VBL16R07
Product Specifications
VBL16R07
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL16R07 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL16R07: a 600 V, 1.2 ohm N channel die for off line supplies
The VBL16R07 is an N channel MOSFET printed at 600 V from drain to source with a plus or minus 20 V gate, in the D2PAK outline with an isolated central mounting hole. The summary gives 1.2 ohm at a 10 V gate with 4 A flowing, a continuous drain current of 7 A with the case at 25 C and 5.2 A with the case at 100 C, a pulsed rating of 20 A, a single pulse avalanche energy of 880 mJ and a repetitive avalanche rating of 19 mJ at 8.7 A. The junction is rated to 150 C, and the sheet lists a dynamic dV/dt rating, ease of paralleling and simple drive requirements among the features.
This is a planar high voltage die rather than a super junction part, and the numbers show it. A 1.2 ohm channel at 600 V gives a specific resistance that is an order of magnitude above a super junction device, but the planar cell has a rugged avalanche behaviour and a capacitance that is easy to drive. The 190 W dissipation rating with the case at 25 C and the 0.65 C per watt junction to case describe a die that is meant for a heatsink, and the 40 C per watt board figure describes the same die on a bare plane.
The ratings a buyer checks first
| Drain to source voltage | 600 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 4 A | 1.2 ohm typical |
| Continuous drain current, case at 25 C and 100 C | 7.0 A and 5.2 A |
| Pulsed drain current | 20 A |
| Single pulse avalanche energy | 880 mJ from 37 mH at 6.7 A |
| Repetitive avalanche current and energy | 8.7 A and 19 mJ |
| Maximum power dissipation, case at 25 C | 190 W |
| Junction to case, junction to ambient | 0.65 and 40 C per watt |
| Case to sink, flat greased surface | 0.24 C per watt |
| Gate threshold at 250 microamp | 2.0 V minimum, 4.0 V maximum |
| Total gate charge at 360 V and 6.7 A | 200 nC maximum |
| Gate source and gate drain charge | 24 and 110 nC maximum |
| Input, output and reverse transfer capacitance | 2900, 270 and 92 pF |
| Turn on delay and rise time | 20 and 34 ns typical |
| Turn off delay and fall time | 130 and 37 ns typical |
| Body diode forward drop at 6.7 A | 1.8 V maximum |
| Body diode reverse recovery time and charge | 610 ns and 3.2 microcoulomb typical |
| Peak diode recovery dV/dt | 1.5 V per nanosecond |
| Operating junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The gate charge is the first number that decides the circuit. Two hundred nanocoulomb at a 10 V gate with 110 nC of it in the gate drain region means the driver has to move a large charge through the Miller plateau, and at 100 kHz that is 20 mA of average gate current plus the plateau current during the edge. A small controller pin will not do it, and a 1 A driver at 10 V gives an edge in the region of 200 ns, which is consistent with the 130 ns turn off delay the sheet prints.
The resistance is high, and the loss follows. At 4 A the channel dissipates 19 W, and at the 5.2 A the sheet allows with a 100 C case it dissipates 32 W. On a heatsink with a case held at 100 C, the 0.65 C per watt junction to case gives a 21 C rise, which is inside the 150 C limit. On a bare board at 40 C per watt the same 19 W is impossible, and the board level current is closer to 1.5 A for a 90 C rise. This is a part for a converter with a heatsink, not for a dense adapter on a bare board.
The avalanche numbers are the reason to choose a planar die. A single pulse of 880 mJ from 37 mH at 6.7 A is a large figure, and the repetitive rating of 19 mJ at 8.7 A describes a part that can absorb the energy of a leakage inductance every cycle. In a flyback converter the leakage spike is exactly that, and a 600 V planar part with this rating survives a clamp failure that a super junction device of the same resistance would not.
The body diode is slow: 610 ns of recovery and 3.2 microcoulomb recovered at 6.7 A. In a bridge or a half bridge that diode is the one that has to recover before the opposite switch turns on, so the dead time has to be long enough to cover 610 ns plus the current tail. In a flyback the diode never conducts in the reverse direction during normal operation, so the figure matters only during a fault.
Where a 600 V planar part earns its place
The first use is a flyback or a forward converter between 30 W and 80 W on a universal input, where the 600 V rating covers the reflected voltage plus the leakage spike and the 7 A current covers the peak primary current. The isolated mounting hole allows the tab to be screwed to a heatsink that is connected to the primary side or left floating, which is a real convenience in a metal chassis.
The second use is a power factor correction stage in a low power ballast or an LED driver, where the switching frequency is in the tens of kilohertz and the 200 nC gate charge is affordable. The avalanche rating covers the inductor current at the moment of a mains surge, and the planar cell is more tolerant of a hard commutation than a super junction die.
The third use is a high voltage load switch or a capacitive discharge path, where the part is on for a long interval and the resistance matters less than the avalanche and the dV/dt rating. The 1.5 V per nanosecond diode recovery limit is a constraint here, because a fast rising drain voltage on a conducting diode will exceed it.
Sourcing notes and the second source question
High voltage parts are where a second source is most likely to change the behaviour of the circuit, because the capacitance and the recovery charge set the clamp and the dead time. A 600 V part with 2900 pF of input capacitance and a 610 ns diode is not interchangeable with a super junction part of the same resistance, even if both are 600 V and both fit the same footprint. The power management cross reference keeps the capacitance and the recovery rows beside the resistance so that substitution is judged on the whole switch, not on one number.
The isolated mounting hole is a mechanical feature that a drop in replacement often lacks, and a buyer who has a chassis mounted heatsink cannot use a plain D2PAK without a new insulator and a new screw. The how to verify a drop in replacement page starts with the mechanical fit for exactly this reason.
Where the original vendor has stopped the line, the obsolete part replacement route looks at the circuit function first: a flyback clamp can often take a super junction part, a bridge leg usually cannot. Our supply side keeps both routes open rather than quoting whatever is on the shelf.
Questions we answer before a reel is booked
The first question is the driver. At 200 nC maximum the gate needs a driver that can deliver at least half an amp for the length of the edge, and a controller with a weak output will run the part in the linear region for microseconds on every turn on. This is the single most common cause of a 600 V switch failing in a bench build.
The second question is the clamp. The 880 mJ single pulse is large, but the repetitive figure of 19 mJ is the one that applies every cycle, and a clamp that is set too high will push the leakage energy into the die instead of the clamp. We ask for the leakage inductance and the clamp voltage before agreeing that the part is adequate.
The third question is the heatsink. A 190 W rating with the case at 25 C is a mounting statement, and the case to sink figure of 0.24 C per watt means the interface is counted separately from the junction to case figure. A buyer who adds only the two silicon figures will under estimate the total by the interface term, which on a 20 W loss is a 5 C error.