VBGE1402
Product Specifications
VBGE1402
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGE1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGE1402: a 40 V, 110 A N channel in TO-252
The VBGE1402 is a single N channel MOSFET in the TO-252 body, printed at 40 V drain to source and plus or minus 20 V on the gate, with 2 milliohm at a 10 V gate and 3 milliohm at 4.5 V. It carries 110 A at a 25 C case and 80 A at 70 C, with a 330 A pulsed rating over 100 microseconds. The vendor files it under power supplies, synchronous rectification, motor drive, inverters, solar micro inverters and class D audio, which is a broad list for one part and tells the buyer that this is a general purpose low voltage switch rather than an application specific device.
What makes the part interesting is the ratio of current to package. The TO-252 is a three lead surface mount body with a drain tab, so the thermal path runs through the tab into the board rather than through a heatsink. With 1.3 C per watt junction to case and 40 C per watt junction to ambient on a one inch board, the copper area under the tab is doing most of the work. A board that gives the tab a full square inch of copper on two layers behaves like the data sheet, and one that necks the copper down does not.
Ratings and the numbers behind them
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 2 milliohm |
| On resistance at 4.5 V gate | 3 milliohm at 35 A |
| Continuous drain current | 110 A at 25 C case, 80 A at 70 C case |
| Pulsed drain current, 100 microsecond | 330 A |
| Single pulse avalanche energy | 600 mJ into 0.5 mH |
| Avalanche current | 62 A |
| Power dissipation | 150 W at 25 C case, 57 W at 100 C case |
| Junction to case | 1.3 C per watt |
| Junction to ambient, one inch board | 40 C per watt |
| Gate threshold voltage | 2.5 V minimum, 4.5 V maximum |
| Total gate charge | 40 nC typical |
| Input capacitance | 7600 pF |
| Body diode reverse recovery | 40 ns typical, 0.9 microcoulomb typical |
Reading the rows rather than the front page
The threshold window on this part is wide: 2.5 V minimum and 4.5 V maximum at 250 microamp. A 4.5 V gate drive therefore sits at the top of the threshold window on a worst case device, which means the part is on but not comfortably so, and a 10 V drive is the honest choice for a hard switched stage. This is the single most common mistake we see with this family: a 5 V rail used as gate drive because the front page says 4.5 V, followed by a batch that runs hot at cold start.
The gate charge of 40 nC typical against 7600 pF of input capacitance and 21 pF of reverse transfer tells a story about the die: it is a large area part with modest feedback capacitance, so it switches quickly for its size and is reasonably easy to keep quiet. Rise time is 128 ns typical and fall 85 ns in the sheet test, measured at 40 V into 1.66 ohm with a 10 V drive and a 1 ohm gate resistor, which is a slow, controlled edge rather than a racing one. Turn off delay is 37 ns typical, close to turn on delay, so the dead time can be kept short.
Reverse recovery is the number that decides whether this part can be the low side of a half bridge. The body diode takes 40 ns to recover, with 0.9 microcoulomb of recovered charge and an 11 A peak reverse current at 30 A forward and 100 A per microsecond. In a hard switched half bridge at 100 kHz that charge is a real loss in the opposite switch, and it has to be counted in the loss budget rather than discovered on the thermal camera.
The avalanche rating is unusually generous: 600 mJ into 0.5 mH with 62 A of avalanche current. That covers the turn off transient of a motor or a long cable without an external clamp in most cases. It is a single pulse figure at 25 C, and it derates with junction temperature, so a hot board has far less headroom than the number suggests.
Where the part is used
At 40 V and 2 milliohm, the natural home is a 12 V to 24 V bus: a synchronous rectifier on the secondary of an isolated converter, the low side of a non isolated buck, or a battery disconnect on a 24 V pack. Motor drives for fans, pumps and small traction use it as the low side switch in a three phase bridge, where the 330 A pulse rating covers the stall current without an oversized device. Solar micro inverters use the same body for the boost stage and the unfolding bridge.
Class D audio is listed by the vendor and is a good fit because the low on resistance keeps the idle loss down and the 40 V rating covers a 36 V rail with margin. In every one of these uses the deciding factor is not the current rating but the thermal path: the same part carries 110 A on a 25 C case and roughly 3 A in free air on a one inch board, and a product that runs continuously needs the copper area or a metal backed board.
Buying this code and proving the alternative
The TO-252 footprint is one of the most widely second sourced in the industry, which is both an advantage and a trap. Two parts can share the pad and differ in threshold, in gate charge and in the avalanche rating. Our power management cross reference keeps the comparison to the rows that change behaviour on a real board: threshold maximum, on resistance at 4.5 V, gate charge, reverse recovery charge and avalanche energy.
Where a customer wants a second source for a qualified product, the practical sequence is spelled out in how to verify a drop in replacement. For this body the tests that matter are a cold start at the lowest rated temperature, a full load thermal soak with the case thermocouple where the product actually mounts, and a short circuit or stall event to confirm the avalanche and current limit behaviour. We supply the part with the matching gate resistor and, where the customer asks, with a sample from the same date code as the production reel so the qualification and the build agree.
What buyers ask us about this part
The first question is whether 110 A is a real number. It is a case temperature figure limited by the package, not by the die, and the honest continuous rating in a convection cooled product is set by the copper and the ambient. The second is whether the part can be driven from a 4.5 V rail. It can be turned on, but the threshold maximum of 4.5 V means the worst case device is only just conducting, so a 10 V drive or a charge pump is the safer choice.
The third question is about paralleling. Two devices share current reasonably well at 2 milliohm because the resistance dominates the threshold spread, but the gate resistors should be separate so the two do not oscillate against each other, and the copper has to keep the two source paths symmetric. The fourth is the diode: 40 ns recovery is fast enough for most hard switched stages below 150 kHz, and above that the recovered charge should be measured rather than estimated.
On supply, this code comes on the standard TO-252 reel with the quantity and date code printed on the label, and we hold an incoming record that includes a sample on resistance check at 10 V and at 4.5 V. If a build needs a tighter resistance window than the sheet guarantees, that is a selection step rather than a purchase order note, and it has to be agreed before the reels are booked.