VBE1630
Product Specifications
VBE1630
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1630 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1630: a 60 V, 26 milliohm N channel with a 175 C junction
The VBE1630 is a single N channel MOSFET in the TO-252 body with the drain connected to the tab, printed at 60 V from drain to source with plus or minus 20 V on the gate and a 175 C junction rating. On resistance is 0.026 ohm at a 10 V gate with 15 A flowing and 0.029 ohm at a 4.5 V gate with 10 A, rising to 0.055 ohm at 125 C and 0.069 ohm at 175 C at the 10 V drive. Continuous current is 45 A with the case at 25 C and 40 A at 100 C, the pulsed rating is 100 A, the source current is 23 A, and the single pulse avalanche energy is 20 mJ into 0.1 mH. The vendor position is a general purpose 60 V switch, and the numbers describe a part for a 24 V or 36 V rail carrying 10 A to 15 A with margin for a transient.
Thermal resistance is 18 C per watt junction to ambient on a 10 second pulse, 40 C per watt in the steady state, and 3.2 C per watt junction to case, with 100 W of dissipation at a 25 C case and 3 W in still air. At 10 A the die loses 2.6 W at a 10 V gate, which is 8 C on the case path and 104 C on the steady state ambient path. That puts the part in the class where a 1 inch square pad is enough for 10 A in a 60 C enclosure and a heat spreader is needed above 15 A, and the 175 C junction gives the headroom to make that choice rather than lose the rail.
The ratings a buyer checks first
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 15 A | 0.026 ohm |
| On resistance at 4.5 V gate, 10 A | 0.029 ohm |
| On resistance at 125 C and 175 C junction | 0.055 ohm and 0.069 ohm |
| Continuous drain current | 45 A at 25 C case, 40 A at 100 C case |
| Pulsed drain current | 100 A |
| Continuous source current, diode | 23 A |
| Single pulse avalanche | 20 A into 0.1 mH, 20 mJ |
| Power dissipation | 100 W at 25 C case, 3 W at 25 C ambient |
| Junction to ambient | 18 C per watt on a 10 second pulse, 40 C per watt steady state, 50 maximum |
| Junction to case | 3.2 C per watt typical, 4 maximum |
| Gate threshold voltage | 1.0 V minimum, 2.0 V typical, 3.0 V maximum |
| Total gate charge at 10 V gate | 11 nC typical, 17 nC maximum |
| Gate source and gate drain charge | 3 nC and 3 nC |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The threshold is the most useful row on this sheet: 1.0 V minimum, 2.0 V typical and 3.0 V maximum at 250 microamp, which makes the part a genuine 4.5 V drive device rather than a 10 V device that pretends. A 4.5 V gate has 1.5 V of overdrive on a worst case die and the 0.029 ohm row is only 12 per cent above the 10 V figure, which is a small penalty compared with the parts in this band whose threshold runs to 4 V or 5 V. A 3.3 V drive has 0.3 V of overdrive and is not recommended, but a 5 V rail is comfortable.
Gate charge is 11 nC typical and 17 nC maximum at a 10 V drive, with 3 nC of gate source charge and 3 nC of gate drain charge, and capacitance of 1850 pF input, 140 pF output and 60 pF reverse transfer. Those are the numbers of a modest die: the driver moves 1.1 mA at 100 kHz and 3.3 mA at 300 kHz, the output capacitance loss at 30 V and 300 kHz is 38 mW, and the Miller ratio of thirty to one means the gate is quiet. The switching times are 8 ns turn on delay and 15 ns rise, 30 ns turn off delay and 25 ns fall at 23 A with a 2.5 ohm gate resistor, which is fast enough for 300 kHz and slow enough that the gate loop does not have to be perfect.
The diode is where this part is smaller than its siblings: 23 A continuous and 50 A pulsed, with 1.0 V typical and 1.5 V maximum forward drop at 15 A, and 30 ns to 60 ns of reverse recovery. A 23 A diode on a 45 A channel means the part is not a synchronous rectifier at the top of its current range, and a bridge that relies on the diode during a long dead time will heat it before it heats the channel. For a low side switch or a load switch the diode is only active during a fault, and 23 A is enough for that.
Where a 60 V, 26 milliohm switch with a 175 C junction earns its place
The first case is a 24 V or 36 V load switch or a battery disconnect carrying 10 A, where a 3.3 V or 5 V logic rail has to drive the gate and the 3.0 V maximum threshold makes that possible without a charge pump. At 10 A the die loses 2.6 W, which on a 1 inch pad and a 60 C enclosure puts the junction near 160 C at the steady state 40 C per watt, so the pad has to be larger than the package or the current has to come down. The second case is a low side switch in a small motor drive on a 36 V rail, where the 100 A pulsed rating covers the stall and the 20 mJ avalanche rating covers the coil kick.
The third case is a 48 V rail in a product that is battery backed and needs a 25 per cent margin on the blocking voltage; 60 V is generous there and the part is chosen for its threshold and its price rather than for its resistance. It is the wrong choice for a 48 V synchronous buck above 15 A, where a 5 milliohm part with a 10 V driver does the same job with less copper, and it is the wrong choice for a synchronous rectifier on a 12 V output at 20 A, where the 23 A diode becomes the limit during the dead time.
Sourcing notes and the second source question
This is the class of part where a replacement is usually required because the original body is small and old, and where the threshold window decides whether the substitute works at all. Our pin to pin cross reference keeps the threshold, the gate charge and the hot resistance in the same row as the 25 C resistance, so a customer can see at a glance whether a candidate needs a different gate drive. For a part whose original vendor has stopped the body, the obsolete part cross reference hub sets out how a replacement is chosen and what has to be re-qualified on the board.
The tests that catch a bad substitute on this kind of switch are the ones a bench can run in an afternoon: turn on at the cold corner, resistance at 125 C, gate ringing at the new charge and the diode behaviour in the dead time. A part that matches at 25 C and drifts at 125 C will pass an incoming inspection and fail in a warm enclosure, which is why the hot row is quoted on this page rather than left to a footnote.
Questions we answer before a reel is booked
The first question is whether 45 A is a real rating. It is a case temperature figure and the part is 40 A at 100 C case with the tab soldered to copper; in still air the 40 C per watt steady state path makes it a 10 A to 12 A device in a 60 C enclosure. The second question is whether a 3.3 V rail can drive the gate. It cannot be relied on, because the maximum threshold is 3.0 V, so a 5 V rail or a small charge pump is the practical floor.
The third question is about the diode. The 23 A continuous rating is well below the channel current and the forward drop at 15 A is 1.0 V, so a reverse current path has to be handled by the circuit rather than by the part. The fourth is about avalanche. The 20 mJ single pulse into 0.1 mH is the smallest in this band and reflects the smaller die, so a motor or a solenoid on this part needs a clamp across the coil.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and the drain is connected to the tab, so the tab is electrically live and the pad under it is part of the drain node. Incoming inspection samples the on resistance at 10 V and 4.5 V, the threshold at 250 microamp and the hot resistance at 125 C, which is the row that separates a good lot from a marginal one.