Contact Us

SN65LVDS31NSR

Brand: Texas Instruments
Texas Instruments SN65LVDS31NSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDS31NSR — Power Management & Signal Chain | Superb Automation

SN65LVDS31NSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDS31NSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDS31NSR: four LVDS drivers in a 16 pin SOP

The SN65LVDS31NSR is a quad differential driver built to the ANSI TIA/EIA-644 electrical specification. Each of the four current mode outputs delivers at least 247 mV into a 100 ohm load when enabled, with 350 mV typical, and the output edges rise and fall in about 500 ps at 400 Mbps. Propagation delay is 1.7 ns typical, and each driver burns about 25 mW at 200 MHz, which is why the family is used wherever a differential clock or data fan out has to be cheap in power.

The driver outputs go high impedance when the part is disabled or when the supply is at 0 V, so several cards can share a bus and an unpowered card does not clamp it. Bus terminals are protected beyond 8 kV of discharge. The pinout is compatible with the AM26LS31, the MC3487 and the A9638, which is the reason this part keeps appearing in refresh projects that started life on a 5 V differential driver.

Key data for the SN65LVDS31NSR

FunctionFour independent differential drivers with enable inputs, one direction only
Rate400 Mbps, with 500 ps typical output rise and fall times
Levels350 mV typical output into a 100 ohm load, 247 mV minimum when enabled
Delays1.7 ns typical propagation delay per driver
Power3.3 V supply, about 25 mW per driver at 200 MHz
ProtectionBus terminal ESD beyond 8 kV, high impedance outputs when disabled or when VCC is 0 V

Body, marking and reel data

BodySOP NS, 16 pins, 10.30 mm by 5.30 mm, with SOIC and TSSOP options in the same group
Reel2500 pieces on a large reel, 330 mm carrier, on the plain and .B rows
MarkingLVDS31 printed on the body
HandlingMoisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to 85 C

Fan out, clock distribution and the 5 V replacement case

Four drivers in one body is the natural shape for a clock fan out on a backplane or a data distribution board, where one source feeds several destinations and each branch needs its own enable so a faulty card can be isolated. The high impedance state is what makes that isolation safe: pulling the enable low removes the driver from the bus without adding a series switch.

The replacement case is just as common. Boards that were laid out around a 5 V differential driver can often take this part with a supply change alone, because the pinout matches, and the lower swing then cuts the power and the emissions. What does not carry over is the receiver side: this is a driver only, and a link that also needs to listen requires a receiver part in the same family.

Points to confirm before ordering

First, whether the link is point to point or multi drop. The 100 ohm load rating assumes a single terminated pair, and a multi drop bus needs the M-LVDS family with a 30 ohm rating instead. Second, whether all four drivers are needed. A two driver version sits in the same group with the same electricals.

Third, the package. The NS body is a 5.3 mm wide SOP, and a board that was drawn for a narrow SOIC will need a footprint change even though the pinout matches. Fourth, the grading: this row is industrial, and the space grade members of the family carry a different part number and a different screening record.

Fan out parts and the reel behind them

A quad driver is usually bought once per board rather than once per link, so the annual quantity follows the board build and not the channel count. That makes the reel size less important than the availability of the die, and this family has stayed in production for a long time because it serves both the telecom backplane market and the refresh market for 5 V differential drivers.

When a customer asks for this part as a replacement for a 5 V device, we ask for the receiver at the far end before we confirm the order. A driver change without a receiver change produces a link that looks correct on a meter and fails on a protocol analyser, because the far end is looking for a swing that is no longer there. The quote then covers both ends of the link rather than one line of the bill of materials.

For a cross reference against a 5 V driver, the electrical comparison method is on the pin to pin cross reference page. Where a line is being kept alive past the original vendor status, our obsolescence route is on our component obsolescence management page.We also confirm the carrier width, because the NS body needs a 16 mm pocket tape while the TSSOP body of the same family runs on 12 mm, and a feeder loaded for one will not take the other.