Contact Us

VBFB1252M

Brand: VBsemi
VBsemi VBFB1252M is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBFB1252M — Discrete & Power Semiconductors | Superb Automation

VBFB1252M

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBFB1252M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBFB1252M: a 250 V N channel in TO-251 rated for a hot junction

The VBFB1252M is an N channel MOSFET in the TO-251 outline, the body also sold as the I-PAK, printed at 250 V from drain to source with plus or minus 20 V on the gate. On resistance is 0.176 ohm maximum at a 10 V gate with 8.4 A flowing, continuous drain current is 17 A with the case at 25 C and 11 A with the case at 100 C, the pulsed rating is 56 A, and the single pulse avalanche energy is 550 mJ from a 50 V rail into 4.5 mH at 14 A. The part is built on a planar process with a dynamic dV/dt rating and a repetitive avalanche rating rather than a trench process.

The title of the sheet calls it a 175 C MOSFET, and that is the claim a buyer has to check against the operating range, which reads minus 55 to plus 150 C. The 175 C in the title belongs to the die family and the 150 C row is the limit printed in the absolute maximum table, so the conservative reading is 150 C. Either way, a part that is specified hot and avalanche rated at 550 mJ is aimed at the motor drive and the offline switching market rather than at a logic level load switch.

The ratings a buyer checks first

Drain to source voltage250 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 8.4 A0.176 ohm maximum
Continuous drain current, case at 25 C and 100 C17 A and 11 A
Pulsed drain current56 A
Single pulse avalanche energy550 mJ from 50 V into 4.5 mH, 14 A peak
Repetitive avalanche current and energy17 A and 13 mJ
Power dissipation, case at 25 C125 W, 1.0 W per C derating
Junction to case, junction to ambient1.0 and 62 C per watt
Case to sink, flat and greased0.50 C per watt
Peak diode recovery dV/dt4.8 V per nanosecond
Gate threshold voltage2.0 V minimum, 4.0 V maximum
Total gate charge, gate source and gate drain charge68, 11 and 35 nC maximum
Input, output and reverse transfer capacitance1300, 330 and 85 pF
Turn on delay, rise, turn off delay and fall time11, 24, 53 and 49 ns typical
Internal drain and source inductance4.5 and 7.5 nH
Body diode forward voltage at 14 A1.8 V maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

Every charge row on this sheet is a maximum and none of them carries a typical, which is unusual and worth knowing. Gate charge is 68 nC, gate source 11 nC and gate drain 35 nC, all as maximum values, so the driver calculation uses 68 nC directly and there is no typical figure to be tempted by. The same pattern appears on the resistance: 0.176 ohm is printed as a maximum at 8.4 A, so a calculation that assumes 0.176 ohm at 25 C has already taken the worst case for that temperature and still has to scale for a 125 C junction, where the figure is roughly 1.7 times higher.

The avalanche numbers separate this part from the trench devices in the same band. A single pulse of 550 mJ from 50 V into 4.5 mH is a substantial energy, and there is a repetitive rating as well, 17 A and 13 mJ, which most consumer parts do not publish at all. In a motor drive with a clamped inductive load, or in a relay replacement that sees a cable kick, that rating is what keeps the part alive when the clamp is imperfect, and it is the row a buyer should compare before a substitution rather than the resistance.

The internal inductance rows are published, 4.5 nH on the drain and 7.5 nH on the source, which means the source lead is not a short circuit at the frequencies where a 250 V part switches. At a 20 A edge in 24 ns, 7.5 nH produces about 6 V of source bounce, which subtracts from the gate drive and slows the turn on. That is the reason a Kelvin source connection on the gate loop matters more on this body than on a smaller one.

The body diode is slow and the forward drop is high, 1.8 V maximum at 14 A with a recovery time of 250 ns typical and 500 maximum and a recovered charge of 2.3 microcoulomb typical and 4.6 maximum. On a bridge or a half bridge at 50 kHz that 500 ns worst case is 2.5 per cent of the period, which is a diode that needs a dead time and a snubber rather than a diode that can be ignored, and the 4.8 V per nanosecond recovery dV/dt limit is the constraint that a fast switching leg will hit first.

Where a 250 V N channel in TO-251 earns its place

The first case is a motor drive or a relay replacement on a 110 V to 160 V DC link, where 250 V covers the commutation overshoot and the 550 mJ avalanche rating covers the cable inductance. The second is a flyback or a forward converter on a 120 V rail, where 17 A of case rated current and 125 W of case dissipation suit a 50 W to 100 W converter on a small heatsink. The third is a battery path in a 96 V or 120 V pack, where the TO-251 body sits on a heatsink tab and the 0.50 C per watt case to sink figure is the number that decides the thermal stack.

It is a poor choice for a low voltage load switch, where 0.176 ohm is two orders of magnitude away from what a 12 V rail wants, and for a high frequency bridge, where the 250 ns diode and the 4.8 V per nanosecond limit both point at a snubbered, slower leg.

Sourcing notes and the second source question

A 250 V planar part with a repetitive avalanche rating is a substitution risk, because trench parts at the same resistance usually have no repetitive avalanche row at all. A buyer who swaps one for the other keeps the voltage and the resistance and loses the rating that was protecting the circuit. Our obsolete part cross reference hub lists the avalanche rows beside the electrical data for exactly this comparison, and it names the circuits where the row has to be re-measured rather than assumed.

Where the original is no longer available, the power management cross reference also carries the package and the thermal path, since a TO-251 and a DPAK share a footprint family but not a tab thickness, and the case to sink figure depends on the mounting pressure as much as on the part.

Questions we answer before a reel is booked

The first question is which junction temperature applies. The title says 175 C and the operating range says 150 C, so a build that needs the higher figure should ask the vendor for a written confirmation rather than assume the title. The second is the avalanche rating. A single pulse of 550 mJ is generous, the repetitive rating of 13 mJ is not, and a circuit that avalanches on every switching cycle is bounded by the smaller number.

The third question is the diode. At 1.8 V and 250 ns this part belongs in a leg with a dead time and a snubber, and a buyer who needs a fast diode should not buy a planar part and hope. The fourth is the source inductance: with 7.5 nH published, a gate loop that shares the source lead will lose drive at the switching edge, so a Kelvin connection or a separate source return is worth the copper cost.

On supply, the part is packed in tubes or on tape depending on the order code, the reflow peak is 300 C for 10 seconds at 1.6 mm from the case, and the mounting torque for the tab is 1.1 newton metres on an M3 screw. Incoming inspection samples the on resistance at 10 V, the threshold at 250 microamp, the breakdown at 250 microamp and the diode drop at 14 A, and the avalanche row is verified on a sample basis rather than per lot.