VBK362KS
Product Specifications
VBK362KS
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBK362KS from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBK362KS: two 60 V N channel switches in one SOT-363 body
The VBK362KS is a dual N channel trench MOSFET in the six lead SOT-363 outline, which is the same body the industry also calls SC-70. Each channel is printed at 60 V from drain to source with a plus or minus 20 V gate, an on resistance of 1.8 ohm at a 10 V gate with 500 mA flowing and 3 ohm at 4.5 V with 200 mA, and a continuous drain current of 350 mA with the ambient at 25 C. The pulsed rating is 900 mA, the junction is rated to 150 C, and the pair is isolated from each other inside the package, which is what makes it useful as two independent level shifters or two drivers in one place.
This is a small signal part, and the numbers should be read at that scale. The package dissipates 0.35 W at 25 C ambient and the junction to ambient figure is 350 C per watt, so the thermal budget is the limit long before the current rating is. At 350 mA the conduction loss is 0.22 W, which is already two thirds of the package rating, and the die would sit 77 C above ambient. The useful continuous current on a real board is closer to 150 mA, where the loss is 40 mW and the rise is 14 C.
The ratings a buyer checks first
| Drain to source voltage per channel | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 500 mA | 1.8 ohm typical |
| On resistance at 4.5 V gate, 200 mA | 3 ohm typical |
| Continuous drain current, ambient 25 C and 100 C | 350 mA and 230 mA |
| Pulsed drain current | 900 mA |
| Power dissipation, ambient 25 C and 100 C | 0.35 W and 0.14 W |
| Junction to ambient on an FR4 board | 350 C per watt |
| Gate threshold at 250 microamp | 1 V minimum, 2 V typical, 2.5 V maximum |
| Gate body leakage at plus or minus 10 V | plus or minus 150 nA maximum |
| Zero gate drain current at 60 V and 125 C | 500 microamp maximum |
| Total gate charge at 10 V and 250 mA | 0.6 nC typical, 0.8 nC maximum |
| Input, output and reverse transfer capacitance | 30, 6 and 2.5 pF |
| Turn on and turn off time | 25 and 35 ns typical |
| Body diode forward drop at 200 mA | 1.3 V maximum |
| Operating and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The gate charge is the number that decides how this part is used. At 0.6 nC typical and 0.8 nC maximum, a logic pin can drive a channel without a buffer, a gate resistor network or a driver chip, and the 30 pF input capacitance means the pin sees almost nothing. That is the whole point of the part: it replaces a bipolar transistor and two resistors in a level shifter or a small relay driver, and it does it with a defined threshold and no base current.
The resistance rows tell a different story. At 4.5 V the channel is 3 ohm, which is 67 per cent above the 10 V figure, and the threshold window tops out at 2.5 V. A gate held at 3.3 V therefore has only 0.8 V of overdrive on a worst case part, which is enough for a 200 mA load and not enough to claim the 1.8 ohm number. A product that drives the gate from a 3.3 V microcontroller should budget the 3 ohm row, and a product that drives it from 5 V gets most of the way to the lower figure.
The two channels share one package and one thermal path. The 0.35 W dissipation rating is for the whole body, not per channel, so two channels each carrying 250 mA at 1.8 ohm dissipate 0.23 W together and the junction sits 80 C above ambient. Turning both channels on at the same time is fine electrically and expensive thermally, and a symmetric load on both halves is the case that reaches the limit first.
The leakage rows matter more than they look. At 125 C the drain leakage is 500 microamp and the gate leakage at plus or minus 10 V is plus or minus 150 nA, so a channel that is meant to hold a node off in a warm enclosure will leak a measurable current. In a sample and hold path or a battery isolation switch, that leakage is the parameter that decides whether the part is acceptable, not the on resistance.
Where a dual 60 V SOT-363 part earns its place
The classic use is a low side driver for a relay, a solenoid, a lamp or a small display, where the coil or the filament is switched on the ground side and the gate is driven from a logic pin. Two channels in one body then fit two loads in the space of one SOT-23, and the 60 V rating covers the inductive kick of a 24 V coil with a diode across it. The 150 C junction and the 900 mA pulse allow a short inrush without a separate limiter.
The second use is a solid state relay or an analogue switch in a signal path, where the low gate charge and the 2.5 pF reverse transfer capacitance matter more than the current. A pair of these in series with opposite gates makes a bidirectional switch that blocks in both directions and leaks about 1 microamp at 60 V. That is a workable replacement for a small electromechanical relay in a product that cannot tolerate contact wear.
The third use is level shifting between a 3.3 V logic domain and a 12 V or 24 V load, where the gate is driven from the low side and the drain pulls up to the high rail. The threshold window of 1 V to 2.5 V is wide enough that a 3.3 V pin turns the channel on hard, and the 20 V gate rating leaves room for a pull up to 12 V without a clamp. A 24 V pull up does need a clamp, because the gate would otherwise sit above its rating when the channel is off.
Sourcing notes and the second source question
Dual MOSFETs in a six lead body are the worst case for a drop in replacement, because the pin order is not fixed between vendors. Some parts put the two drains on pins 1 and 6 and the two sources on 3 and 4, others cross them, and a part that matches on voltage, resistance and package can still be wired the other way round. The pin to pin cross reference lists the lead assignment next to the electrical data for that reason.
The other trap is the current rating basis. Some dual parts print 350 mA from a case temperature, others from an ambient, and the two are not comparable on a 350 C per watt package. A buyer comparing two data sheets by the headline current can easily pick the part that will run hotter. The how to verify a drop in replacement page sets out the sequence we use: footprint, pin order, threshold window, then thermal, and only then a sample.
Supply for a small signal dual is usually easy, and the risk is the opposite one: a vendor change in the die can move the threshold without moving the part number. Our date code management page describes how we keep lots separated on a part where the threshold is the parameter that matters.
Questions we answer before a reel is booked
The first question is whether the gate can be driven directly. At 0.8 nC maximum and 30 pF, yes, from any pin that can source a milliamp, and the 25 ns turn on means there is no need for a gate resistor unless the rise is too fast for the load. A 100 ohm resistor in series with the gate costs nothing and removes the ringing that a long trace produces.
The second question is the threshold spread. The window runs from 1 V to 2.5 V, which is a factor of two and a half, so a batch can contain parts that turn on at a lower gate voltage than the previous batch. In a circuit that relies on the channel being off with 1 V on the gate, that spread is a real risk, and a pull down resistor is the answer rather than a tighter part number.
The third question is the load. A relay coil of 200 mA at 24 V is 0.1 W in the channel at 2.4 ohm, which is comfortable; a lamp with a 2 A cold filament is not, even for the 900 mA pulse. We size these parts against the steady state current and the ambient, and we ask for the coil resistance rather than the coil voltage, because the voltage says nothing about the current.