SN65LVDS93AIDGGRQ1
Product Specifications
SN65LVDS93AIDGGRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LVDS93AIDGGRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LVDS93AIDGGRQ1: 28 bits of display data over four LVDS pairs
The SN65LVDS93AIDGGRQ1 is a FlatLink transmitter that loads 28 data bits plus a clock into four 7 bit shift registers and drives them out over four LVDS data pairs plus a clock pair. A pixel clock of 10 MHz to 135 MHz gives a transfer rate of 135 megapixels per second, which covers resolutions from HVGA up to HD without compression artifacts, and the serial side meets the ANSI EIA/TIA-644 electrical specification.
The parallel side accepts 1.8 V to 3.3 V tolerant inputs, so a low voltage application processor can drive it without a level translator, and the clock edge used to load the registers is selectable, which lets a board keep the same part when the processor changes its output edge. Typical consumption is 170 mW at 75 MHz and below 1 mW when disabled, and the device supports spread spectrum clocking so the pixel clock can be modulated for emissions compliance.
Key data for the SN65LVDS93AIDGGRQ1
| Function | 28 data bits plus clock in, four data pairs plus clock out, four 7 bit shift registers |
| Rate | Pixel clock 10 MHz to 135 MHz, transfer rate 135 megapixels per second |
| Inputs | 1.8 V to 3.3 V tolerant LVTTL data inputs, selectable rising or falling clock edge |
| Supply | 3.3 V single rail, 170 mW typical at 75 MHz, below 1 mW disabled |
| ESD | 5 kV human body model on the device pins |
| Timing | Input clock multiplied by seven for the serial unload, output clock equal to the input clock |
Body, marking and reel data
| Body | TSSOP DGG, 56 pins, 14.00 mm by 6.10 mm, or the 7.00 mm by 4.50 mm BGA junior body |
| Reel | 2000 pieces on a large reel on the DGGR rows, 35 pieces in a tube on the DGG rows |
| Marking | LVDS93A printed on the orderable rows |
| Handling | Moisture level 2, 260 C peak, one year floor life |
| Temperature | Minus 40 C to 85 C, which is the industrial window of the A revision |
Where 28 bits is the requirement rather than a luxury
An 8 bit per colour panel with three colours and four control lines needs 28 conductors, and a 24 bit panel with the same controls does not fit the 21 bit transmitter. That is the boundary between this part and the smaller FlatLink device, and it is the reason a display upgrade from XGA to full HD usually changes the transmitter as well as the panel.
The 1.8 V tolerant input is the second reason the part survives in new builds. Processors have moved their display ports down to 1.8 V while panels have stayed on 3.3 V receivers, and a transmitter that accepts the lower level directly removes a level shifter from the board and a set of timing uncertainties from the bring up.
Ordering and second source questions
The orderable table prints SN65LVDS93ADGGR at 2000 pieces on a large reel with a Level-2 moisture rating and a marking of LVDS93A, and it prints SN65LVDS93ADGG at 35 pieces in a tube. The catalogue string on this page carries the AI letters and a Q1 suffix, and neither appears as a published row in this revision. The A is the revision, the I is the industrial window, and the Q1 is the automotive qualifier, so a buyer should confirm which of the three the line actually needs rather than assume all three are in the box.
The second question is the deserialiser. The receiver has to match the four pair mapping and the clock recovery of this transmitter, and a panel with an integrated receiver expects exactly that. The third is the tube versus reel decision: a prototype that takes 35 pieces in a tube will not feed a pick and place line without a tube feeder.
Display transmitters on a long production life
A 28 bit transmitter is tied to a processor family and a panel, and both of those change more slowly than the silicon. The practical risk is that the transmitter is discontinued while the panel is still available, which leaves a board that cannot be built. That is why this family is quoted with a production life statement and, where the customer asks, with a stocking plan that covers the remaining build.
The packing follows the same pattern as the smaller part: 2000 pieces on a large reel and 35 pieces in a tube. A display assembly line takes the reel, and the tube is enough for a first article run. Because the part sits on a flex or a small board, the reel is often consumed by a subcontractor rather than by the end customer, and the date code and the reel label travel with the goods.
Where a display board is being kept in production past the life of the original processor, the sourcing route is on our OEM procurement page. Where the panel driver is the part that is disappearing, the alternative path is on our obsolete part cross reference hub.