VBED1101N
Product Specifications
VBED1101N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBED1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBED1101N: a 100 V N channel at 8.4 milliohm in a leadless body
The VBED1101N is an N channel trench MOSFET in the SOT-669 outline, printed at 100 V from drain to source with plus or minus 20 V on the gate. On resistance is 0.0084 ohm typical at a 10 V gate with 20 A flowing, 0.0092 ohm at a 6 V gate with 15 A and 0.0117 ohm at a 4.5 V gate with 10 A. Continuous drain current is 75 A with the case at 25 C, 28.6 A on a 10 second pulse with the ambient at 25 C and 24.9 A with the ambient at 70 C, and the pulsed rating is 250 A for 100 microseconds.
The SOT-669 is a leadless package with the drain on a large exposed pad and the source on three of the leads, which is what lets a 100 V die reach 8.4 milliohm in a body smaller than an SO-8. The same construction sets the constraints: the thermal path is the bottom pad rather than the leads, the solder joint under that pad has no fillet to inspect, and the vendor note on the sheet says a solder fillet at the exposed copper tip cannot be guaranteed and is not required for the bottom side connection. A buyer who plans incoming inspection around a visual fillet check is planning the wrong test.
The ratings a buyer checks first
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 20 A | 0.0084 ohm typical |
| On resistance at 6 V and 4.5 V gate | 0.0092 and 0.0117 ohm typical |
| Continuous drain current, case at 25 C | 75 A against the package limit |
| Continuous drain current, 10 second pulse, ambient at 25 C and 70 C | 28.6 A and 24.9 A |
| Pulsed drain current, 100 microsecond | 250 A |
| Avalanche current and energy | 30 A, 45 mJ into 0.1 mH |
| Power dissipation | 62.5 W at 25 C case, 5 W at 25 C ambient |
| Junction to ambient, 10 second pulse | 20 C per watt typical, 25 maximum |
| Junction to case | 1.5 C per watt typical, 2.0 maximum |
| Gate threshold voltage | 1.4 V minimum, 2.6 V maximum |
| On state drain current at 5 V and 10 V gate | 30 A |
| Total gate charge at 10, 6 and 4.5 V gate | 35.5, 22 and 17.1 nC typical |
| Input, output and reverse transfer capacitance | 1855, 950 and 76 pF |
| Turn on delay and rise time at 10 V gate | 12 and 8 ns typical |
| Body diode forward voltage at 5 A | 0.76 V typical, 1.1 V maximum |
| Junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The 75 A row is a package limit and the 28.6 A row is the one that describes a board. At 28.6 A the die dissipates 6.9 W through 0.0084 ohm, and the 20 C per watt pulse path supports it from a 60 C ambient to a 150 C junction with a little margin. In the steady state the sheet gives a maximum of 70 C per watt, which brings the same junction to 150 C at 1.3 W, or 12 A. That is the honest continuous figure for a leadless body on a 1 inch pad, and it is the number a buyer should carry into a review rather than the 75 A headline.
The output capacitance is oddly large at 950 pF against 1855 pF of input capacitance, which tells you this is a wide die built for conduction rather than a switching part. The reverse transfer capacitance is only 76 pF, so the Miller plateau is short and the switching is clean, but 950 pF of output capacitance at 100 V stores 4.75 microjoule, which is 475 milliwatt at 100 kHz in a bridge leg before any load current is counted. On a synchronous rectifier or a load switch the figure does not matter; in a hard switched half bridge it is the first loss to calculate.
Gate charge is quoted at three drive levels and the spread is informative: 35.5 nC at 10 V, 22 nC at 6 V and 17.1 nC at 4.5 V, with 5.3 nC of gate source charge and 7.3 nC of gate drain charge. Half the charge at 10 V is the plateau region, which is why a 4.5 V drive both lowers the charge and slows the edge. The gate resistance is 0.5 ohm typical, 1.3 typical to maximum and 2.0 ohm maximum, so the external resistor sets the edge on any normal driver and the internal spread is a second order effect.
The body diode is the strongest row relative to the current class. Forward drop is 0.76 V at 5 A and 1.1 V maximum, recovery is 38 ns typical and 75 maximum with 36 nanocoulomb typical and 70 maximum of recovered charge, and the diode is rated to 75 A continuous at a 25 C case, the same as the channel. A synchronous rectifier can therefore rely on the diode during dead time without a separate rating argument, and the 0.76 V at 5 A is low enough that a light load does not lose efficiency to diode conduction.
Where a 100 V N channel at 8.4 milliohm earns its place
The first case is a synchronous rectifier on the secondary of a 48 V converter, where 100 V covers the ringing and 0.0084 ohm keeps the conduction loss small at 20 A. The second is a primary side switch in a 48 V to 12 V converter or a 60 V motor drive, where the 250 A pulse covers the startup and the 20 C per watt pulse path keeps a 25 A peak inside the junction limit. The third is a hot swap or OR-ing path on a 48 V rail, where the low output capacitance matters less than the resistance and the leadless body saves the board area that a DPAK would take.
It is a poor choice for a hard switched bridge at high frequency, where the 950 pF of output capacitance sets a loss that a 100 V part with a smaller die would avoid, and for a wave soldered board, where a leadless body with an exposed pad is not a through hole part and the vendor note explicitly discourages hand rework with an iron.
Sourcing notes and the second source question
A leadless body turns the second source question into a footprint question. Two SOT-669 parts can share a pad pattern and still differ in pad thickness and in the recommended stencil aperture, and the thermal performance depends on the voiding under the exposed pad rather than on the solder visible at the edge. Our power management cross reference carries the body and the thermal resistance beside the resistance, so the substitute is compared on the pad it will be soldered to.
Where a substitute has to be proven, how to verify a drop in replacement covers the checks that matter on a leadless part: voiding under the pad by x-ray, the on resistance at the hot corner, the diode recovery at the real load current and the case temperature on the customer's own copper. The diode row is the one most often left out and the one that decides whether a synchronous rectifier survives a short circuit.
Questions we answer before a reel is booked
The first question is whether 75 A can be used. It cannot; it is the package limit at a 25 C case, and the useful figures are 28.6 A on a 10 second pulse and about 12 A in the steady state on a 1 inch pad. The second is the gate drive. At 4.5 V the resistance is 0.0117 ohm, which is 40 per cent above the 10 V figure, so a 5 V rail driver should either use a charge pump or accept the higher loss.
The third question is about rework. The sheet states that manual soldering with an iron is not recommended for leadless components, so a board that expects field repair needs a hot air or a reflow station rather than a soldering iron. The fourth is the avalanche row: 45 mJ into 0.1 mH is modest, and a circuit that can commutate a cable inductance needs a clamp rather than reliance on the die.
On supply, the part travels on tape with the date code on the label, the reflow peak is 260 C, and the moisture level follows the packing list. Incoming inspection samples the on resistance at a 10 V gate, the threshold at 250 microamp, the breakdown at 250 microamp and the diode drop at 5 A, and it checks pad voiding by x-ray on the first article of each lot rather than on every board.