VBL15R22S
Product Specifications
VBL15R22S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL15R22S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL15R22S: a 500 V super junction part in TO-263
The VBL15R22S is an N channel super junction MOSFET in the TO-263 body, rated 500 V drain to source with plus or minus 30 V on the gate. On resistance is 127 milliohm at a 10 V gate, current is 22 A at a 25 C case and 17.6 A at 100 C, and the single pulse avalanche energy is 450 mJ. The vendor files it under server and telecom power supplies, switch mode supplies, power factor correction and lighting, including high intensity discharge and fluorescent ballast.
Super junction parts trade a more complex die for a much lower resistance at high voltage, and this one shows the trade clearly: 127 milliohm at 500 V is roughly a quarter of what a planar part of the same voltage and current would offer. The cost is a body diode with more recovered charge and a switching behaviour that is more sensitive to gate resistance and to the dv/dt at turn off. The sheet states a 50 V per nanosecond drain source dvdt limit and a 4.5 V per nanosecond reverse diode limit, both of which have to be respected by the gate network.
The ratings that matter at 500 V
| Drain to source voltage | 500 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate | 127 milliohm at 2.5 A |
| Continuous drain current | 22 A at 25 C case, 17.6 A at 100 C case |
| Pulsed drain current | 66 A |
| Single pulse avalanche energy | 450 mJ, 4 A into 30 mH |
| Power dissipation | 215 W |
| Linear derating factor | 1.65 W per C |
| Junction to case | 0.7 C per watt maximum |
| Junction to ambient | 62 C per watt maximum |
| Gate threshold voltage | 3 V minimum, 5 V maximum |
| Total gate charge | 65 nC typical, 70 nC maximum |
| Input capacitance | 2300 pF |
| Output capacitance, energy related | 63 pF, 0 to 520 V |
| Body diode recovery | 40 ns, 5.8 microcoulomb |
| Drain source dvdt limit | 50 V per nanosecond |
What the super junction rows tell a buyer
The threshold window is 3 V minimum and 5 V maximum at 250 microamp, which is high for a modern part and rules out a 5 V logic drive. A 10 V drive is assumed throughout the sheet, and the on resistance row is measured at 2.5 A, a light load for a 22 A device, which tells you the figure is a small signal resistance rather than a hot, full current one. At 20 A the resistance will be higher than 127 milliohm, and the junction temperature will decide how much higher.
The output capacitance is small, 63 pF energy related and 80 pF at 100 V, and the reverse transfer capacitance is 4 pF. That combination gives fast edges, which is good for efficiency and bad for emissions. The dvdt limit of 50 V per nanosecond is a hard number: with a 500 V rail, the whole edge has to take at least 10 ns, and the gate resistor is what sets it. A part switched faster than that limit can latch, and the failure looks like a random short after a few hundred hours rather than an immediate blow up.
Gate charge of 65 nC typical against 2300 pF of input capacitance is a moderate load for a driver, but the gate resistance is 0.8 ohm, so the peak current during the edge is set by the driver and the external resistor rather than by the die. The avalanche rating of 450 mJ into 30 mH with 4 A is unusual at this voltage and is a real benefit in a lighting ballast, where the strike transient is inductive and repetitive. The sheet is careful to call it a single pulse figure at 25 C, and the derating with temperature is steep.
The diode recovery of 40 ns and 5.8 microcoulomb is respectable for a super junction body, but in a hard switched bridge at 100 kHz the recovered charge is still a loss in the opposite device. A phase shifted or resonant topology places this die better than a hard switched one, and the vendor's own application list points that way.
Where 500 V at 127 milliohm is used
Power factor correction stages in a 400 V bus use this class as the boost switch, where the 500 V rating covers the 400 V output plus the overshoot and the low resistance keeps the conduction loss down at 5 A. Server and telecom rectifiers use it in the same position, and the 22 A rating is enough for a 2 kW stage at a reasonable duty. Lighting uses it in the ballast and in the high intensity discharge igniter, where the avalanche rating absorbs the strike pulse.
Solar micro inverters use a 500 V or 600 V device on the DC link, and this part fits a 350 V to 400 V link with margin. In every case the driver and the gate resistor are part of the part selection rather than an afterthought: a super junction die with a 50 V per nanosecond limit is only as good as the network that keeps it inside that limit.
Sourcing a high voltage super junction part
Second sourcing at 500 V is harder than at 40 V because the dvdt behaviour, the diode recovery and the threshold window all move between vendors, and a part that matches on resistance can fail on the edge rate. Our power management cross reference therefore starts from the voltage class and the dvdt limit, then compares gate charge and diode recovery, and only then looks at resistance. A customer who buys on resistance alone usually comes back with an emissions problem.
The practical test route for a replacement is in how to verify a drop in replacement, and for this family it adds two checks that the low voltage parts do not need: a double pulse test at the real bus voltage to measure the actual dvdt, and a thermal soak at the real switching frequency, because the switching loss at 500 V is a larger share of the total than at 40 V. We supply the part with the gate resistor value we recommend for the edge, and we sample the threshold and the resistance from each lot.
The TO-263 body also has a practical advantage in a lighting product: the tab can be screwed to an aluminium extrusion through an insulating pad, and the resulting thermal path is far better than any copper area on the board. That route is not available to a DFN part, which is why this body still sells into ballast and HID builds even where a smaller package would fit electrically. The 260 C soldering recommendation for 10 seconds at 1.6 mm from the case is the limit to respect on a wave or selective solder line.
Questions we get on this part
The first is whether 22 A is available at 100 C ambient. It is not: 22 A is at a 25 C case and 17.6 A at 100 C case, and the ambient figure is far lower because the junction to ambient path is 62 C per watt. The second is whether a 5 V gate drive works. It does not, because the threshold maximum is 5 V, so a 10 V drive is the assumption in every row of the sheet.
The third is about the avalanche rating in a repetitive application. The 450 mJ figure is a single pulse at 25 C, and a ballast that strikes several times a second accumulates stress; the derating curve and the repetition rate have to be checked, and a clamp is usually cheaper than the margin. The fourth is the diode: 5.8 microcoulomb of recovered charge at 400 V is a real loss in a hard switched bridge, and the topology should be chosen with that in mind.
On supply, we quote the reel with the date code and hold a per lot record that includes on resistance at 10 V and threshold. For a 500 V part the incoming record also notes the lot's avalanche sample where the vendor provides one, because that is the parameter most likely to vary between wafer lots at this voltage.