HXN40009
Product Specifications
HXN40009
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40009 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40009: 51 dBm at 32 V, the 126 W member of the L band family
The HXN40009 sits one step above the 48 dBm part in the same 1.2 to 1.4 GHz band and on the same 32 V rail. The published rows are at least 51 dBm of saturation power, at least 13 dB of gain, at least 50 per cent efficiency, 50 ohm ports, plus or minus 0.8 dB of flatness and continuous wave operation. Fifty one dBm is 125.9 W, which doubles the output of the 48 dBm member for the same 13 dB of gain and the same rail.
Doubling the output at the same rail doubles the current. At 50 per cent efficiency the DC input is 251.8 W, the drain current is 7.87 A at 32 V, and the heat to remove is 125.9 W. Nine and a half amperes of drain current through a bond wire and a flange is a packaging question as much as a silicon one, and the vendor page publishes neither the flange nor the bond wire arrangement, which is the first thing a buyer of this part has to resolve.
The drive is 38 dBm, or 6.3 W. That is above the saturation output of the 40 dBm member and below the 48 dBm member, so a chain built from this family for 126 W runs a 48 dBm stage backed off by 10 dB as its driver, which is a comfortable place for a 63 W part and keeps the drive chain at two power stages plus a small signal front end.
The combination of a 50 ohm internal match and a 200 MHz band is what makes this part usable in a system with no external matching. At 7.87 A of drain current the internal match also carries the full output current, and its loss is part of the 50 per cent efficiency budget rather than something a buyer adds on top. That is worth remembering when the measured efficiency comes in below the printed floor: the match, not the die, is often where the last two points went.
The parameter rows the vendor publishes
| Part class | Gallium nitride power transistor with internal matching |
| Frequency range | 1.2 to 1.4 GHz |
| Saturation power as published | at least 51 dBm |
| Saturation power in watts, calculated | 125.9 W |
| Gain as published | at least 13 dB |
| Efficiency as published | at least 50 per cent |
| Output at 1 dB compression | not published |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Drain voltage | 32 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| DC input at saturation, calculated | 251.8 W |
| Dissipation at saturation, calculated | 125.9 W |
| Drain current at saturation, calculated | 7.87 A |
| Drive power for rated output, calculated | 38 dBm, 6.3 W |
| Matching technology | in-plane matching synthesis on a film hybrid carrier |
| Stated application | RF and microwave systems |
| Package and flange | not published on the parameter page |
| Thermal resistance | not published |
| Scattering parameters | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum | not published |
| Member below, same band and rail | HXN40008 at 48 dBm and 13 dB gain |
| Member above, same band, lower rail | HXN40010 at 53 dBm from 28 V in pulsed operation |
| Member above, same band, higher rail | HXN40011 at 56 dBm from 50 V in pulsed operation |
| Same output, lower band | HXN43001 at 50 dBm over 1 to 4 GHz from 30 V |
| Same output, higher band | HXN43002 at 50 dBm over 2 to 4 GHz from 28 V |
126 W of heat and the flange nobody publishes
The thermal case for this part is not an arithmetic exercise, it is a mechanical one. At 50 per cent efficiency the device sheds 125.9 W in continuous wave, and the vendor publishes no junction to case figure, no flange material and no mounting specification. A copper tungsten flange with a sintered die attach and a 0.5 C per watt path is what this power level normally needs; at 0.5 C per watt, 126 W is 63 C of rise and a 60 C cabinet gives 123 C at the junction, which is inside a GaN channel limit and outside a comfortable one.
At 1 C per watt the same 126 W is 126 C of rise and there is no cabinet temperature at which that works. This is the reason a 126 W continuous wave stage is normally either liquid cooled or pulsed. The family offers both routes, and the choice between them costs a build cycle if it is made late.
The current adds a second constraint. At 7.87 A the DC feed, the choke and the drain decoupling have to carry a steady current that is several times what a 10 W stage draws, and the parasitic inductance of that feed is what turns a switch off transient into a drain voltage excursion. A 32 V rail with a 30 nH feed and a 8 A step is a 240 V spike before any clamp, so the decoupling and the clamp are part of the same thermal and electrical budget.
Where the datasheet stops and the bench starts
The published list has no compression point, so 51 dBm again describes a saturated condition only. For a communication system this is the wrong figure to buy on: a 51 dBm saturated device may deliver 45 dBm at the compression point a modulated signal needs, and the sheet does not say where that point is.
There is no small signal gain against frequency, only a plus or minus 0.8 dB flatness row taken in saturation. A cascade with a filter in front of this stage needs the input return loss at the band edges, and that number is missing along with the scattering parameters.
There is also no bias information at all, no quiescent current, no gate voltage window and no recommended sequence. For a device that draws 7.87 A at 32 V, a gate bias that is applied in the wrong order destroys the part on the first power up, so the bias method has to be part of the purchase conversation rather than a detail left to the assembly house.
Finally, the mechanical data is missing. At this power level the flange flatness, the mounting torque and the interface material determine the junction temperature as much as the silicon does, and a buyer who cannot quote the flange cannot quote a heatsink.
Where a 126 W continuous wave L band part still fits
It fits a fixed installation with a real cooling path: a ground station transmitter, a laboratory driver amplifier, a high power test source, or the driver stage for a 56 dBm pulsed device where the duty cycle lowers the average dissipation to a sixth. In the last case the 126 W peak becomes roughly 13 W average at 10 per cent duty, which turns an impossible thermal problem into a heatsink the size of a paperback.
It does not fit a compact enclosure with forced air only, and it does not fit a linear multicarrier system. It also does not fit a 28 V system, because the rail is 32 V and the family's pulsed members include parts built for 28 V for exactly that reason, so a system already committed to 28 V should read the 53 dBm member instead of this one.
Our RF power transistor cross reference work holds the rail, the duty cycle, the drive level and the gain per approved alternate, and the rail is the row that decides the whole bias supply. The defense grade components page covers the documentation and traceability that L band power devices normally carry into a programme.
Questions we answer before an order is placed
The first is whether the system is continuous wave or pulsed, because that single answer changes the required carrier by an order of magnitude. The second is the drive chain, since 38 dBm has to come from somewhere and a 48 dBm member backed off by 10 dB is the natural source. The third is the flange and the interface, because at 126 W the mechanical stack is the electrical performance.
The fourth is the measurement route. Power sweeps at 1.3 GHz come from the customer bench or a partner RF laboratory, and our own test covers DC parameters, functionality and customer fixtures. That is the honest division for a part of this class, and it belongs in the quotation rather than in the first article report.
The fifth is the documentation set. Ask for the outline drawing, the flange material, the pinch off window, the measured efficiency at the customer frequency and the moisture classification, since none of them is on the vendor page. Our incoming inspection plan records the delivered lot against that list, and the passive parts around a stage this size are kept together with the device as one kit on the quotation.