board at 62 C per watt. The realistic board current at a 100 C rise is around 1.2 A, where the loss is 2.6 W.
The output capacitance of 370 pF is larger than the input capacitance of 320 pF, which is unusual and is a property of a P channel cell at this voltage: the die has a large area to reach 1.8 ohm, and the capacitance follows the area. In a high side switch that is turned on once and left on, the capacitance costs nothing; in a switching converter it is the turn on loss, and at 100 V and 50 kHz that is about 90 mW.
The gate charge is modest at 20 nC total with 10 nC in the gate drain region, so a resistor divider from the 200 V rail to the gate, with a zener clamp, is enough to drive the part. That is the whole economic argument for a P channel at this voltage: no isolated supply, no bootstrap, no charge pump. The price is 1.8 ohm, and a buyer should compare that against the cost of the driver circuit an N channel would need.
The body diode forward drop is printed as a maximum of minus 5 V at minus 2 A, which is high even for a P channel body diode and reflects the low current test point. In a circuit where the diode conducts, for example during the dead time of a bridge, the loss will be significant, and the 20 ns recovery suggests a fast but resistive diode. The part is better used as a switch than as a rectifier.
Where a 200 V P channel part earns its place
The first use is reverse polarity protection on a 110 V or 150 V DC bus, where the P channel sits in the positive rail with the gate held below the source by a resistor and a zener. The 200 V rating gives margin over a 150 V bus, and the 400 mJ avalanche rating covers the inductive kick of the load when the input is interrupted.
The second use is a high side switch on a 100 V to 150 V battery or capacitor bank, where the switch has to be on continuously and the current is below 2 A. The 1.8 ohm resistance is the price of not having a floating driver, and at 1 A it is 1.8 W, which needs a small sink but no isolated supply.
The third use is an inrush limiter on a high voltage capacitor bank, where the part is used in its linear region for a short interval and then turned fully on. The 105 W dissipation rating and the 150 C junction give a workable window for a few hundred milliseconds, and the 10 mJ repetitive rating is not the limit because the event happens once per power up.
Sourcing notes and the second source question
A 200 V P channel is close to the end of the P channel roadmap and the number of vendors is small, so a second source is a long term question rather than a short one. Two parts that both print 1.8 ohm at minus 10 V can differ by a factor of two in the avalanche rating, and on a bus where the load is inductive the avalanche rating is the parameter that decides survival. The power management cross reference carries it beside the resistance.
The gate threshold is printed as a typical minus 3 V without a window on this sheet, which is a gap a buyer should note. A part that turns on at minus 2 V and a part that turns on at minus 4 V behave differently in a divider driven gate, and the difference shows up as a slower turn on and more loss in the linear region. The how to verify a drop in replacement page treats a missing threshold window as a reason to measure rather than to assume.
Because the vendor base is narrow, the practical answer for a long life product is often to buy the last time buy quantity rather than to qualify a substitute. Our last time buy and LTB planning page describes how that quantity is calculated from the forecast and the storage life.
Questions we answer before a reel is booked
The first question is the gate drive. With a 200 V rail, the gate has to be held at least 10 V below the source, and a resistor from gate to ground with a 15 V zener does that. Without the zener the gate sees the full rail on a transient and the 30 V rating is gone. We ask for the clamp before quoting the part.
The second question is the current. At minus 2 A the loss is 7 W on a part that costs a heatsink, and at minus 1 A it is 1.8 W. If the load is above 2 A continuous, the honest answer is an N channel with a floating driver, and a buyer should be told that rather than sold a bigger P channel.
The third question is the diode. In a bridge the body diode conducts during dead time with a 5 V drop, which is 10 W at 2 A. That is not a number to discover on a thermal camera, and a circuit that relies on it should add a parallel schottky.