Contact Us

ISO1644DWR

Brand: Texas Instruments
Texas Instruments ISO1644DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO1644DWR — Power Management & Signal Chain | Superb Automation

ISO1644DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO1644DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO1644DWR: an I2C isolator with three extra channels for the rest of the bus

The ISO1644DWR isolates an I2C bus and adds three unidirectional CMOS channels that can carry GPIO or a serial peripheral interface across the same barrier. The two bidirectional lines, clock and data, handle up to 1.7 MHz and support the clock stretching that I2C peripherals rely on. Each channel has a logic input and an open drain output separated by a double capacitive silicon dioxide barrier, with 3.5 mA of sink capability on side one and 50 mA on side two.

The part is rated for hot plug insertion. SDA and SCL can be driven or pulled while the board is being inserted, and the barrier is rated to 5000 Vrms under UL 1577 in the 16 pin wide body and 3000 Vrms in the 8 pin body. The family is certified by VDE, UL, CSA, TUV and CQC for basic and reinforced insulation, and the barrier carries a projected lifetime beyond 100 years at 450 Vrms of working voltage in the small body, or 1500 Vrms in the wide body.

Key data for the ISO1644DWR

FunctionTwo bidirectional I2C channels plus three unidirectional channels for GPIO or a serial peripheral interface
RateBidirectional data to 1.7 MHz, unidirectional channels to 50 Mbps
OutputsOpen drain with 3.5 mA sink on side one and 50 mA sink on side two
Supplies3 V to 5.5 V on side one, 2.25 V to 5.5 V on side two
Isolation5000 Vrms in the wide body and 3000 Vrms in the small body per UL 1577
ImmunityAbout 100 kV per microsecond common mode transient immunity, 8 kV IEC contact discharge across the barrier

Body, marking and reel data

BodySOIC DW, 16 pins, 10.30 mm by 7.50 mm
Reel2000 pieces on a large reel on the plain and .A rows
MarkingISO1644 printed on the body
HandlingMoisture level 2, 260 C peak, one year floor life
Hot plugSDA and SCL survive insertion while the bus is active, which is the property a plug in module needs

Why the extra channels change the board

An isolated I2C segment usually carries more than clock and data. A sensor module has an interrupt line, a reset line and one or two address or enable pins. Building those with a second isolator costs another package, another set of decoupling capacitors and another barrier to certify. Three extra channels in the same body remove that second part, and because they are unidirectional they also work for a serial peripheral interface if the module uses one.

The hot plug behaviour is the second reason. A module that is inserted into a live rack pulls the bus lines through the connector pins in an arbitrary order, and a plain isolator can latch up on that sequence. This family is specified for the case, so the module can be added without dropping the segment.

Board points before the order

The first is the pull up resistors. Both sides need their own pull ups sized for the local rail and the bus capacitance, and the 3.5 mA sink on side one limits how low the resistor can go on that side. The second is the direction of the extra channels. The three GPIO channels in this member are unidirectional, so a bidirectional handshake line needs a different part in the family.

The third is the body choice. The 16 pin body gives 5000 Vrms and the 8 pin body gives 3000 Vrms, and the safety case decides which one is acceptable. The fourth is the supply sequencing: side two can start from 2.25 V, which is useful for a 2.5 V sensor rail, but a rail that is still ramping when side one is active will produce undefined states until both are stable.

I2C isolation and the pull up budget

An isolated I2C segment is quoted with the pull ups in mind, because the sink capability on each side sets the lowest usable resistor. Side one sinks 3.5 mA and side two sinks 50 mA, so a 2.2 k pull up on side one is close to the limit at 3.3 V while the same value on side two is comfortable. A customer who has copied a 1.5 k resistor from a non isolated bus will find the low level out of specification.

The second point is the extra channels. Three unidirectional channels cover interrupts, resets and enables, and a serial peripheral interface if the module uses one. A board that needs a fourth line or a bidirectional handshake needs a different member of the family, and that is worth settling before the board is routed rather than after.

Where the isolated segment is part of a medical instrument, the barrier context is on our medical device components page. Where the module is a long life product and the isolator is the part most likely to be discontinued, the route is on our component obsolescence management page.