VBGL7101
Product Specifications
VBGL7101
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGL7101 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGL7101: a 100 V die at 1.2 milliohm in a seven lead TO-263
The VBGL7101 is an N channel trench MOSFET in the seven lead TO-263 outline, printed at 100 V with plus or minus 20 V on the gate. On resistance is 1.2 milliohm at a 10 V gate and 2.0 milliohm at 4.5 V, continuous drain current is 250 A with the case at 25 C and 200 A with the case at 70 C, and the pulsed rating is 750 A for 100 microseconds. Gate charge is 60 nC typical against an input capacitance of 8200 pF, single pulse avalanche energy is 1000 mJ at 110 A peak from 0.5 mH, and the diode recovers in 16 ns typical.
A 1.2 milliohm resistance at 100 V is close to the limit of what a silicon die can do at that blocking voltage, and everything else on the sheet follows from the die size: 8200 pF of input capacitance, 60 nC of gate charge, and a body that has to be a seven lead TO-263 to carry the current out of the source. This is a part for a high current low frequency path, not for a switching converter that runs fast.
The ratings a buyer checks first
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A, 25 C | 1.2 milliohm |
| On resistance at 4.5 V gate, 20 A, 25 C | 2.0 milliohm |
| Continuous drain current, case at 25 C | 250 A, package limited |
| Continuous drain current, case at 70 C | 200 A |
| Pulsed drain current for 100 microseconds | 750 A |
| Single pulse avalanche energy and current | 1000 mJ from 0.5 mH, 110 A peak |
| Power dissipation, case at 25 C and 100 C | 300 W and 150 W |
| Junction to ambient on a one inch pad, junction to case | 40 and 0.5 C per watt |
| Gate threshold voltage at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Drain leakage at 80 V, 25 C, 125 C and 150 C | 1 microamp, 150 microamp and 5 mA maximum |
| Input, output and reverse transfer capacitance | 8200, 246 and 21 pF at 100 V |
| Total gate charge and gate drain charge | 60 and 16.9 nC typical, 80 nC maximum |
| Turn on delay and rise time | 20 and 25 ns typical |
| Turn off delay and fall time | 12 and 10 ns typical |
| Body diode forward drop at 10 A | 0.8 V typical, 1.2 V maximum |
| Body diode reverse recovery and recovered charge | 16 ns and 0.9 microcoulomb typical |
Reading the electrical table instead of the front page
Two hundred and fifty amps through 1.2 milliohm is 75 W. With a junction to case figure of 0.5 C per watt the die sits 37 C above the case, which is survivable only if the case is held near 25 C by a heatsink or by a large copper plane bonded to the tab. On the one inch pad that the ambient row assumes, the same 75 W against 40 C per watt is impossible by a factor of fifty. The honest continuous figure on a plain board is about 49 A, where 2.9 W of loss lifts the junction 115 C above a 60 C ambient, and everything between that and 250 A requires a real thermal path that the board has to provide.
The 1.2 milliohm row is measured at 30 A, one eighth of the headline current, which is how the vendor keeps the measurement out of the self heating region. At 250 A the die would dissipate 75 W during the measurement and the reading would drift, so the quoted figure describes the cold die rather than the working one. A buyer planning a 100 A path should also ask for the 125 C resistance curve, because a 100 V trench die typically doubles between 25 C and 125 C and the sheet prints no hot row at all.
The temperature rows contradict each other, which is worth knowing before a qualification document quotes one of them. The feature line states a maximum junction of 150 C, the absolute maximum table prints minus 55 to plus 175 C, and the leakage rows are specified at 150 C. The conservative reading is to plan the thermal path to 150 C and treat the 175 C figure as the survival limit rather than an operating point.
The gate charge and the switching times are consistent with each other: 60 nC typical against a 16.9 nC gate drain charge, a 20 ns turn on delay and a 25 ns rise time into a 1.66 ohm load at 100 V. At 100 kHz the drive cost is 6 mA of average gate current and the input capacitance has to be charged once per cycle, so this is a part for a 20 kHz to 50 kHz path or for a static switch. Where the vendor prints a maximum column the numbers are 80 nC and 23 ns, small enough differences that a driver sized on the typical is unlikely to be far wrong.
Where a 100 V sub two milliohm device earns its place
The first use is battery disconnect and reverse polarity protection on a 48 V pack, where the switch sits in the negative or positive rail and carries the full load current for hours. At 1.2 milliohm and 60 A the loss is 4.3 W, which is why the seven lead body exists: the source current has to leave through several leads, and a single lead tab would add more resistance than the die.
The second is a high current ORing path between a battery and a mains supply, where two of these parts back to back block in both directions and the body diode drop is bypassed by the channel once the gate is on. The third is a low frequency inverter leg at 48 V, where the switching loss at 20 kHz is acceptable and the conduction loss dominates the budget.
What the part is not is a 200 kHz synchronous buck switch. At 8200 pF of input capacitance and 60 nC of gate charge the drive loss alone is several watts at that frequency, and the rise and fall times of 25 ns and 10 ns against a 5 microsecond period leave little room for a soft switching scheme. A buyer who needs both the low resistance and the frequency should be looking at a 40 V part, which reaches the same resistance on a much smaller die.
Sourcing notes and the second source question
For a part at this current level the second source question is a mechanical one before it is an electrical one. The seven lead TO-263 has a specific lead frame, and a candidate from another vendor can be electrically identical and still not fit a footprint laid out for the original lead pitch. The pin to pin cross reference keeps the lead frame dimensions in the same row as the resistance, so the mechanical check happens before the sample order.
The electrical comparison has to include the capacitance, because a 1.2 milliohm die and a 2 milliohm die can be the same silicon area with different gate oxide, and the drive requirement changes accordingly. The power management cross reference carries the input capacitance and the gate charge beside the resistance for that comparison.
On supply, a part this large is usually built in one or two fab lines and has a longer cycle time than the small signal devices around it, so a buyer with a production ramp should carry a second approved part or a buffer stock. Our safety stock planning page sets out how the buffer is sized against the cycle time and the forecast.
Questions we answer before a reel is booked
The first question is what current can be carried on the actual board. The answer comes from the pad area, not from the ratings page: 49 A on a one inch pad, more with a copper bar or a heatsink, and 250 A only with a case held at 25 C. A buyer who plans 150 A continuously should be prepared to show the thermal path.
The second is the gate drive. The threshold window reaches 4.5 V and the 4.5 V resistance row is 67 per cent higher than the 10 V row, so a logic level drive at 5 V is not the intended condition. Ten volts from a dedicated driver is the right answer, and the 80 nC maximum gate charge is what that driver has to deliver.
The third is the junction temperature basis. With three different numbers on the sheet, a qualification plan should state which one it uses. Our usual reading is 150 C of operating junction with the 175 C row treated as a survival rating, and the leakage rows at 150 C support that reading.