VBGQA1101N
Product Specifications
VBGQA1101N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQA1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQA1101N: 100 V and 6 milliohm in a DFN 5 by 6
The VBGQA1101N is an N channel MOSFET in the DFN 5 by 6 body, printed at 100 V drain to source with a 175 C junction limit. On resistance is 6 milliohm at a 10 V gate and 8 milliohm at 4.5 V, with 65 A at a 25 C case and 30 A at 100 C. The vendor marks it with SGT technology, which in practice means a shielded gate trench die with a low figure of merit, and the numbers support that: 6 milliohm at 100 V is a class of part that did not exist in a 5 by 6 body a decade ago.
The body is the bottom side drain pad with the gate and source on the top, so the thermal path is through the board and the solder joint rather than through a lead frame. That makes the part attractive for a dense 48 V or 60 V rail where a TO-252 would be too tall, and it makes the copper area under the pad the first thing to check in any review. The sheet gives 0.85 C per watt typical and 1.1 C per watt maximum junction to case, and 40 to 50 C per watt junction to ambient depending on the copper.
Ratings at a glance
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 6 milliohm at 40 A |
| On resistance at 4.5 V gate | 8 milliohm at 20 A |
| On resistance at 125 C | 8 milliohm at 20 A |
| On resistance at 175 C | 12 milliohm at 20 A |
| Continuous drain current | 65 A at 25 C case, 30 A at 100 C case |
| Pulsed drain current | 255 A |
| Continuous source current, diode | 55 A |
| Single pulse avalanche energy | 110 mJ into 0.1 mH |
| Power dissipation | 136 W at 25 C case, 3 W at 25 C ambient |
| Junction to case | 0.85 C per watt typical, 1.1 maximum |
| Gate threshold voltage | 1 V minimum, 2 V typical, 3 V maximum |
| Input capacitance | 2300 pF |
| Total gate charge | 70 nC maximum, printed in the maximum column |
| Body diode reverse recovery | 135 ns at 20 A, 100 A per microsecond |
The rows that change a decision
The three resistance rows at 25 C, 125 C and 175 C read 6, 8 and 12 milliohm. That is a much flatter curve than a trench part of the previous generation, and it is the reason this die can be run hot without doubling its conduction loss. At 30 A the difference between 6 and 12 milliohm is 2.7 W against 5.4 W in one device, which is the difference between a passive heatsink and a fan in a small enclosure.
The threshold window is 1 V minimum, 2 V typical and 3 V maximum, so the part is fully on at 4.5 V and is not intended for a 2.5 V logic rail. Gate charge of 70 nC maximum with 2300 pF of input capacitance means the driver has to deliver real current at 100 kHz and above: 70 nC at 100 kHz is 7 mA of average gate current, which any driver handles, but the peak current during the 20 ns edge is several amps and the gate loop has to be short.
The diode recovery is 135 ns at 20 A with 100 A per microsecond, and the forward voltage is 1 V typical and 1.5 V maximum at 20 A. That is a slow diode for a 100 V part, so a hard switched half bridge at high frequency will pay for it in the opposite switch. Where the topology allows, a sync rectifier with a short dead time or a resonant stage is the better home for this die than a 200 kHz hard switched bridge.
The dissipation rows deserve attention: 136 W at a 25 C case but only 3 W at a 25 C ambient, with 3.8 W listed for a ten second pulse. Those two numbers are the whole thermal story. A part that is a 136 W device on a cold plate is a 3 W device on a board in still air, and the copper under the pad is what moves it from one column to the other.
Where a 100 V DFN earns its place
Telecom and server boards use this class for a 48 V hot swap or a 48 V to 12 V stage, where the 100 V rating covers the 57 V maximum of a PoE feed and the transient of a backplane. Battery powered equipment with a 60 V or 72 V pack uses it as a disconnect or a precharge switch, and the low profile body fits under a daughter card that has 3 mm of clearance. Motor drives in the 48 V class use it in a three phase bridge, and the 255 A pulse rating covers the stall current of a small pump or fan.
Because the part is a bottom side drain device, it also suits a double sided assembly where the heat can be pulled into an aluminium base or a thermal pad. In that arrangement the junction to case figure of 0.85 C per watt is the one that matters, and the board becomes the heatsink. In a convection cooled plastic case the part still works, but at a fraction of the headline current, and the ambient derating curve in the sheet is the honest guide.
Sourcing a 100 V DFN and checking the alternative
The DFN 5 by 6 pad is shared by a large number of parts at 60, 80 and 100 V, and the pad alone says nothing about which one is fitted. Our power management cross reference compares the voltage class, the resistance at 4.5 V and the gate charge first, because those three decide whether a drop in part will survive the same switching node. The pinch point on this body is usually the gate pad position rather than the drain pad, and a part with the gate on the other side will not fit at all.
For a qualified product, the verification route in how to verify a drop in replacement covers the tests that separate a good alternative from a plausible one: a switching waveform at the real load, a thermal soak with the case instrumented, and a short circuit event to confirm the current limit and the avalanche behaviour. We also keep the incoming inspection plan for this family, which samples on resistance and gate threshold from each lot before the reel goes to the line.
Questions from buyers on this code
Buyers ask whether 65 A is available in a 5 by 6 body. It is, at a 25 C case with the pad soldered to a large copper area, and the same board in still air carries about 8 A before the junction reaches 150 C, which is why the vendor prints both a 136 W and a 3 W dissipation row. The second question is whether the 4.5 V column is usable. It is, at 8 milliohm, but the gate charge is the same 70 nC, so the drive energy does not fall with the lower gate voltage and a small driver can still be marginal at high frequency.
The third question is about the source current rating of 55 A, which is the diode conduction path and is lower than the 65 A channel rating. A synchronous stage that leans on the body diode during a long dead time should be checked against 55 A and against the 135 ns recovery, not against the channel figure. The fourth is avalanche: 110 mJ into 0.1 mH is a single pulse at 25 C, and it is a real protection for a cable or a motor, but it is not a licence to run without a clamp on a hot board.
On supply, we quote this code per reel with the date code on the label and a sample resistance record per lot. Where a customer needs a tighter window than the sheet guarantees, the honest route is a selection step agreed before the order, not a hope that the next reel matches the last one.