Contact Us

VBA3211

Brand: VBsemi
VBsemi VBA3211 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3211 — Discrete & Power Semiconductors | Superb Automation

VBA3211

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3211 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3211: two 20 V N channels in one SO-8 for low voltage rails

The VBA3211 is a dual N channel MOSFET in the SO-8 body, printed at 20 V drain to source and plus or minus 12 V on the gate. Each leg is 9 milliohm at a 4.5 V gate with 5 A flowing and 12 milliohm at 2.5 V with 4 A flowing, with 15 nC of typical gate charge at the 4.5 V point. Continuous drain current is 10 A with the case at 25 C, 7.0 A at a 70 C case, 8.1 A at a 25 C ambient and 7.2 A at a 70 C ambient, and the pulsed rating is 44 A. The vendor lists set top box and low current DC to DC conversion, which describes the job exactly: two small switches on a 5 V or 12 V rail that have to be cheap, quiet and small.

The two legs are separate dies in one body with their own gate and source pins and their own drain pads, so they can be wired as a half bridge, as two independent load switches, or as a redundant pair on one rail. Sharing one package means one reel position and one placement instead of two, which matters on a board that carries several hundred line items. It also means the two junctions share one thermal path through the lead frame, so the dissipation of both legs adds before it reaches the board, and a build that runs both legs at 4 A has to be checked against the combined figure rather than against the single leg rating.

The ratings a buyer checks first

Drain to source voltage20 V
Gate to source voltageplus or minus 12 V
On resistance at 4.5 V gate, 5 A9 milliohm
On resistance at 2.5 V gate, 4 A12 milliohm
Continuous drain current10 A at 25 C case, 7.0 A at 70 C case
Continuous drain current in still air8.1 A at 25 C ambient, 7.2 A at 70 C ambient
Pulsed drain current44 A
Continuous source to drain diode current3.25 A at 25 C case, 1.88 A in still air
Single pulse avalanche energy1.45 mJ, avalanche current 6 A into 0.1 mH
Power dissipation2.7 W at 25 C case, 1.78 W at 25 C ambient
Junction to ambient, junction to foot58 and 38 C per watt typical, 70 and 45 maximum
Gate threshold voltage0.5 V minimum, 1.0 V maximum
Total gate charge at 4.5 V3.7 nC typical, 5.6 nC maximum
Input, output and reverse transfer capacitance586, 117 and 55 pF
Body diode forward voltage at 2 A0.8 V typical, 1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

A low threshold part needs a careful gate

The threshold window is 0.5 V minimum to 1.0 V maximum at 250 microamp, which is a logic level part by any measure and also a part that turns on when the gate is left floating. With 3.7 nC of gate charge and 586 pF of input capacitance, a stray 1 V of coupled noise on an open gate is enough to put the leg into conduction, so a 100 k pull down on every gate is mandatory rather than optional, and the pull down has to be on the gate side of the series resistor so the resistor cannot isolate it. The same low threshold is what allows a 2.5 V drive to reach 12 milliohm, which is useful on a 3.3 V or 1.8 V rail where the gate is driven directly by a controller pin.

The gate rating is plus or minus 12 V, lower than the 20 V of the higher voltage parts in this family, so a 12 V rail used directly as a gate drive sits exactly at the limit and any ringing over it is a stress. On a 12 V system the gate has to be driven through a divider or from a dedicated driver on a 5 V rail. Turn on delay is 12 ns and rise 55 ns at a 4.5 V drive, which is slow for the edge and is a deliberate characteristic of a small die with a 4.3 ohm typical gate resistance; at a 10 V drive the rise drops to 9 ns. That difference tells a buyer which drive the part was characterised for, and it is the 10 V one for anything that switches.

Thermal data is the constraint on this part rather than the current rating. Junction to ambient is 58 C per watt on a 10 second pulse and up to 70 C per watt maximum, so at 4 A per leg with 9 milliohm each leg loses 0.14 W and the pair loses 0.29 W, which is 17 C above ambient and comfortable. At 8 A per leg the loss is 1.15 W and the junction climbs 67 C, which in a 60 C box is 127 C and leaves margin but no room for a hot day. The 2.7 W at a 25 C case is the figure for a board with a copper pour under the package, and the SO-8 at this size needs the drain tabs tied to that pour rather than to a thin trace.

Two legs, two jobs

In a set top box or a small router, one leg switches the 5 V rail into a subsystem and the other switches the 12 V rail into a fan or a hard disk. Neither carries a large current, both have to be quiet, and the 586 pF input capacitance with a 55 pF reverse transfer capacitance makes them easy to drive from a controller with a 100 ohm series resistor. The 44 A pulsed current covers the inrush into the decoupling bank on each rail, and the 1.45 mJ avalanche rating is small enough that a switched inductive load needs an external clamp, which on a 5 V rail is a single Schottky. Using the pair as a half bridge for a small synchronous converter at 500 kHz is the more demanding role, and there the 3.7 nC gate charge is the reason the part can be driven from a small integrated driver without a heat problem.

Battery powered equipment uses one leg as a reverse polarity switch and the other as a load disconnect, with both gates held low by the controller in standby. The zero gate voltage drain current is 1 microamp at 25 C and 10 microamp at 55 C per leg, so a 5 V rail that sits idle for a month loses almost nothing, and the 0.5 V minimum threshold means the part also works as a crude level shifter when the controller is on a 1.8 V rail. That last trick is common in portable products and is worth checking on the bench, because the same low threshold that makes it work also makes the part sensitive to a gate trace that runs beside a switching node.

Sourcing notes and the second source question

Dual N channel 20 V in SO-8 is one of the most copied bodies in the industry, and the pin maps are close but the internals are not. A candidate with the same 9 milliohm at 4.5 V can have twice the gate charge or a 0.3 V lower threshold, and either of those changes the driver and the pull down network. Our pin to pin cross reference compares the two legs separately, because a part can match on leg one and not on leg two, and the BOM consolidation view shows where one dual part can replace two singles and where the shared thermal path makes that a bad idea.

For a prototype build the kitting service is the practical route: a small quantity of this dual, a matching driver and the passives on the same lists, cut from the same date code, so a first article run does not stall on one line item. We hold the incoming record for on resistance at both gate voltages and for threshold at 250 microamp on every lot, and the tape orientation follows the SO-8 outline, so the feeder does not need a change.

Questions we answer before a reel is booked

Buyers ask whether both legs can carry 8 A at once. They can electrically, but the two junctions share one lead frame, so the combined loss of 1.15 W at 9 milliohm raises the whole package 67 C above ambient on the 58 C per watt path, and the second leg sees the first leg heat. The honest answer is 5 A per leg in a 60 C enclosure with a copper pour, and 8 A only if one leg runs in bursts. The second question is whether the 12 V gate rating is a hard limit. It is, and a 12 V rail used directly as the drive has no margin for ringing, so a 10 V clamp or a divider is the answer.

The body diode question comes up on every synchronous use. At 2 A the drop is 0.8 V typical, so a dead time of 100 ns at 500 kHz with 2 A costs about 40 milliwatt per leg, which is small but is not zero and has to be counted when the efficiency target is tight. For a load switch the diode never conducts and the row can be ignored. Avalanche is limited to 1.45 mJ into 0.1 mH, which means a solenoid or a relay coil on the same rail needs a clamp diode, and the 6 A avalanche current is not a switching rating.

On supply we quote the reel and the date code on the label, hold the gate charge and threshold records per lot, and can supply both legs from one date code so a parallel or bridge pair is matched. For a product that needs a specific threshold window, we can screen at 250 microamp against a limit the customer sets, which is the usual request from a product team that has no room in the gate network for a wide window.