Contact Us

VBL1310

Brand: VBsemi
VBsemi VBL1310 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1310 — Discrete & Power Semiconductors | Superb Automation

VBL1310

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1310 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1310: a 30 V, 12 milliohm N channel switch for OR-ing and server rails

The VBL1310 is an N channel trench MOSFET in the D2PAK outline, printed at 30 V from drain to source with a plus or minus 20 V gate. The summary gives 12 milliohm at a 10 V gate with 28.8 A flowing and 18 milliohm at 4.5 V with 37 A, a continuous drain current of 50 A with the case at 25 C and 46 A with the case at 70 C, and a pulsed rating of 210 A. The junction is rated to 175 C, and the vendor lists OR-ing, server and DC to DC as the intended uses, which is exactly the family of applications where a 30 V part with a low resistance and a modest gate charge is the right tool.

The thermal picture is unusually complete for this class. The package dissipates 120 W with the case at 25 C and 85 W with the case at 70 C, and the drain current is also printed at a 25 C ambient, 27 A, which is the number a board level buyer should treat as the ceiling. That ambient row is rare on a data sheet and it saves a buyer from mistaking the case figure for a board figure.

The ratings a buyer checks first

Drain to source voltage30 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 28.8 A12 milliohm typical
On resistance at 4.5 V gate, 37 A18 milliohm typical
Continuous drain current, case at 25 C and 70 C50 A and 46 A
Continuous drain current, ambient at 25 C and 70 C27 A and 21 A
Pulsed drain current210 A
Single pulse avalanche energy and current94.8 mJ from 0.1 mH at 39 A
Power dissipation, case at 25 C and 70 C120 W and 85 W
Gate threshold at 250 microamp1.0 V minimum, 3.0 V maximum
Total gate charge at 10 V and 15 V drain35 nC typical
Total gate charge at 4.5 V gate25 nC typical
Gate source and gate drain charge15 and 20 nC typical
Total gate resistance at 1 MHz1.4 ohm typical, 2.1 ohm maximum
Input, output and reverse transfer capacitance1201, 255 and 170 pF
Turn on delay and rise time at 10 V gate18 and 11 ns typical
Turn off delay and fall time at 10 V gate70 and 10 ns typical
Body diode forward drop at 22 A0.8 V typical, 1.2 V maximum
Reverse recovery time and charge at 20 A52 ns and 70 nC typical
Operating junction and storage rangeminus 55 to plus 175 C

Reading the electrical table instead of the front page

The ambient current row does most of the work here. Twenty seven amps into a 12 milliohm channel is 8.7 W, and 21 A into an 18 milliohm channel, the 4.5 V case, is 7.9 W. Those are the losses a D2PAK on a server board can carry without a heatsink, because the tab is soldered to a copper plane and the plane is the heatsink. The 50 A case figure assumes a tab held at 25 C, which in a server means a cold plate, and the 46 A figure at a 70 C case is the number for a thermally managed board.

The two gate charge rows tell a buyer how to drive it. At 10 V the charge is 35 nC and at 4.5 V it is 25 nC, so a logic level driver charges less and switches slower; the 18/11 ns turn on and 70/10 ns turn off at 10 V are fast enough for a 300 kHz converter, and the turn off delay of 70 ns against a 10 ns fall is the signature of a cell with a low gate drain charge relative to its total. In an OR-ing path that switches only on a fault, none of this matters; in a synchronous buck it decides the dead time.

The resistance ratio between 4.5 V and 10 V is only 50 per cent, which is better than most 30 V parts, so a 5 V gate drive is a reasonable choice for a 20 A rail. The threshold window from 1 V to 3 V is wide, and a part at the top of the window driven from a 3.3 V pin has almost no overdrive, so the 4.5 V row is the honest one to use with a 5 V driver and the board should not be signed off on the 12 milliohm row unless the gate really reaches 10 V.

The diode is worth a line. A 0.8 V drop at 22 A and a 70 nC recovered charge is a fast body diode for a 30 V part, which matters in an OR-ing path where two channels conduct in parallel during a supply changeover. A slow diode would produce a larger reverse recovery spike into the rail, and on a 30 V bus there is very little headroom above the 30 V rating for that spike.

Where a 30 V D2PAK part earns its place

The first use is OR-ing two 12 V supplies into a server or a telecom line card. The channel sits in series with each supply and conducts continuously, so the on resistance is the whole loss; 12 milliohm at 20 A is 4.8 W, which a D2PAK on a plane can hold. The fast body diode keeps the changeover clean when one supply drops, and the 175 C junction gives margin for the interval when both diodes conduct.

The second use is the synchronous buck output stage on a 12 V input rail, where the 30 V rating covers the switch node ringing and the low resistance keeps the efficiency above 90 per cent at 20 A. The gate charge of 35 nC at 10 V allows a 500 kHz switching frequency without the driver dominating the loss, and the 4.5 V row makes a 5 V gate drive workable for a lower cost driver.

The third use is battery protection or a load switch on a 24 V nominal battery, where a 30 V part is at the edge. A fully charged 24 V pack sits near 29 V and a charger can push it higher, so the 30 V rating leaves nothing for transients. In that position the next voltage class up is the correct part, and a buyer should not be persuaded by the low resistance of a 30 V die on a 24 V pack.

Sourcing notes and the second source question

OR-ing parts are usually qualified on one parameter, the on resistance at the gate voltage the board actually provides, and two 30 V parts that both print 12 milliohm at 10 V can print very different numbers at 4.5 V. The power management cross reference puts the 4.5 V row next to the 10 V row so a candidate is compared on the drive the board can supply.

Paralleling is common in OR-ing and in high current buck stages, and the gate resistance window of 1.4 to 2.1 ohm is narrow enough that two parts share the switching interval well. A second source with a wider gate resistance window will not share as evenly, which shows up as one device running hotter than its neighbour. The pin to pin cross reference keeps the gate and source leads in the same table as the resistance and charge, because a different lead arrangement changes the loop on the board as much as a different die does.

Where the original part is on a long lead time, the answer is often a part in the same family with a different voltage class rather than a competitor part with the same footprint. Our component lead time solutions page describes how we hold a qualified alternative beside the primary part before the shortage rather than during it.

Questions we answer before a reel is booked

The first question is the gate drive voltage, because the whole loss calculation hangs on it. A 12 V rail through a 10 ohm resistor gives 10 V at the gate and the 12 milliohm row applies; a 5 V rail gives about 4.7 V and the 18 milliohm row applies, which is 50 per cent more loss for the same current. We ask for the driver before quoting a current.

The second question is whether the part is in a socket or soldered. A D2PAK in a socket has a contact resistance and a much worse thermal path than one soldered to a plane, and the ambient current row assumes the soldered case. A socketed prototype that runs cool can still fail in production if the production board has less copper under the tab.

The third question is the current sharing. Two of these in parallel share well on resistance but not perfectly on threshold, and a 1 V threshold spread means one part takes more current during the switching interval. In a 40 A OR-ing path the static sharing is set by resistance and is fine; in a fast switching stage the dynamic sharing sets the hot spot, and the gate resistance window is the parameter to check.