Contact Us

VBGQA1802

Brand: VBsemi
VBsemi VBGQA1802 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQA1802 — Discrete & Power Semiconductors | Superb Automation

VBGQA1802

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQA1802 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQA1802: an 80 V 180 A switch in the DFN 5 by 6 body

The VBGQA1802 is an N channel trench MOSFET in the DFN 5 by 6 outline, printed at 80 V with plus or minus 20 V on the gate and a 175 C junction. On resistance is 1.9 milliohm at a 10 V gate with 20 A flowing and 2.3 milliohm at 4.5 V with 46 A, rising to 2.8 milliohm at 125 C and 3.8 milliohm at 175 C. Continuous drain current is 180 A with the case at 25 C and 108 A with the case at 100 C, the pulsed rating is 324 A, and single pulse avalanche energy is 133 mJ at 90 A peak from 0.1 mH. Input capacitance is 8600 pF and gate charge 92 nC typical.

The threshold window on this part is 1 V to 3 V with 2 V typical, which is a full volt below the 100 V devices in the same catalogue. That single row changes what the part can be driven by: a 4.5 V logic rail reaches a published 2.3 milliohm, where the 100 V parts only publish a 5 milliohm at the same gate. For a 48 V system run from a 5 V housekeeping rail, that is the difference between needing a gate driver and not.

The ratings a buyer checks first

Drain to source voltage80 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 20 A, 25 C1.9 milliohm
On resistance at 4.5 V gate, 46 A, 25 C2.3 milliohm
On resistance at 125 C and 175 C2.8 and 3.8 milliohm
Continuous drain current, case at 25 C180 A, package limited
Continuous drain current, case at 100 C108 A, package limited
Pulsed drain current and diode pulsed current324 and 420 A
Single pulse avalanche energy and current133 mJ from 0.1 mH, 90 A peak
Power dissipation with the case at 25 C136 W
Junction to ambient, ten second and steady state15 to 18 and 40 to 50 C per watt
Junction to case0.85 C per watt typical, 1.1 maximum
Gate threshold voltage at 250 microamp1 V minimum, 2 V typical, 3 V maximum
Drain leakage at 30 V, 25 C, 125 C and 175 C1 microamp, 50 microamp and 250 microamp maximum
Input, output and reverse transfer capacitance8600, 470 and 225 pF at 85 V
Total gate charge, gate source and gate drain92, 16 and 19 nC typical
Turn on delay and rise time20 and 15 ns typical
Turn off delay and fall time35 and 20 ns typical
Diode forward drop at 20 A, reverse recovery1 V typical, 1.5 V maximum, 4 ns typical

Reading the electrical table instead of the front page

At 180 A the loss is 62 W, which against 0.85 C per watt puts the die 52 C above a case held at 25 C. On the steady state ambient row the honest figure is about 55 A, where 2.9 W of loss lifts the junction 115 C over a 60 C ambient. At 175 C the resistance is 3.8 milliohm, so the same 55 A dissipates 11.5 W and the pad would have to be twice the size to hold that, which is why a product that must run hot should be sized on the 175 C column and land somewhere near 30 A to 35 A continuous.

The 80 V rating against a 48 V rail is the interesting margin question. A 48 V rail with a 20 per cent transient is 58 V, and a switching node spike of 15 V on top reaches 73 V, which leaves 7 V of headroom. That is enough for a well clamped node and not enough for a long cable into a hot plug event, so a buyer with either should clamp the drain rather than rely on the avalanche rating, which at 133 mJ is a single pulse number.

The leakage rows are specified at 30 V on an 80 V part, which is unusual and worth noting: the vendor has tested the blocking behavior at less than half the rating. It does not invalidate the 80 V rating, but a buyer who needs to know the leakage near the full blocking voltage will not find it in this table and should ask for it.

The gate charge of 92 nC with a 19 nC gate drain charge and a 15 ns rise time describes a die that wants a real driver even though the threshold allows a logic level drive. A 4.5 V rail reaches 2.3 milliohm but a 4.5 V driver still has to deliver 92 nC in 15 ns, which is over 6 A of peak current. The low threshold reduces the drive voltage, not the drive current, and that distinction is where a product using a microcontroller pin for the gate usually fails.

Where an 80 V logic level device earns its place

The first use is a synchronous rectifier in a 48 V to 12 V converter, where the gate can be driven from a 5 V rail and the 1.9 milliohm keeps the conduction loss down at 40 A to 60 A. The second is a battery disconnect on a 48 V to 60 V pack, where the 80 V rating gives room for the charger transient and the 324 A pulse covers the inrush into a capacitive load.

The third is a motor drive for a 48 V e bike or a light industrial actuator, where the 175 C junction and the 133 mJ avalanche cover the inductive kick of a commutating winding. The fourth is a load switch on a 48 V telecom rail, where the low threshold lets the part be driven by a supervisor on a 5 V rail without a level shifter.

What the part is not is a 60 V system switch with a 60 V transient. With 80 V of blocking and a spike that can reach 73 V on a 48 V rail, a 60 V rail leaves no headroom at all, and a buyer on a 60 V nominal system should be looking at a 100 V part at 3 milliohm and accepting the higher conduction loss.

Sourcing notes and the second source question

Second sourcing this part means matching the threshold window before anything else, because a candidate with a 2.5 V to 4.5 V window will not work on the 4.5 V drive the board was built around, even if the resistance at 10 V is identical. The power management cross reference puts the threshold and the resistance at both gate voltages in one row, which is the comparison that decides the case.

The footprint check comes second: a DFN 5 by 6 with a different tab area needs a different stencil aperture, and a candidate that is electrically perfect can still fail on voiding after reflow. The pin to pin cross reference records the land pattern beside the electrical rows for that reason.

Where a buyer is moving off a part that has gone long lead, the component lead time solutions page describes how a candidate is qualified on an existing board without a new thermal cycle.

Questions we answer before a reel is booked

The first is whether the 4.5 V resistance row is usable. It is, with the caveat that a worst case part at a 3 V threshold has 1.5 V of overdrive at 4.5 V, and the 2.3 milliohm row was measured at 46 A where self heating is already present. Ten volts remains the condition for the headline 1.9 milliohm.

The second is the hot current. The 180 A figure needs a soldered tab on heavy copper, and a bolted or clipped connection does not reach 0.85 C per watt. On a one inch pad the number is 55 A cold and 30 A at a 175 C junction.

The third is the diode. A 4 ns typical recovery against a 135 ns maximum is the same spread as its 40 V sibling, and the dead time in a synchronous stage has to be set from the maximum. The diode forward drop of 1 V at 20 A is also higher than a discrete Schottky would give, which matters in a converter that spends a long time in freewheel.