Contact Us

VBE165R15S

Brand: VBsemi
VBsemi VBE165R15S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE165R15S — Discrete & Power Semiconductors | Superb Automation

VBE165R15S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE165R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE165R15S: a 650 V super junction switch in a TO-252 body

The VBE165R15S is an N channel super junction MOSFET in the TO-252 outline, printed at 650 V from drain to source with plus or minus 30 V on the gate. On resistance is 0.240 ohm typical at a 10 V gate with 5 A flowing, continuous drain current is 15 A with the case at 25 C and 9 A with the case at 100 C, and the pulsed rating is 45 A. The part is avalanche rated at 350 mJ from a 100 V rail into a 30 mH inductor, which is the row that matters on a mains derived supply where the leakage inductance of a transformer is not under the buyer's control.

Super junction means the drift region is doped with alternating p and n columns, so the blocking voltage and the on resistance are no longer traded against each other in the way a planar part forces. The visible result on this datasheet is a 650 V device with 0.240 ohm and 25 nC of gate charge, where an older planar part at the same voltage would carry 1 ohm or more. The cost is a fast body diode and a capacitance that is hard to control, which is why the reverse recovery rows and the effective output capacitance rows are quoted separately rather than folded into a single figure.

The ratings a buyer checks first

Drain to source voltage650 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 5 A, 25 C0.240 ohm typical
Continuous drain current, case at 25 C15 A
Continuous drain current, case at 100 C9 A
Pulsed drain current45 A
Single pulse avalanche energy350 mJ from 100 V into 30 mH, 7 A peak
Power dissipation, case at 25 C180 W, 1.7 W per C derating
Junction to case, junction to ambient0.85 and 62 C per watt
Gate threshold voltage2.0 V minimum, 4.0 V maximum
Total gate charge at 10 V gate and 480 V drain25 nC typical
Input, output and reverse transfer capacitance1900, 51 and 12 pF
Turn on delay and rise time12 and 14 ns typical
Turn off delay and fall time61 and 16 ns typical
Body diode forward voltage at 12 A1.2 V maximum
Reverse recovery time and charge45 ns and 6.4 microcoulomb typical
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The 15 A rating and the 0.240 ohm resistance do not coexist in a real board, and that is the first thing to settle. Fifteen amps through 0.240 ohm is 54 W, which the TO-252 can only carry with the tab held near 25 C by a heatsink or by a large copper area. In still air the junction to ambient figure is 62 C per watt, so a 60 C ambient and a 150 C junction allow about 1.4 W, which is 2.4 A of continuous current. Between those two numbers sits every real application: a 3 A to 6 A load on a board with a decent pad, a 15 A pulse that lasts a few milliseconds, and nothing in between that should be assumed without a thermal calculation.

The on resistance row is measured at 5 A, a third of the current rating, so the figure a buyer plans with has to be scaled. The same die at 125 C is roughly 1.7 times the 25 C value, which puts it near 0.41 ohm, and the junction temperature coefficient is printed as 1.08 V per C of drain breakdown rather than as a resistance multiplier, so the scaling has to come from the curve rather than from a table row. On a 650 V part this matters less than on a 30 V part, because the resistance is not usually the loss that decides the heatsink, but it decides whether a 4 A load runs at 100 C or at 130 C.

The switching rows are what the super junction process buys. Turn on delay is 12 ns typical and 24 ns maximum, rise time 14 and 23 ns, turn off delay 61 and 110 ns, fall time 16 ns, all with a 9.1 ohm gate resistor and a 480 V drain supply. Gate charge is 25 nC with 8 nC of gate source charge and 10 nC of gate drain charge, and the gate resistance is 0.7 ohm typical. That combination lets a 650 V switch run at 100 kHz with a driver of a few hundred milliamps, which is the reason the part exists: a 65 W flyback or a 200 W power factor stage can be built with a small gate drive and a small snubber instead of a large one.

The body diode is the row that separates a good super junction part from a bad one in a bridge. Forward drop is 1.2 V maximum at 12 A, reverse recovery is 45 ns typical and 90 ns maximum, and the recovered charge is 6.4 microcoulomb typical and 12.8 maximum, measured at 100 A per microsecond with a 25 V reverse bias. On a hard switched bridge those numbers set the loss in the opposite device, and a 12.8 microcoulomb worst case at 100 kHz is 1.3 W of extra loss in the diode itself before the other device is counted.

Where a 650 V super junction device earns its place

The first case is a power factor correction stage on a 380 V bus, where the 650 V rating covers the switching overshoot with margin and the 45 A pulse covers the inrush at start up. The second is a flyback or a forward converter on a rectified 230 V mains, where the avalanche rating of 350 mJ does real work: a transformer with 5 per cent leakage at 100 W stores enough energy in a badly clamped node to destroy a part that is not rated for it. The third is a bridge leg in a small inverter or a motor drive at 400 V, where the fast body diode and the 51 pF of output capacitance decide the dead time that has to be programmed.

What the part is not good for is a linear pass element or a load switch on a 48 V rail. At 650 V the resistance is 0.240 ohm and the die is small, so a 5 A continuous load in a sealed box is already at the thermal limit, and a lower voltage part at a tenth of the resistance does the same job with a fraction of the loss. Sizing this device by voltage alone is the usual mistake, and it shows up as a hot tab rather than as a failed part.

Sourcing notes and the second source question

The second source question for a 650 V super junction part is not a resistance question, it is a capacitance and diode question. Two parts can both print 0.240 ohm and 650 V and still behave differently in a bridge, because the output capacitance, the recovered charge and the avalanche rating set the losses that the resistance row does not show. Our power management cross reference keeps the capacitance and the diode rows beside the voltage and the resistance, so a comparison starts from the switching behaviour rather than from the headline.

Where the original device has gone short or long lead time, the pin to pin cross reference carries the package outline and the pin assignment in the same row as the electrical data, because a TO-252 from one vendor and a TO-252 from another can differ in tab thickness and in the creepage to the gate lead. On a 650 V node the creepage is a safety row, not a convenience row, and it is the first thing a qualification test catches.

Questions we answer before a reel is booked

The first question is whether the 15 A rating can be used continuously. It cannot, unless the tab is held near 25 C. At 15 A the die dissipates 54 W, and the junction to case figure of 0.85 C per watt alone gives a 46 C rise over the case, before the pad or the heatsink is counted. A practical continuous current on a 1 inch copper pad with 60 C air is between 2 A and 3 A, and a buyer who needs more should be looking at a lower voltage part or a larger body rather than at a bigger heatsink.

The second question is about the gate drive. The threshold window runs from 2.0 V to 4.0 V, so a 3.3 V logic signal is not a reliable drive at the cold corner and a 10 V rail is the intended condition. The third is about the diode: with 45 ns of recovery and 12.8 microcoulomb worst case, a hard switched bridge at 100 kHz should be checked for the extra loss rather than assumed to be fine.

On supply, the part is packed in tape and reel with the date code on the label, the reflow peak is 260 C for 10 seconds at 1.6 mm from the case, and the moisture level follows the reel marking. Incoming inspection samples the on resistance at a 10 V gate, the threshold at 250 microamp, the breakdown at 250 microamp and the gate leakage at 20 V, because on a super junction die the threshold and the breakdown are the two parameters that drift first between lots.