VBGQA1152N
Product Specifications
VBGQA1152N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQA1152N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQA1152N: 150 V in a 5 by 6 DFN
The VBGQA1152N is a single N channel MOSFET in a DFN8 body measuring 5 mm by 6 mm, rated at 150 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 50 A of drain current and 21 milliohm at a 10 V gate. The silicon is a shielded gate trench.
150 V in a 5 by 6 DFN is the interesting part of this page. The voltage class is normally found in a TO252 or a TO220, where the creepage from the drain tab to the source lead is a few millimetres of moulding. In a 5 by 6 body the exposed pad is large and the gap to the gate and source pins is under a millimetre, so the package is working near the limit of what a surface mount body can hold at this voltage.
The part is aimed at converters that run from a 48 V to 96 V rail and need a compact switch: a 48 V to 12 V buck, a 96 V to 24 V converter, a 60 V PoE injector, and the primary of a small flyback on a 96 V bus. In each case the 150 V rating gives margin over a 96 V rail and the body keeps the board small.
Key data for the VBGQA1152N
| Configuration | Single N channel |
| Package | DFN8, 5 mm by 6 mm, exposed pad |
| VDS | 150 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 50 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 21 milliohm |
| Technology | Shielded gate trench |
| Body diode | Intrinsic, cathode at the drain |
| Loss at 10 A | 2.1 W through the channel |
| Thermal path | Exposed pad to copper, vias carry the heat |
| Creepage | 150 V on a 5 by 6 pad needs a slot or a coating at pollution degree 2 |
What changes when a 150 V die goes into a small body
The first change is thermal. A 5 by 6 DFN has an exposed pad about 4.5 mm by 5 mm, and the heat leaves through the solder, the copper and the vias. At 2 W that is easy. At 8 W the via count and the copper area decide the junction temperature, and the datasheet thermal resistance is measured on a board that is larger than most products.
The second change is the voltage standing on the pad. The drain is the pad, and at 150 V the gap from the pad edge to the source and gate pins is under a millimetre of moulding. In a dry environment that is fine. In a humid or dusty one, a conformal coat or a slot in the copper is worth adding, and the pad should not be placed where contamination can bridge to a neighbouring trace.
The third change is the current density at the pad. At 50 A the current has to spread across 4.5 mm of pad, and the vias under it are in parallel with the copper. A pad with eight vias and a plane underneath behaves very differently from a pad with two vias and a long trace.
Gate drive and the 3 V threshold
A 3 V threshold means the die starts to conduct at a gate voltage well inside a 5 V logic window, so a microcontroller pin can turn it partly on. That is useful for a low current switch and unhelpful for a fast one: the same low threshold makes the die sensitive to the Miller coupled charge from the drain, and a fast drain edge can pull the gate up and turn the part back on.
With a 10 V driver the resistance is the 21 milliohm in the table. With a 4.5 V driver the resistance is higher and the page does not print the figure, so a 4.5 V rail has to be validated on the bench before the loss budget is fixed.
For a hard switched converter at 100 kHz the gate resistor is the usual tool: a few ohms in series slows the drain edge enough to keep the ringing inside 150 V and still fast enough that the crossover loss stays small. The value comes from the loop inductance, not from the driver datasheet.
Where the part fits and where it does not
It fits a 48 V to 12 V buck, a 96 V to 24 V converter, a 60 V PoE injector, the primary switch of a small flyback on a 96 V bus, and a battery disconnect on a 72 V pack. It does not fit a 110 V bus without derating, a converter at 15 A continuous without a good thermal pad, or a board where the pad cannot be coated and the environment is damp.
For a small body at this voltage, the two things worth checking before a substitute is accepted are the pad geometry and the thermal vias. Our power management cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour in a small package.
The sourcing side of this part is covered on the date code management. For a part that sits on a shelf before it is used, that page covers how the date code is tracked from reel to board.
Questions we get on this code
Is 150 V safe in this body? At the die level yes, and at the board level it depends on the gap and the environment. Keep the pad away from other traces and coat the assembly where the humidity is high.
How many vias under the pad? Enough that the thermal resistance from the pad into the plane is small against the 21 milliohm junction to case path. On two ounce copper, eight to twelve vias is the usual starting point for a few watts.
Can it be driven from 5 V? It can, but the resistance at 5 V is not the printed figure. Use a 10 V driver where the loss matters.
What should a purchase order carry? Part number, DFN8 5 by 6, and the tape and reel quantity. We confirm the reel size on the offer.