Contact Us

VBC6N2014

Brand: VBsemi
VBsemi VBC6N2014 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBC6N2014 — Discrete & Power Semiconductors | Superb Automation

VBC6N2014

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBC6N2014 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBC6N2014: a dual 20 V N channel in a TSSOP-8

The VBC6N2014 is a dual N channel MOSFET in a TSSOP-8 outline, printed at 20 V from drain to source with plus or minus 12 V on the gate, available with halogen free terminations. Each half is 0.014 ohm at a 4.5 V gate with 6.5 A flowing and 0.018 ohm at a 2.5 V gate with 5.5 A, which is a low threshold part built to work from a single lithium cell or from a 3.3 V logic rail without a charge pump. Continuous current is 7.6 A on a 10 second pulse and 6.2 A in the steady state with the ambient at 25 C, falling to 6.5 A and 4.5 A at 70 C. The 30 A pulsed rating and the 20 V blocking voltage put it in the load switch, protection and battery path band rather than in a motor bridge.

The TSSOP-8 body is the reason to look at this part. It is a thin package with eight leads and a 0.65 mm pitch, which suits a board that has no room for two SO-8 outlines, and the thermal path is correspondingly weaker: junction to ambient is 72 C per watt on a 10 second pulse and 100 C per watt in the steady state, junction to foot is 55 C per watt, and the dissipation is 1.5 W with the ambient at 25 C. A buyer who compares this part with an SO-8 dual on resistance alone will be surprised by the temperature rise, and the honest limit for a sealed product is nearer 3 A per channel than 7 A.

The ratings a buyer checks first

Drain to source voltage, each channel20 V
Gate to source voltageplus or minus 12 V
On resistance at 4.5 V gate, 6.5 A0.014 ohm
On resistance at 2.5 V gate, 5.5 A0.018 ohm
Continuous drain current, 10 second pulse7.6 A at 25 C, 6.5 A at 70 C
Continuous drain current, steady state6.2 A at 25 C, 4.5 A at 70 C
Pulsed drain current30 A
Continuous source current, diode conduction1.5 A on a pulse, 1.0 A steady state
Power dissipation1.5 W at 25 C, 0.96 W at 70 C on a pulse
Junction to ambient72 C per watt on a pulse, 100 C per watt steady state, 83 and 120 maximum
Junction to foot, steady state55 C per watt typical, 70 maximum
Gate threshold voltage0.6 V minimum, 1.6 V maximum
Total gate charge at 4.5 V gate12 nC typical, 18 nC maximum
Gate source and gate drain charge2.2 nC and 3.6 nC
Body diode forward voltage at 1.5 A0.71 V typical, 1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The threshold window of 0.6 V to 1.6 V is the whole point of this die. It turns on hard enough at 2.5 V to reach 0.018 ohm, which is a real number and not a leakage figure, and that is what allows a single cell product to switch a load without a boost converter for the gate. The price is paid in leakage and in noise immunity: the gate is only rated plus or minus 12 V, the gate body leakage is plus or minus 200 nA at 4.5 V, and the zero gate drain current is 1 microamp at 25 C rising to 25 microamp at 70 C, which is high enough that a battery path which is supposed to be off should be checked at the top of its temperature range rather than at room.

The switching rows are slow on purpose and a reader should not treat that as a defect. Turn on delay is 245 ns typical and 365 ns maximum, rise time 330 ns and 495 ns, turn off delay 860 ns and 1300 ns, and fall time 510 ns and 765 ns, all measured with a 6 ohm gate resistor and a 4.5 V drive. That is a part that turns on in about a microsecond, which is deliberate for a load switch: the slow edge limits inrush into a capacitive load and keeps a small cell from seeing a short circuit. A board that needs a fast switch at this voltage should use a different die rather than reduce the gate resistor, because the 12 nC of gate charge is what sets the edge and the resistor only trims it.

Gate charge is 12 nC typical and 18 nC maximum at a 4.5 V drive, with 2.2 nC of gate source charge and 3.6 nC of gate drain charge, and the gate body leakage means the gate can be held on with a resistor rather than a driven rail. The body diode is the row that matters for a battery path: forward drop is 0.71 V typical at 1.5 A and 1.2 V maximum, and the continuous diode current is only 1.5 A on a pulse and 1.0 A steady state, which is well below the 6.2 A channel rating. A reverse current condition therefore heats the diode rather than the channel, and the 0.71 V at 1.5 A is 1.1 W, which is most of the 1.5 W package budget.

Where a 20 V dual N channel with a low threshold earns its place

The first case is a single cell or dual cell battery product where the load switch has to work from 2.5 V and the board has no room for a gate supply. Two channels in one TSSOP-8 let one half switch the load and the other switch the charger path, with the gates driven from the same 3.3 V logic rail, and the 30 A pulsed rating covers the inrush of a motor or a capacitive load for the few microseconds it lasts. At 2 A the 0.014 ohm die loses 56 mW per channel, which on a 100 C per watt steady state path is 6 C of rise, so the part is comfortable well below its current rating as long as the current is not continuous at the headline figure.

The second case is a USB port or an accessory rail on a 5 V bus, where the 20 V rating leaves generous margin for a transient and the slow turn on keeps the port from collapsing the host rail. The third case is a protection path in a wearable or a handheld instrument, where the thin package and the 0.65 mm pitch allow the part to sit on the same side of the board as the connector and the 25 microamp leakage at 70 C is still small against a 500 mAh cell. In all three the resistance is not the deciding row; the threshold and the thermal path are.

Sourcing notes and the second source question

A 20 V dual N channel in TSSOP-8 with a 1.6 V threshold maximum is a part where the second source question is really a threshold question. A competitor body with a 0.018 ohm resistance but a 2.5 V threshold maximum will not turn on from a 2.5 V rail at the cold end of the window, and the board will work on the bench and fail in the field. Our pin to pin cross reference carries the threshold window, the gate rating and the thermal resistance in the same row as the resistance, so the comparison starts from the conditions rather than from the number a distributor prints in bold.

For a part that has to be proven before a build, how to verify a drop in replacement covers the tests that catch the usual failures on a low threshold load switch: turn on at the cold corner, leakage at the hot corner, inrush into the load capacitance and the temperature rise on the actual pad. Where a product is moving to a smaller package, the power management cross reference keeps the package and the thermal path beside the electrical rows, since a TSSOP-8 at 100 C per watt and an SO-8 at 85 C per watt do not carry the same current even when they share a resistance.

Questions we answer before a reel is booked

The first question is whether 6.2 A can be carried continuously. It can with the board at 25 C and a copper pad larger than the package, and it cannot in a sealed enclosure: at 6 A the die loses 0.5 W, which on 100 C per watt is a 50 C rise, and a 60 C box puts the junction at 110 C with the current still rising. The second question is whether the part can be driven from a 1.8 V rail. It cannot; the threshold maximum is 1.6 V, so a 1.8 V drive has 0.2 V of overdrive and no defined resistance, and the 2.5 V row is the lowest usable point in the sheet.

The third question is about the gate rating. Plus or minus 12 V is generous for a 20 V part but not for a 12 V rail that rings, so a gate resistor and a small clamp are the usual answer on an automotive style supply. The fourth is about the diode. The continuous diode current of 1.5 A is well below the channel rating, so a path that can be back fed has to be protected by the circuit rather than by the part.

On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and the TSSOP-8 tape orientation follows the standard outline. Incoming inspection samples the on resistance at 4.5 V and 2.5 V, the threshold at 250 microamp and the leakage at 70 C, because on a low threshold die the leakage is the parameter that drifts first between lots.