VBA3638
Product Specifications
VBA3638
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA3638 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA3638: two 60 V N channels in a single SO-8 body
The VBA3638 is a dual N channel MOSFET in the SO-8 outline, printed at 60 V drain to source and plus or minus 20 V on the gate. Each leg carries 28 milliohm at a 10 V gate and 30 milliohm at 4.5 V, with 7 A at a 25 C case and 4 A once the case reaches 125 C. The two legs sit on separate drain pads, so they can be used as two independent switches or as one high side and one low side of a small synchronous converter. Bought as a pair in one body, the part saves board area and one reel position on a bill of materials that already carries a dozen line items.
The sheet names a 175 C junction limit, a 16.2 mJ single pulse avalanche rating into 0.1 mH, and a 110 C per watt junction to ambient figure on a one inch square board. Those three numbers decide most of the practical use. The 7 A headline belongs to a 25 C case with the drain pad soldered to a large copper area, and the same die in still air is a fraction of that. Builders who read only the front page and put the part on a narrow trace come back with a hot board and a short life.
The ratings a buyer checks first
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 28 milliohm typical, 4.5 A, 25 C |
| On resistance at 4.5 V gate | 30 milliohm typical, 4 A |
| Continuous drain current | 7 A at 25 C case, 4 A at 125 C case |
| Pulsed drain current, 300 microsecond | 28 A |
| Single pulse avalanche energy | 16.2 mJ into 0.1 mH |
| Power dissipation | 4 W at 25 C case, 1.3 W at 125 C case |
| Junction to ambient, one inch board | 110 C per watt |
| Junction to foot, drain pad | 34 C per watt |
| Operating junction range | minus 55 C to plus 175 C |
| Total gate charge | 11.7 nC typical, 18 nC maximum |
| Input capacitance | 600 pF typical, 750 pF maximum |
| Body diode forward voltage | 0.75 V typical at 2 A, 1.1 V maximum |
What the electrical table adds to the summary
The resistance rows carry three temperatures and they move a long way. At a 4.5 A test current the part reads 28 milliohm at 25 C, 66 milliohm at 125 C and 81 milliohm at 175 C. That is 2.4 times and 2.9 times the cold figure, so a conduction loss budget written from the front page is optimistic by a factor of two or more in a warm enclosure. The same applies to leakage: one microamp at 25 C, 50 microamp at 125 C and 150 microamp at 175 C, which matters in a battery path that has to sit idle for months.
The threshold window is 1.5 V minimum, 2.0 V typical and 2.5 V maximum at 250 microamp. A 4.5 V gate drive turns the part on hard with good margin, a 3.3 V drive works but sits closer to the knee, and a 2.5 V logic rail does not switch it with any certainty, especially cold. Gate charge is 11.7 nC typical and 18 nC maximum, so a small driver in a SOT-23 package is enough and the switching loss at 300 kHz stays modest. Turn on delay is 7 ns typical and rise 3.3 ns, turn off delay 22.4 ns and fall 2.1 ns, measured at 30 V with a 6.8 ohm load, which puts the part easily above a megahertz if the driver can keep up.
The gate resistance is quoted as a 1.3 to 6 ohm window rather than a typical, which is wide. Two reels of this code can therefore behave differently in a fast switching node, and the slower one rings less but switches later. Where the edge has to be matched across a batch, the gate resistor is the place to absorb that spread rather than the driver. The diode forward voltage of 0.75 V typical at 2 A and 1.1 V maximum also matters in a synchronous stage, because the dead time body diode conduction is a real loss at these currents.
Where the two legs earn their space
The most common use is a pair of switches in a 12 V or 24 V synchronous buck, one leg per rail, or one leg as the low side of a converter and the other as a load switch on the same board. Telecom line cards use the dual body for a 48 V input disconnect, with one leg in the return path so the card can be pulled without arcing the connector. Small motor drives use one leg per direction in an H bridge on a handheld tool, where the SO-8 keeps the loop short and the gate charge low enough for a battery powered driver.
PoE powered devices are a natural fit: the two legs can be arranged as a pass element and a disconnect, and the 60 V rating covers the 57 V maximum of a type 4 port with margin for the inductive kick when the cable is unplugged. LED strips and small backlight converters use the pair as two channels of a boost, and the 16.2 mJ avalanche rating gives some protection when a long cable is switched off without a clamp. In each case the 60 V ceiling, not the current, is what sets the limit.
Sourcing notes and the second source question
The SO-8 dual N channel pinout is close to a de facto standard across several vendors, but close is not the same as equal. Drain pad routing, gate resistance and threshold windows differ, and a part that drops in physically can still fail a conducted emissions limit or a cold start test. Our pin to pin cross reference starts from the pad geometry and the gate charge, not from the headline voltage and current. When a customer sends a competitor code, the four rows we compare first are on resistance at 4.5 V, threshold maximum, total gate charge and avalanche energy.
For a replacement that has to be proven on the customer board rather than on paper, the checklist in how to verify a drop in replacement covers the tests that catch the failures we see most: gate ringing at the new gate resistance, reverse recovery in the low side body diode, and thermal margin at the case temperature the product actually reaches. We supply this code along with the matching driver and gate resistor from the same bill of materials, and we kit the two legs as one reel position where the quantity allows.
Questions we answer before a reel is booked
Buyers ask whether the 7 A figure can be used at 25 C ambient. It cannot. It is a case temperature rating, and with 110 C per watt junction to ambient on a one inch board, the same part in still air carries roughly 1.3 A before the junction reaches 150 C. The second question is whether both legs can run at full current at once. They can electrically, but the package dissipation is 4 W total at 25 C case, so the two loads share one thermal budget and the answer depends on the duty cycle of each leg.
We are also asked about the diode conduction rating of 3.6 A, which is lower than the 7 A channel rating because the body diode is a narrower path and the package limits it. A synchronous stage that relies on the diode during a long dead time should be checked against 3.6 A, not against 7 A. On avalanche, the 16.2 mJ figure is a single pulse into 0.1 mH with the junction starting at 25 C; repeated events derate with temperature and with the repetition rate, so a clamp is still cheaper than a warranty claim.
Availability is quoted per reel with the date code stated on the label, and we hold the incoming inspection record for each lot, including the on resistance sample at 4.5 V. If a customer needs a specific date code window for a build that is already qualified, that has to be booked before the order is placed, because mixed date codes in one shipment are the usual reason a line stops for a re qualification it did not plan.