VBE2311
Product Specifications
VBE2311
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE2311 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE2311: a minus 30 V P channel at 11 milliohm in TO-252
The VBE2311 is a P channel MOSFET in the TO-252 outline, printed at minus 30 V from drain to source with plus or minus 20 V on the gate, and it is one of the few parts in this band that combines a single digit milliohm resistance with a 30 V rating. On resistance is 0.011 ohm typical at a minus 10 V gate with 30 A flowing, 0.015 ohm at a 125 C junction and 0.019 ohm at 175 C. Continuous drain current is minus 60 A with the case at 25 C against a package limit, minus 45 A with the case at 125 C, and the pulsed rating is minus 240 A.
P channel at 30 V with 11 milliohm is the profile of a high side battery switch, an input reverse polarity path or a load switch on a 12 V to 24 V rail, and the numbers line up with that: 60 A of package limited current, a threshold between minus 1 V and minus 3 V, and a gate that is comfortable at plus or minus 20 V. What the sheet does not say in one line is that the thermal data is printed for larger bodies than the drawing shows, which is the first thing a buyer has to reconcile.
The ratings a buyer checks first
| Drain to source voltage | minus 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, 30 A, 25 C | 0.011 ohm typical |
| On resistance at minus 10 V gate, 125 C and 175 C | 0.015 and 0.019 ohm |
| On resistance at minus 4.5 V gate, 20 A | 0.013 ohm typical |
| Continuous drain current, case at 25 C and 125 C | minus 60 A and minus 45 A |
| Pulsed drain current | minus 240 A |
| Avalanche current and energy | minus 50 A, 180 mJ into 0.1 mH |
| Power dissipation | 127 W at 25 C case, 3.75 W at 25 C ambient |
| Junction to case | 0.8 C per watt |
| Junction to ambient | 40 C per watt on a PCB mount, 62.5 C per watt in free air |
| Gate threshold voltage | minus 1 V minimum, minus 3 V maximum |
| On state drain current at 5 V and 10 V gate | minus 120 A |
| Total gate charge at minus 10 V gate and minus 15 V drain | 160 nC typical, 240 nC maximum |
| Input, output and reverse transfer capacitance | 3300, 1565 and 715 pF |
| Turn on delay and rise time | 25 and 225 ns typical |
| Body diode forward voltage at 75 A | minus 1.2 V typical, minus 1.5 V maximum |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The body is drawn as a TO-252, but the thermal table names a TO-263 and a TO-220AB, and the 127 W dissipation row carries a footnote that refers to those two bodies as well. That is not a rounding difference. A TO-252 tab soldered to 1 square inch of copper is nearer 40 C per watt junction to ambient, where the printed free air figure of 62.5 C per watt belongs to a TO-220AB standing on its leads. On a 60 A part the difference is the whole thermal budget, and a buyer should price the copper area before promising a current.
The whole thermal budget is the phrase that matters here, because at 60 A the die dissipates 40 W: 0.011 ohm at 60 A is 39.6 W, which is a third of the 127 W printed case figure and far beyond what a DPAK pad removes. The honest continuous current in still air sits between 15 A and 25 A depending on copper, which is still a lot for a 30 V P channel and is the reason the part exists. The 175 C junction rating is the other half of that argument: a part that runs at 130 C with margin is a cheaper answer than a bigger heatsink.
Gate charge is 160 nC typical and 240 nC maximum at a minus 10 V gate with minus 15 V on the drain, and 32 nC of that is gate source charge against 30 nC of gate drain charge. A driver that can source and sink half an amp will switch the part in the times the sheet prints, but a 20 milliamp microcontroller pin will not, and the 3.3 ohm internal gate resistance on some members of this family is small enough that the external resistor is what sets the edge. The threshold at minus 3 V maximum means a P channel driven from a 3.3 V rail has only 0.3 V of overdrive at the hot corner, so the minus 4.5 V column is the realistic drive for a battery product.
The body diode row is better than the current class suggests. Forward drop is minus 1.2 V typical at 75 A and minus 1.5 V maximum, reverse recovery is 55 ns typical and 100 maximum with only 0.07 microcoulomb typical of recovered charge, which is a fast diode for a P channel of this size. In a reverse polarity path where the body diode conducts before the channel is turned on, that low recovered charge is what keeps the input rail from ringing when the FET comes on.
Where a minus 30 V P channel at 11 milliohm earns its place
The first case is a battery disconnect on a 12 V to 24 V pack where the switch sits in the positive line and the gate has to be pulled below the source. The second is a reverse polarity protection path on a 24 V industrial input, where a P channel needs no charge pump and no isolated gate drive, and where the body diode drop during startup is the only penalty. The third is a load switch on a 5 V or 12 V rail where the 60 A pulsed rating covers a motor inrush and the 175 C junction covers a sealed enclosure without a derating argument.
It is a poor choice where the gate drive is a 3.3 V logic pin with no level shift, because the threshold reaches minus 3 V and the on resistance at minus 4.5 V is already 18 per cent higher than at minus 10 V. It is also a poor choice where the switch has to be in the ground return, since that path wants an N channel with a fraction of the resistance at the same price.
Sourcing notes and the second source question
A 30 V P channel at 11 milliohm is a part where the second source question is a threshold and gate rating question before it is a resistance question. A competitor with the same resistance but a minus 2.5 V threshold needs a gate drive that goes 2.5 V below the source at the cold corner, and a competitor with a minus 12 V gate rating will not survive a 24 V rail that rings. Our pin to pin cross reference carries the threshold window, the gate rating and the thermal resistance beside the resistance, which is the only way to compare two P channels honestly.
Where the part has to be proven on the customer's own board, how to verify a drop in replacement lists the tests that catch the usual failures: on resistance at the hot corner with the real gate drive, threshold at the cold corner, body diode conduction during startup and the tab temperature on the actual pad. A P channel that passes on the bench at 25 C and fails in a 70 C box usually fails on the threshold row rather than on the resistance row.
Questions we answer before a reel is booked
The first question is which thermal figure applies. The 127 W row belongs to a TO-263 or a TO-220AB, the drawing shows a TO-252, and a buyer needs the DPAK number for their own copper before a current is promised. The second is the drive voltage. At minus 4.5 V the resistance is 0.013 ohm, and at minus 10 V it is 0.011 ohm, so a 12 V rail with a resistor divider and a zener is the simplest way to get the lower figure without exceeding the 20 V gate rating.
The third question is about the diode. A P channel in a reverse polarity path conducts through its body diode until the gate is driven, and at minus 1.2 V and 75 A that is 90 W for the duration of the startup ramp, so the gate has to come on quickly or the diode has to be bypassed on the first milliseconds. The fourth is the leakage: minus 250 microamp at 175 C is small against a 60 A load and not small against a sleeping battery product, where the pack sits for months.
On supply, the TO-252 tape follows the standard outline, the reflow peak is 260 C, and the date code and moisture level travel on the label. Incoming inspection samples the on resistance at a minus 10 V gate, the threshold at 250 microamp, the breakdown at 250 microamp and the gate leakage at plus or minus 20 V, because the threshold and the leakage are the two rows that move first on a trench P channel.