Contact Us

HXN42002

Brand: Hisiwell
Hisiwell HXN42002 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN42002 — Discrete & Power Semiconductors | Superb Automation

HXN42002

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN42002 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN42002: half a kilowatt over 400 MHz of S band from a 48 V rail

The HXN42002 is the widest band member of the S band group in this family. It covers 2.7 to 3.1 GHz, prints an output power of 57 dBm as a P3dB typical figure, a power gain of 13 dB as G3dB typical, a power added efficiency of 55 per cent typical, and a 48 V rail, in 100 microsecond pulses at 10 per cent duty, in a metal package. The index table lists it at 57.5 dBm, and the difference between the two rows is discussed below.

Four hundred megahertz at this power is a wideband saturated stage, and the 48 V rail is 2 V below the 50 V parts either side of it in the catalogue. That 2 V matters at 19 A: the same 501 W output at 55 per cent efficiency draws 911 W of DC, which is 19.0 A at 48 V against 18.2 A at 50 V, so a supply built for a 50 V part will run this one at a higher current for the same power and needs its current limit set accordingly.

The page describes the part as a gallium nitride internally matched power transistor for standard communication bands, providing optimal power and gain performance in 50 ohm systems, with no external matching required. The words standard communication bands are doing real work here: 2.7 to 3.1 GHz spans the S band radar allocation, the lower part of the 3 GHz point to point and satellite bands, and instrumentation uses, so the part is a general purpose saturated amplifier rather than a channelised device.

The 100 microsecond pulse at 10 per cent duty gives an average dissipation of 41.0 W against 410.1 W during the pulse, and an average drain current of 1.90 A against 19.0 A. As with the rest of this family, the average tells the heatsink what it will see and the peak tells the supply and the feed what they must survive.

The parameter rows Hisiwell publishes for HXN42002

Part classGallium nitride power transistor, internally matched, metal package
Frequency range2.7 to 3.1 GHz
Output power, product page row57 dBm at 3 dB compression, typical
Output power, index table row57.5 dBm saturated
Output power in watts from the page row, calculated501.2 W
Output power in watts from the index row, calculated562.3 W
Gain13 dB at 3 dB compression, typical
Power added efficiency55 per cent typical
Drain voltage48 V
Flatness across the bandnot published, the index prints a slash
Operating modepulsed, 100 microsecond pulse width at 10 per cent duty
Input and output impedance50 ohm
DC input at 57 dBm and 55 per cent, calculated911.2 W
Drain current at saturation, calculated18.98 A at 48 V
Dissipation during the pulse, calculated410.1 W
Average dissipation at 10 per cent duty, calculated41.0 W
Average drain current at 10 per cent duty, calculated1.90 A
Drive power for the rated output, calculated44 dBm, 25.1 W
Output per 100 MHz of the band, calculated125.3 W
Thermal resistance, junction to casenot published
Transient thermal impedancenot published
Package outline and dimensionsmetal package, no dimensions in text
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published on this page
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Same band family, 50 V rail, 54 dBmHXN40037 over 2.7 to 2.9 GHz at 55 per cent
Same band family, 48 V rail, 57.5 dBmHXN42012 over 2.7 to 3.5 GHz at 13.5 dB gain

P3dB on the page against saturation in the index

The product page prints 57 dBm at 3 dB compression and 13 dB of gain at the same condition, while the index table prints 57.5 dBm and no compression column. Those two rows describe different quantities: a compression point is a linearity figure measured where the gain has fallen by 3 dB, and a saturation figure is the ceiling of the output against input curve. For a gallium nitride stage the two usually sit within a decibel of each other, so the 0.5 dB gap between the rows is small in engineering terms and large in procurement terms, because a system budget written on 57.5 dBm of guaranteed output is half a decibel above what the product page promises.

The useful reading is to take 57 dBm as the figure with a published measurement condition attached and to treat 57.5 dBm as the catalogue headline. If a system needs 57.5 dBm, the margin has to be found in the chain, not in the part.

The flatness row is the second gap. Every other member of this family publishes plus or minus 0.8 dB across its band; this part prints a slash, and its band is twice as wide as the 2.7 to 2.9 GHz parts. On a 400 MHz internally matched stage, a flatness figure would be the most useful row on the page, and its absence is worth raising with the vendor before a build is frozen around a level output assumption.

Four hundred megahertz and what it does to the arithmetic

A 400 MHz window at 501 W means the matching network is carrying 125 W per 100 MHz of bandwidth, and the efficiency figure of 55 per cent is an average across that window rather than a point value. On a wideband internally matched part the efficiency normally peaks near the centre and falls at the edges, so 55 per cent typical at the centre can be 50 per cent at 2.75 GHz and at 3.05 GHz, which moves the dissipation from 410 W to 501 W at the edges for the same output.

That spread, not the headline, is what the cooling has to survive. A build that works at the centre frequency and is then tested at the band edge is the classic failure mode for a wideband stage, and the counter is to specify the case temperature at both edges rather than at the centre.

The 48 V rail also has a consequence for the driver: 25.1 W of drive is needed for the rated output, and the gain of 13 dB is a G3dB figure, so the small signal gain will be higher and the gain under drive will fall. A chain that produces 25.1 W at 2.9 GHz with 2 dB of margin is the right target, and the margin covers the isolator, the cable and the connector between the driver and this device.

Where a 400 MHz, 501 W stage at 48 V fits

The fit is a transmitter that has to cover the whole S band radar allocation with one device, or a test amplifier that sweeps 2.7 to 3.1 GHz for antenna and receiver work. The 48 V rail is convenient because it comes from a standard telecom or vehicle supply, and the metal package is what a high power assembly expects.

It is a poor fit for a system that needs a levelled output across the band, because the flatness is not published, and a poor fit for continuous wave at this power. It is also a poor fit where the supply is fixed at 50 V and cannot be trimmed, because the current at 48 V is 4 per cent higher for the same output and the current limit has to be set for the higher value.

Our RF power transistor cross reference work records the rail, the mode and the compression condition of each part in this group, because a 48 V part and a 50 V part with the same dBm headline are not interchangeable in a built assembly: the bias network, the current limit and the cooling all change with the rail.

Questions we answer about HXN42002 before a lot is booked

The first is which power row the vendor will guarantee. Ask whether the order is against 57 dBm at 3 dB compression or 57.5 dBm saturated, and ask for the measurement condition, because the two lead to different system margins.

The second is the flatness across 2.7 to 3.1 GHz. With a slash in that column, the only way to know is a sweep on the first article at three frequencies, and that sweep belongs on the customer bench or at a partner RF laboratory.

The third is the lot and the bias. No pinch off voltage is published for this part, so the gate supply has to be set from a measured first article, established before the drain every time. The purchase order names the band, the rail and the pulse condition, and the incoming inspection plan records the marking, the flange and the DC behaviour. Where the 48 V rail is a system constraint rather than a preference, our one stop RF supply view lists the parts in this family that share that rail.