Contact Us

VBA5311

Brand: VBsemi
VBsemi VBA5311 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA5311 — Discrete & Power Semiconductors | Superb Automation

VBA5311

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA5311 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA5311: an N channel and a P channel at 30 V in one SO-8

The VBA5311 puts a 30 V N channel and a 30 V P channel in one SO-8 outline, halogen free to IEC 61249-2-21, with both gates rated plus or minus 20 V. The N channel is 0.011 ohm at a 10 V gate with 6.8 A flowing, 0.012 ohm at 8 V with 6.7 A and 0.013 ohm at 4.5 V with 6.6 A. The P channel is 0.021 ohm at minus 10 V with 8 A, 0.024 ohm at minus 8 V with 6.5 A and 0.028 ohm at minus 4.5 V with 5 A. The vendor files the part under motor drive, which is the application where one body holding both polarities pays: a half bridge built from a complementary pair needs one placement, one thermal path and one reel instead of two.

The two halves are not symmetrical and a buyer should treat them as two parts. The P channel is roughly double the resistance of the N channel at the same gate voltage, because a P channel of the same die area needs about twice the area for the same resistance, and its gate charge at a 4.5 V drive is 21.7 nC against 6.5 nC on the N channel. A low side switch built on the N half therefore runs cool and switches fast, and a high side switch built on the P half carries more loss and needs a driver that can sink the larger charge. That asymmetry is normal, and it is the first thing to check when a competitor part is quoted with a single resistance figure for both halves.

The ratings a buyer checks first

Drain to source voltage, both channels30 V N, minus 30 V P
Gate to source voltageplus or minus 20 V, both channels
On resistance, N channel0.011 ohm at 10 V, 0.012 at 8 V, 0.013 at 4.5 V
On resistance, P channel0.021 ohm at minus 10 V, 0.024 at minus 8 V, 0.028 at minus 4.5 V
Continuous drain current, summary row13.3 A N, 13 A P
Pulsed drain current, 10 microsecond60 A N, minus 60 A P
Source to drain diode current5.6 A N, minus 5.6 A P at 25 C case
Single pulse avalanche20 A both channels into 0.1 mH, 5 mJ N and 20 mJ P
Power dissipation6.1 W N, 5.2 W P at 25 C case
Junction to ambient on a 10 second pulse20 C per watt N, 27 C per watt P, 32.5 maximum both
Junction to foot, steady state10 C per watt N, 19 C per watt P typical
Gate threshold voltage1 to 2.2 V N, minus 0.9 to minus 2.5 V P
Total gate charge at 10 V and at 4.5 V13.3 nC and 6.5 nC N, 13 nC and 21.7 nC P
Input, output and reverse transfer capacitance1421, 755 and 254 pF N, 1515, 800 and 25 pF P
Body diode forward voltage0.81 V N at 5.4 A, minus 0.77 V P at 2 A
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The threshold windows are the first fork. The N channel is specified from 1 V to 2.2 V, so a 4.5 V gate has 2.3 V of overdrive on a worst case die and the 0.013 ohm row is usable. The P channel is specified from minus 0.9 V to minus 2.5 V, so a 4.5 V drive has 2 V of overdrive and the resistance is 33 per cent above the 10 V row. A product with only a 5 V rail can drive the N half directly and needs a small pull down device for the P half, and that device has to hold the gate 2.5 V below the source rather than simply tying it to ground.

The gate charge rows deserve a careful read, because the P channel numbers run the other way round from what a reader expects: the sheet prints 13 nC at a 10 V drive and 21.7 nC at 4.5 V. A charge that rises as the drive falls is not physically impossible but it is unusual, and the honest reading is to take the maximum column, 33 nC, as the driver budget for the P gate and let the lower figure be a typical at best. The N channel behaves normally, 13.3 nC at 10 V against 6.5 nC at 4.5 V. For a 200 kHz half bridge that is 6.6 mW on the N gate and 6.6 mW on the P gate at a 10 V rail, small enough that the driver dissipation is set by the gate resistor rather than by the charge.

The switching rows show the same asymmetry in time: at a 10 V drive the N channel turns on in 5 ns and off in 16 ns, while the P channel needs 10 ns to turn on and 50 ns to turn off, with 90 ns in the maximum column. At 4.5 V the P channel turn off delay stretches to 40 ns. That is slow enough that a half bridge running at high frequency will spend real time in the linear region on the P side, and the gate resistor has to be chosen for the P channel rather than copied from the N channel. The body diode figures follow: 17 ns recovery and 10 nC of recovered charge on the N channel, against 41 ns and 32 nC on the P channel, which is the number that decides whether a synchronous rectifier on the P side needs a parallel Schottky.

Where a complementary pair in one body pays

Motor drive is the application the vendor names, and a 24 V brushed motor driver is the textbook case: the N channel sits on the low side with a 10 V gate drive and the P channel on the high side with the gate pulled down from the rail, so no bootstrap capacitor is needed and the high side can be held on indefinitely for a locked rotor test. At 4 A the N half loses 0.21 W and the P half 0.45 W, which on a 20 C per watt and 27 C per watt path puts each junction about 5 C and 12 C above the board. That is comfortable in a 60 C enclosure and it is the reason a small driver with no heat sink is enough.

A second case is a 24 V or 28 V load switch with a reverse polarity block, where the P channel interrupts the positive lead and the N channel pulls its gate down. Here the P channel carries the load current continuously, and 5 A at 0.028 ohm on a 4.5 V drive is 0.7 W, which needs the drain pads stitched to a copper pour rather than a thin trace. A third case is a class D amplifier or a pulse width modulated heater where the two halves are used as a complementary output stage at a few hundred kilohertz; there the P channel charge and its slow turn off are the limiting rows, not the resistance.

Sourcing notes and the second source question

Complementary pairs are quoted in two ways on distributor pages, one resistance for the pair or one per channel, and the difference matters because a part sold as 0.015 ohm may be 0.015 on the N side and 0.030 on the P side. Our power management cross reference keeps the two polarities in separate rows with their own threshold window, gate charge and thermal path, so the comparison does not smooth over the asymmetry. When a customer sends a competitor code, the four rows we compare first are the resistance at the gate voltage actually in use, the threshold maximum, the total gate charge at that drive and the diode recovery charge.

For a replacement that has to be proven on the customer board, how to verify a drop in replacement lists the tests that find the usual problems on a half bridge: the shoot through window at the new gate resistance, the dead time the driver still needs, the recovery spike on the low side diode and the junction temperature of the smaller of the two dies. The pin to pin cross reference carries the bodies that share this outline, because a complementary pair that moves from SO-8 to a DFN changes the thermal path even when the pinout looks the same on paper.

Questions we answer before a reel is booked

The first question is whether one part can carry a 13 A motor. Not continuously. The 13.3 A figure is a summary row, the case temperature rows are the ones that apply, and the honest limit for a sealed driver is set by the 20 C per watt ambient path on the N side and 27 C per watt on the P side. At 6 A the N half dissipates 0.47 W and the P half 1.0 W, which is 9 C and 27 C of rise; at 10 A the P half is at 2.8 W and 76 C of rise, which is why the high side is the one that gets hot.

The second question is about the gate drive on the P side. A 4.5 V rail cannot pull the gate 4.5 V below a 24 V source through a resistor without a level shift, so the usual answer is a small N channel or a bipolar pull down that is rated for the full rail. The third is about avalanche. The P channel is rated for 20 mJ into 0.1 mH and the N channel for 5 mJ in this sheet, and a motor lead that is switched without a clamp will find the smaller number first.

On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, and incoming inspection samples the resistance of both channels at the two gate voltages plus the threshold at 250 microamp. This family publishes no orderable addendum, so no reel size or marking code is quoted here, and a customer who needs a specific date code window has to book it before the order is placed rather than hope for it on a mixed shipment.