VBGM1803
Product Specifications
VBGM1803
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGM1803 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGM1803: an 80 V 180 A switch in the TO-220 body
The VBGM1803 is an N channel trench MOSFET in the TO-220 outline, printed at 80 V with plus or minus 20 V on the gate and a 150 C junction. On resistance is 3 milliohm at a 10 V gate with 30 A flowing and 4 milliohm at 4.5 V, continuous drain current is 180 A with the case at 25 C and 140 A with the case at 70 C, and the pulsed rating is 540 A for 100 microseconds. Gate charge is 48 nC typical against 8600 pF of input capacitance, single pulse avalanche energy is 820 mJ at 80 A peak from 0.5 mH, and the body diode recovers in 25 ns typical with no maximum printed.
The TO-220 body is the one that still dominates prototypes and low volume production, because it can be screwed to a bracket without a reflow process. A part with 3 milliohm and 180 A in that body is a serious switch for a 48 V or 60 V high current path, and the thermal rows on this sheet are the ones a mechanical engineer will want to see before a bracket is drawn.
The ratings a buyer checks first
| Drain to source voltage | 80 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A, 25 C | 3 milliohm |
| On resistance at 4.5 V gate, 30 A, 25 C | 4 milliohm |
| Continuous drain current, case at 25 C | 180 A |
| Continuous drain current, case at 70 C | 140 A |
| Pulsed drain current for 100 microseconds | 540 A |
| Single pulse avalanche energy and current | 820 mJ from 0.5 mH, 80 A peak |
| Power dissipation, case at 25 C and 100 C | 300 W and 150 W |
| Junction to ambient on a one inch pad, junction to case | 40 and 0.5 C per watt |
| Gate threshold voltage at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Drain leakage at 80 V, 25 C, 125 C and 150 C | 1 microamp, 150 microamp and 5 mA maximum |
| Input, output and reverse transfer capacitance | 8600, 246 and 21 pF at 80 V |
| Total gate charge and gate drain charge | 48 and 16.9 nC typical |
| Turn on delay and rise time | 26 and 105 ns typical |
| Turn off delay and fall time | 35 and 80 ns typical |
| Body diode forward drop at 10 A | 0.8 V typical, 1.2 V maximum |
| Body diode reverse recovery | 25 ns typical, no maximum printed |
Reading the electrical table instead of the front page
One hundred and eighty amps through 3 milliohm is 97 W, so the same arithmetic as its 100 V neighbour applies: the die is 49 C above the case at that current, and the case has to be cooled. On a one inch pad the honest continuous current is about 31 A, where the loss is 2.9 W and the junction sits 115 C above a 60 C ambient inside a 150 C limit. The 180 A row is a bracket or heatsink figure, and the TO-220 tab is there to make that possible.
What makes this part interesting is the gate charge. At 48 nC typical it carries less than half the charge of the 100 V part with the same resistance, and the input capacitance of 8600 pF is close to the same, which suggests a die with a thicker gate oxide and a flatter transfer characteristic. The rise time of 105 ns on the other hand is slow: four times the 100 V part with a smaller charge. Slow turn on with 8600 pF of input capacitance at 80 V is a deliberate trade, and it shows up as a lower peak current during a switching transient and as an easier diode recovery for the opposite device.
An 80 V rating in a 48 V system leaves limited margin. A 48 V rail with a 20 per cent transient reaches 58 V, and the leakage spike of a switching node adds another 10 V to 15 V on top, which puts the drain near 73 V. That is inside 80 V but not by much, and a buyer with a long cable or a high leakage transformer should be checking the spike on a working board rather than assuming the rating covers it.
The body diode publishes 25 ns of recovery with no maximum and no recovered charge row at all. For a bridge or a synchronous rectifier that is the figure that sets the dead time and the loss in the opposite device, so the missing maximum is a real gap. In a low frequency motor drive it matters less, because the dead time is set by the driver and the diode loss is absorbed, but in a synchronous buck at 50 kHz a buyer should ask for the curve rather than plan on 25 ns.
Where an 80 V TO-220 device earns its place
The first use is the low side switch in a 48 V motor drive, where the case can be bolted to a bracket and the 540 A pulse covers a locked rotor. The second is a battery disconnect in a 60 V pack, where 80 V gives just enough headroom for the charger transient and the avalanche energy of 820 mJ covers a load dump with a clamp.
The third is an inverter leg in a small uninterruptible supply at 48 V, where the switching frequency is 20 kHz, the current is high and the TO-220 body can be mounted to the same bracket as the transformer. The fourth is a class D amplifier stage at 60 V, which the vendor lists among the applications, where the slow turn on is actually welcome because it keeps the radiated spectrum inside the limits.
What the part is not is a 48 V hot swap controller. A hot swap event puts the switch into linear operation for milliseconds, and 30 A at 80 V is 2.4 kW of dissipation, far outside the safe operating area of any 3 milliohm die. A hot swap function needs a part with a published linear mode curve and an active current limit, not a switching device.
Sourcing notes and the second source question
Second sourcing a TO-220 power switch is easier mechanically than any surface mount body, because the outline is standardized, and harder electrically, because the junction to case figure and the mounting method decide the usable current. The power management cross reference keeps the thermal pair in the same row as the resistance so a candidate is compared on the whole set rather than on the headline.
The other half is the solderability of the tab and the flatness of the back surface: a TO-220 with a rough tab needs more thermal compound and a higher mounting force, and on a bracket with several devices the difference shows up as one hot part. Our incoming inspection plan page describes the dimensional checks that catch this before assembly.
Where the part is being qualified as a second source on an existing bracket, the how to verify a drop in replacement page covers the bench sequence, including the avalanche and recovery checks that a datasheet comparison alone cannot settle.
Questions we answer before a reel is booked
The first question is the voltage margin on a 48 V rail. With 80 V of blocking and a spike that can reach 73 V, the margin is thin, and a buyer with a long motor cable should either clamp the node or move to a 100 V part at a slightly higher resistance. The 100 V part in the same catalogue carries the same 3 milliohm, which makes the choice easy.
The second is the current on the bracket. The 180 A row assumes a 25 C case, which a bracket in still air will not hold at that loss. A practical figure for a bolted TO-220 with a modest heatsink is 40 A to 60 A continuous, and the bracket temperature is the number to measure rather than the case rating to quote.
The third is the gate charge and the drive. At 48 nC typical and no printed maximum, a driver with 1 A of peak current turns the part on in about 50 ns, and the 105 ns rise time in the table is the die response rather than the driver limit. A slow rise into a 540 A pulse capability is a good combination for a motor drive and a poor one for a converter that needs a clean edge at 200 kHz.