Contact Us

VBE1337

Brand: VBsemi
VBsemi VBE1337 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE1337 — Discrete & Power Semiconductors | Superb Automation

VBE1337

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE1337 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE1337: a 30 V, 37 milliohm N channel for secondary side work

The VBE1337 is a single N channel MOSFET in the TO-252 body, printed at 30 V from drain to source with plus or minus 20 V on the gate, halogen free to IEC 61249-2-21 and tested for gate resistance and unclamped inductive switching. On resistance is 0.037 ohm at a 10 V gate with 12 A flowing and 0.055 ohm at a 4.5 V gate with 10 A. Continuous current is 15 A with the case at 25 C and 15 A again at 70 C because the part is package limited before the die is, with a 100 A pulsed rating and 80 mJ of single pulse avalanche energy. The vendor names secondary synchronous rectification and DC to DC conversion, which is exactly where a 30 V part with this resistance belongs: a 12 V output, a 5 V output, or a low voltage rail on the secondary of an isolated converter.

The thermal data is more generous than the package suggests. Junction to case is 2.1 C per watt, junction to ambient is 46 C per watt on an FR4 pad, and the dissipation is 59.5 W with the case at 25 C against 2.7 W in still air. At 10 A the die loses 3.7 W at a 10 V gate and 5.5 W at 4.5 V, which is the difference between a part that works with a small heat spreader and one that needs a bigger one. The 15 A current rating is package limited at both case temperatures, so the bonding wire, not the silicon, is what a buyer is really rating.

The ratings a buyer checks first

Drain to source voltage30 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 12 A0.037 ohm
On resistance at 4.5 V gate, 10 A0.055 ohm
Continuous drain current15 A at 25 C case and at 70 C case, package limited
Pulsed drain current100 A
Continuous source to drain diode current50 A at 25 C case
Single pulse avalanche40 A into 0.1 mH, 80 mJ
Power dissipation59.5 W at 25 C case, 2.7 W at 25 C ambient
Junction to ambient, junction to case46 and 2.1 C per watt
Gate threshold voltage1.5 V minimum, 2.5 V maximum
Total gate charge at 10 V and at 4.5 V44 nC and 21.7 nC typical, 66 and 32.6 maximum
Gate source and gate drain charge7 nC and 6.7 nC
Input, output and reverse transfer capacitance2780, 641 and 260 pF
Gate resistance0.4 ohm typical, 2 ohm, 4 maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The threshold window of 1.5 V to 2.5 V is tight, and that is the useful part of this sheet. A 4.5 V drive has 2 V of overdrive on the worst case die, so the 0.055 ohm row is a real number and not a hopeful one, and a 3.3 V rail has 0.8 V of overdrive, which is enough to turn the part on but not enough to promise the resistance. The leakage rows show the same tight die: 1 microamp at 25 C, 50 microamp at 125 C and 250 microamp at 150 C, with plus or minus 250 nA of gate leakage, which is a small die and a dry one.

Gate charge is 44 nC at a 10 V drive and 21.7 nC at 4.5 V, with 7 nC of gate source charge and 6.7 nC of gate drain charge. At 300 kHz that is 13 mA of average gate current and 130 mW in the driver, which any small driver can supply. The switching rows are quick: 8 ns turn on delay and 9 ns rise, 35 ns turn off delay and 9 ns fall at 10 A with a 1 ohm gate resistor. The turn off delay of 35 ns is the longest row and it matters on a synchronous rectifier, because it is the time during which the body diode conducts before the channel takes over, and a controller that provides only 20 ns of dead time will keep the diode in play and pay the recovery charge every cycle.

The capacitance ratio is the other number to read: 641 pF of output capacitance and 260 pF of reverse transfer against 2780 pF of input capacitance, which is a Miller ratio near eleven to one. In a switching stage the output capacitance is what has to be charged and discharged each cycle, and at 30 V and 300 kHz, 641 pF is 0.58 microcoulomb per cycle and about 175 mW of loss before any current flows. That is the floor for this die at that frequency, and no gate resistor reduces it.

Where a 30 V, 37 milliohm switch earns its place

The first case is the synchronous rectifier on a 12 V output of an isolated converter, where the part sees 12 V plus ringing and 30 V is the usual rating for that node. At 8 A the die loses 2.4 W at a 10 V gate, which a TO-252 tab on a modest copper area handles with the case near 90 C. The second case is a buck converter from 24 V to 5 V at 5 A, where the 100 A pulsed rating covers the startup inrush and the 80 mJ avalanche rating covers the leakage of a small inductor. The third is a low voltage motor or solenoid low side switch on a 24 V rail, where the 15 A package limit is the honest operating point rather than the 100 A pulse.

The part is a poor choice on a 48 V rail, because 30 V leaves no margin for the leakage spike of a transformer or the back EMF of a motor, and it is a poor choice above 300 kHz because the output capacitance loss takes over. In those cases a 60 V or 100 V member of the family with a smaller die is the better trade, and the resistance difference is smaller than the switching loss it saves.

Sourcing notes and the second source question

Secondary side rectifiers are a part where two vendors print the same on resistance and different output capacitance, and the capacitance is what sets the loss at the frequency the converter actually runs. Our pin to pin cross reference carries the output capacitance, the threshold maximum and the gate charge beside the resistance, so a replacement is compared on the rows that decide the loss. When a customer needs a part against a schedule rather than a spec, the route in component lead time solutions covers the reels that can be booked from stock with a date code window.

For a part being introduced into an existing converter, the first three tests are always the same: switching loss at the real frequency, dead time against diode conduction, and junction temperature at the case the product reaches. The power management cross reference keeps the voltage class and the package together so a customer can see whether the alternative is a drop in or a board change, and where the answer is a board change we say so before a sample is ordered.

Questions we answer before a reel is booked

The first question is whether 15 A is a real rating. It is a package limit, and it applies at both case temperatures, which is unusual and worth noting: the die would carry more, but the bond wires will not. The second question is whether the 4.5 V row is usable on a 3.3 V rail. It is not; a 3.3 V drive sits 0.8 V above the maximum threshold and the resistance is undefined, so a 5 V driver is the floor for this part.

The third question is about the diode. The 50 A continuous diode rating is generous for a 15 A channel, so the freewheel current is not the constraint; the 641 pF output capacitance is. The fourth is about avalanche. The 80 mJ single pulse into 0.1 mH covers the leakage of a small inductor, and a converter that runs a larger leakage needs a clamp rather than a bigger rating.

On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and the diode forward voltage row is printed at a 10 A test condition, which is the current to use when comparing against a competitor sheet. Incoming inspection samples the on resistance at 10 V and 4.5 V and the threshold at 250 microamp.