Contact Us

SN65LVDS179DR

Brand: Texas Instruments
Texas Instruments SN65LVDS179DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDS179DR — Power Management & Signal Chain | Superb Automation

SN65LVDS179DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDS179DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDS179DR: one LVDS driver and one receiver for a two way link

The SN65LVDS179DR is the smallest member of the LVDS179 group: a single differential driver and a single differential receiver in an eight pin package, wired so that the link can run in both directions over two pairs. It meets the ANSI TIA/EIA-644-1995 electrical specification, delivers a minimum differential output of 247 mV into a 100 ohm load and accepts input differences down to 100 mV, which is the margin the standard requires for a link with up to 1 V of ground potential difference between the two ends.

Full duplex signalling reaches 150 Mbps on this member, with 350 mV of typical output swing. The driver propagates in 1.7 ns and the receiver in 3.7 ns, and the two blocks dissipate 25 mW and 60 mW respectively at 200 MHz. Bus pins survive 12 kV of discharge, the LVTTL inputs accept 5 V levels on a 3.3 V rail, and the receiver holds a high input impedance when the supply falls below 1.5 V so a powered down board does not load a live pair.

Key data for the SN65LVDS179DR

FunctionOne driver and one receiver, full duplex over two pairs, eight pins
RateFull duplex signalling up to 150 Mbps, with 400 Mbps available in the wider members of the group
Levels247 mV minimum output into 100 ohm, 350 mV typical, 100 mV receiver sensitivity
DelaysDriver 1.7 ns typical, receiver 3.7 ns typical
Power3.3 V supply, 25 mW driver and 60 mW receiver at 200 MHz
Protection12 kV bus pin ESD, open circuit failsafe, receiver high impedance below 1.5 V supply

Body, marking and reel data

BodySOIC D, 8 pins, 4.9 mm by 3.91 mm, with a VSSOP DGK option in the same group
Reel2500 pieces on a large reel on the plain, .B and G4 rows
MarkingS79 on the plain row, and the G4 row prints DL179
HandlingMoisture level 2, 260 C peak, one year floor life, so a bake applies after the floor life is exceeded
TemperatureMinus 40 C to 85 C

Where one pair each way is the right size

A camera head that sends video one way and takes a trigger the other way, a sensor module that streams samples and accepts a configuration word, and a board to board link inside an instrument all share the same shape: two directions, modest rate, short distance. The four channel parts are wasted on that link, and the eight pin part keeps the connector to two pairs plus ground.

The failsafe behaviour decides how the link behaves at power up. The receiver output is defined when the input is open, so a cable that is unplugged reads as a known state instead of oscillating. The high impedance input below 1.5 V matters in a hot swap shelf, where one card can be unpowered while its neighbours keep talking.

Checks before this code goes on a purchase order

The rate is the first check. This member is the 150 Mbps full duplex part, and a link that needs 400 Mbps needs the four channel member with the same electricals, not a faster clock on this one. The second is the loading: the standard allows a single termination at the receiver, and a doubly terminated bus needs a driver with more current, which is a different family.

The third is the moisture level. The plain row carries Level-2 with a one year floor life, so a reel that has been open on a shelf past that date needs a bake before reflow, and the production plan has to allow for it. The fourth is the marking: two strings are printed for the same die, so an inspection sheet that lists a single expected code will create false rejections.

Ordering the eight pin LVDS pair

The eight pin part is bought in small quantities more often than the four channel parts, because it sits on a module rather than on a backplane card. A module build of two hundred units takes less than a tenth of a 2500 piece reel, so the practical question is whether the assembler wants a partial reel, a cut tape, or a full reel held as stock. We quote all three and state the floor life clock on each.

The moisture level on this row is Level-2 with a one year floor life, which is longer than most builds need and shorter than a shelf stocked for a spares programme. A reel that has been open for two years needs a bake before reflow, and the bake is a documented step rather than an improvisation. For long life products we recommend buying the full reel and storing it sealed, with the date code recorded at goods in.

Where the part is being cross referenced against an older interface device, the procedure is on our drop in replacement checklist. Where date code control on a mixed reel matters, our handling note is on our date code management page.