Contact Us

VBGA1156N

Brand: VBsemi
VBsemi VBGA1156N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGA1156N — Discrete & Power Semiconductors | Superb Automation

VBGA1156N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGA1156N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGA1156N: a 150 V N channel in an SOP-8 body

The VBGA1156N is an N channel super junction gate trench MOSFET in the SOP-8 outline, printed at 150 V with plus or minus 20 V on the gate and a 150 C junction. On resistance is 55 milliohm at a 10 V gate with 30 A flowing and 58 milliohm at 7.5 V, continuous drain current is 5 A with the case at 25 C and 4 A with the case at 70 C, and the pulsed rating is 15 A for 100 microseconds. Gate charge is 40 nC typical, and single pulse avalanche energy is 700 mJ at 60 A peak from 0.5 mH.

An SOP-8 part that blocks 150 V sits in a narrow slot. It is high enough in voltage to work on a 48 V rail with the transient margin a telecom or industrial supply needs, and small enough to be placed next to the controller instead of on a heatsink. The price is current: 5 A is the package limit, not a die limit, and the whole thermal story has to be read with that in mind.

The ratings a buyer checks first

Drain to source voltage150 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 30 A, 25 C55 milliohm maximum
On resistance at 7.5 V gate, 30 A, 25 C58 milliohm
Continuous drain current, case at 25 C5 A
Continuous drain current, case at 70 C4 A
Pulsed drain current for 100 microseconds15 A
Single pulse avalanche energy and current700 mJ from 0.5 mH, 60 A peak
Power dissipation rows as printed300 W with the case at 25 C, 150 W with the case at 100 C
Junction to ambient on a one inch pad, junction to case40 and 0.5 C per watt
Gate threshold voltage at 250 microamp2.5 V minimum, 4.5 V maximum
Gate body leakage at plus or minus 20 Vplus or minus 250 nA maximum
Drain leakage at 150 V, 25 C, 125 C and 150 C1 microamp, 150 microamp and 5 mA maximum
Total gate charge and gate drain charge40 and 16.9 nC typical, 96 nC maximum
Input, output and reverse transfer capacitance800, 246 and 21 pF at 20 V
Turn on delay and rise time21 and 105 ns typical
Turn off delay and fall time35 and 81 ns typical
Body diode reverse recovery and recovered charge20 ns and 0.9 microcoulomb typical

Reading the electrical table instead of the front page

The thermal rows on this sheet do not belong to an SOP-8. A junction to case figure of 0.5 C per watt and a dissipation of 300 W describe a TO-220 or a D2PAK tab, not a body whose eight leads are its only path to copper. The row that does describe this part is the junction to ambient figure of 40 C per watt on a one inch pad, and that row sets the real limit: at a 60 C ambient and a 150 C junction, 90 C of rise allows 2.25 W, which at 55 milliohm is 6.4 A. The 5 A current row is therefore the binding limit, and the thermal rows should be treated as an error in the document rather than as a thermal target.

Two other rows carry the same fingerprint. The gate charge is specified at 60 A of drain current on a part rated for 5 A continuous and 15 A pulsed, and the output and reverse transfer capacitances of 246 and 21 pF are identical to several other sheets in this catalogue at different voltages. Those are template values. The input capacitance of 800 pF and the 40 nC of gate charge are consistent with a small 150 V die, and a driver has to be sized on the 96 nC maximum rather than the 40 nC typical.

The switching rows are slow by modern standards and honestly so. A rise time of 105 ns typical and 206 ns maximum into a 1.66 ohm load at 30 V describes a die with 800 pF of input capacitance driven through 3 ohm of internal gate resistance. At 100 kHz that is 3.4 W of switching loss on a 400 mA gate drive, so the part is not a candidate for a high frequency converter. At 30 kHz to 50 kHz, which is where a 150 V flyback or a 48 V input forward converter usually runs, it is fine.

The body diode is the interesting row. A reverse recovery of 20 ns typical against 40 ns maximum, with 0.9 microcoulomb of recovered charge at 30 A and 100 A per microsecond, is fast for a 150 V part. In a discontinuous flyback the diode conducts the magnetizing current every cycle and a fast recovery keeps the turn on loss of the primary switch down. In a bridge it decides how much dead time is needed, and 20 ns means a very short one is possible.

Where a 150 V SOP-8 device earns its place

The first case is the primary clamp or the auxiliary switch in a 48 V input flyback, where 150 V covers the reflected voltage plus the leakage spike and 5 A covers a 100 W output at 6 A of primary current in discontinuous mode. The second is synchronous rectification on a secondary of 24 V or 28 V, where the peak voltage seen by the rectifier after the leakage ring is close to 150 V and a 100 V part would be punched through on a load transient.

The third case is a class D audio output stage at 48 V, which the vendor lists among the applications: the switching frequency is a few hundred kilohertz but the current per device is low, and an SOP-8 with 700 mJ of avalanche energy survives the inductive kick that a speaker cable can present. The fourth is a solar micro inverter, where the input is around 40 V and the boost stage sees 100 V to 150 V of ringing.

What the part is not is a load switch on a battery. With 5 A as a package limit and 55 milliohm of resistance, the loss at full current is 1.4 W in a body that can only remove it through eight leads. A DFN 5 by 6 part at a third of the resistance does the same job with a quarter of the heat, and the only reason to stay with an SOP-8 is an existing board and a qualified footprint.

Sourcing notes and the second source question

Second sourcing a 150 V SOP-8 is mostly a capacitance question, because the die that wins on resistance often loses on gate charge and the driver was chosen for the original part. Two candidates that both print 55 milliohm can sit ten nC apart, and at 50 kHz that difference shows up as a degree or two of junction temperature rather than as a failure. The power management cross reference puts the charge and the capacitance in the same table as the resistance so the comparison starts in the right place.

The second half is the footprint. An SOP-8 with a heat slug and an SOP-8 without one look identical on a drawing and behave completely differently when the board dissipates 1.4 W, so a drop in replacement has to be checked against the copper area on the actual board rather than against the body outline. Our how to verify a drop in replacement page lists the checks that catch this before the first reflow.

Where a buyer needs the part for a production build and the original vendor has moved to a newer die, the obsolete part cross reference hub is the place to start, because a part that is still listed but marked not recommended for new builds behaves like an obsolete one in a schedule.

Questions we answer before a reel is booked

The first question is whether 5 A is a die rating or a body rating. It is a body rating: the die is the same one that carries 15 A in a bigger package, and the SOP-8 cannot remove the heat. A buyer planning 4 A continuous should calculate 0.97 W of conduction loss against 40 C per watt, which is a 39 C rise and comfortable, and a buyer planning 5 A in a sealed box at 70 C ambient should not.

The second question is the power dissipation row. If a customer's qualification document quotes 300 W from the front page, the answer is that the row is a template error and the real limit is the 40 C per watt ambient figure. It is better to correct this in the test plan than to discover it in thermal cycling.

The third question is the gate drive. With a threshold window up to 4.5 V, a 5 V logic gate drive leaves no margin at the cold corner, and the 7.5 V resistance row exists precisely because many products drive from a 7 V to 8 V bias. Ten volts is the intended condition, and the 96 nC maximum gate charge is what the driver has to move at the switching frequency the topology requires.