VBL1405
Product Specifications
VBL1405
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1405: a 40 V, 5 milliohm N channel switch in the TO-263 body
The VBL1405 is an N channel trench MOSFET in the TO-263 outline, printed at 40 V from drain to source with a plus or minus 20 V gate. The summary gives 5 milliohm at a 10 V gate with 30 A flowing and 6 milliohm at 4.5 V, a continuous drain current of 100 A with the case at 25 C and 60 A with the case at 125 C, and a pulsed rating of 220 A for 100 microseconds. The junction is rated to 175 C, and the vendor screens every part for gate resistance and for unclamped inductive switching, which is a stronger statement than the usual typical value table.
The thermal path is a known quantity in this body. The junction to case figure is 0.75 C per watt and the junction to ambient figure on a one inch board is 40 C per watt, so the same part is a 100 A device on a heatsink and a 20 A device on a bare plane. At 100 A the conduction loss is 50 W, which needs the tab held near 60 C; at 20 A it is 2 W, which a plane can carry.
The ratings a buyer checks first
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A | 5 milliohm typical |
| On resistance at 4.5 V gate, 30 A | 6 milliohm typical |
| Continuous drain current, case at 25 C and 125 C | 100 A and 60 A |
| Pulsed drain current for 100 microseconds | 220 A |
| Single avalanche energy and current | 125 mJ from 0.1 mH at 50 A |
| Power dissipation, case at 25 C and 125 C | 150 W and 98 W |
| Junction to case and junction to ambient | 0.75 and 40 C per watt |
| Gate threshold at 250 microamp | 1 V minimum, 3 V maximum |
| Total gate charge at 20 V drain and 30 A | 53.5 nC typical, 81 nC maximum |
| Gate source and gate drain charge | 14.5 and 13.2 nC typical |
| Total gate resistance at 1 MHz | 1.9 ohm typical, 3.8 ohm maximum |
| Input, output and reverse transfer capacitance | 3330, 1395 and 95 pF |
| Turn on delay and rise time at 10 V gate | 13 and 22 ns typical |
| Turn off delay and fall time at 10 V gate | 27 and 9 ns typical |
| Body diode forward drop at 30 A | 0.86 V typical, 1.4 V maximum |
| Reverse recovery time and charge at 30 A | 88 ns and 0.22 microcoulomb typical |
| Operating junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The pair of gate charge figures is where this part separates itself from the older 40 V dies. A 53.5 nC total with 13.2 nC of gate drain charge on a die that carries 100 A means the switching loss stays small at a switching frequency where a larger die would need a bigger driver. The 13 ns turn on delay and 9 ns fall are quick for a part in a TO-263, and the 22 ns rise against a 27 ns turn off delay suggests a cell that is not deliberately slowed.
The output capacitance row is unusual. At 1395 pF the output capacitance is high for a 40 V part with this resistance, and a high output capacitance is energy stored in the switch node that has to be dissipated every cycle. At 24 V and 200 kHz, 1395 pF stores about 0.4 microjoule per edge, which is 80 mW, small but not nothing. The benefit of the large cell area is the 5 milliohm resistance, so the trade is loss in the channel against loss in the capacitance, and at 30 A the channel wins clearly.
The 4.5 V row being only 20 per cent above the 10 V row is the practical advantage of a trench die at this voltage. A 5 V gate driver, which is what most point of load controllers provide, gets 6 milliohm, and a 3.3 V driver through a small resistor still turns the part on hard enough to stay under 10 milliohm. On a 40 V part with a threshold window reaching 3 V, that is a property worth confirming on the bench rather than assuming.
The avalanche figure is a single pulse at 50 A from 0.1 mH. The vendor also states UIS screening on every part, so the avalanche capability is measured rather than modelled, which is what a buyer wants when the load is inductive: a solenoid, a relay coil or a motor winding that is switched without a freewheel diode. The 100 microsecond pulsed current of 220 A is the other end of the same capability.
Where a 40 V TO-263 part earns its place
The first use is a 24 V motor drive or a 24 V solenoid driver, where a 40 V rating covers the flyback of the coil and the 5 milliohm channel keeps the conduction loss low at 20 A to 30 A. The high output capacitance costs a little at each edge, but on a 20 kHz drive the switching loss is a small part of the total.
The second use is the output stage of a 12 V to 5 V or 12 V to 3.3 V synchronous buck at 30 A to 50 A. The 40 V rating is generous for a 12 V rail and covers the ringing that a fast high side produces, while the low gate charge allows 300 kHz to 500 kHz without an expensive driver. The body diode recovery of 88 ns is fast enough that the dead time does not have to be padded.
The third use is a battery disconnect or a load switch on a 24 V pack, where the 175 C junction and the UIS screen cover the inductive kick of the harness. The 4.5 V row matters here because the switch is often driven from a supervisory pin at 5 V, and the part has to be fully on at that gate voltage in a warm enclosure.
Sourcing notes and the second source question
The 40 V class is crowded and the parts are not interchangeable on the parameters that matter. Two devices that both print 5 milliohm at 25 C can differ by 60 per cent at 125 C, and the gate charge can differ by a factor of two, which changes the driver and the switching loss. The power management cross reference keeps the hot resistance and the charge beside the cold resistance for that comparison.
The gate resistance screen is worth keeping in the approved list. A maximum of 3.8 ohm against a typical of 1.9 ohm tells a buyer that paralleling is supported and that the vendor measures the parameter; a part with only a typical value does not make that promise. Where two or three of these share a 100 A load, the pin to pin cross reference also confirms that the gate and source leads sit in the same place, because the loop inductance on the board depends on it.
A 40 V die in a TO-263 is a volume part and the reel is large, so a prototype order usually comes from a broken reel. Our date code management page describes how lots are kept separate when the goods inwards area receives a partial reel.
Questions we answer before a reel is booked
The first question is the gate drive. At 81 nC maximum, a 5 V driver with a 2 A peak output turns the part on in about 20 ns, which is inside the 22 ns rise the sheet prints. A weak pin without a driver will stretch the edge and put the part in the linear region for longer than the loss budget allows.
The second question is the mounting. A TO-263 soldered to a plane with a copper area of one square inch carries about 20 A at a 100 C rise, and the 100 A figure needs a heatsink or a cold plate. We ask for the tab temperature the enclosure can hold, then derate the current from the 125 C row.
The third question is the diode. In a motor drive the low side diode conducts during the freewheel interval, and 0.86 V at 30 A is 26 W for that interval. A buyer who has counted only the channel loss will find the heatsink too small, and the recovery time of 88 ns adds a spike that the 40 V rating has to absorb.