Contact Us

VBA2410

Brand: VBsemi
VBsemi VBA2410 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA2410 — Discrete & Power Semiconductors | Superb Automation

VBA2410

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA2410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA2410: a minus 40 V P channel with 10 milliohm and 16 A

The VBA2410 is a single P channel MOSFET in the SO-8 body, printed at minus 40 V drain to source and plus or minus 20 V on the gate, with 100 per cent gate resistance and unclamped inductive switching testing on every unit. On resistance is 0.010 ohm at a minus 10 V gate with 10.2 A flowing and 0.014 ohm at minus 4.5 V with 8.4 A flowing. Continuous drain current is 16.1 A with the case at 25 C, 12.9 A at a 70 C case, 10.2 A at a 25 C ambient and 8.2 A at a 70 C ambient, and the pulsed rating is 50 A. The vendor files it under load switch and point of load conversion, which is where a 40 V P channel with this resistance earns its keep: a 24 V rail, a 28 V battery bus, or a 36 V industrial supply.

This is a large die for a P channel in SO-8. Input capacitance is 3007 pF, reverse transfer capacitance 291 pF and total gate charge 64 nC at a 10 V drive, or 33 nC at 4.5 V. Those are the numbers that decide the driver: a 64 nC gate charge switched at 100 kHz needs 0.64 mA of average drive current at 10 V, which any small driver supplies, but a resistor driven gate would turn on slowly and dissipate in the channel during the transition. The avalanche rating is 39 mJ with a 28 A pulse into 0.1 mH, which is enough for a modest inductive load without an external clamp.

The ratings a buyer checks first

Drain to source voltageminus 40 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate, 10.2 A0.010 ohm
On resistance at minus 4.5 V gate, 8.4 A0.014 ohm
Continuous drain current16.1 A at 25 C case, 12.9 A at 70 C case
Continuous drain current in still air10.2 A at 25 C ambient, 8.2 A at 70 C ambient
Pulsed drain current50 A
Continuous source to drain diode current5.3 A at 25 C case
Single pulse avalanche energy39 mJ, avalanche current 28 A into 0.1 mH
Power dissipation6.3 W at 25 C case, 2.5 W at 25 C ambient
Junction to ambient, junction to foot37 and 16 C per watt typical, 50 and 20 maximum
Gate threshold voltageminus 1.2 V minimum, minus 2.5 V maximum
Total gate charge at minus 10 V and minus 4.5 V64 nC and 33 nC typical
Input, output and reverse transfer capacitance3007, 335 and 291 pF
Body diode forward voltage at 8.2 Aminus 0.8 V typical, minus 1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the switching rows against the drive point

The document gives two switching sets, one at a minus 10 V gate and one at minus 4.5 V, and the difference is the story of this part. At 10 V the turn on delay is 13 ns, rise 11 ns, turn off delay 45 ns and fall 9 ns. At 4.5 V the same part shows 57 ns, 50 ns, 40 ns and 17 ns. A slow turn on at a low drive voltage is a controlled inrush, which is useful in a hot swap role, and a liability in a converter that switches every cycle, because the die spends 50 ns in the linear region each edge. At 100 kHz with 10 A that is roughly 0.1 W of extra loss per edge pair, small but not free, and at 300 kHz it becomes the reason to raise the gate drive.

The threshold window is minus 1.2 V to minus 2.5 V at 250 microamp. On a 4.5 V drive the worst case die has 2 V of overdrive, which is adequate, and on a 3.3 V drive it has 0.8 V, which is not enough for the 10 milliohm figure. The gate resistance row is 0.4 ohm minimum, 2 ohm typical and 4 ohm maximum, so the internal gate node is not a heavy load and a 4.7 ohm external resistor gives a smooth edge without slowing the part into a loss. The reverse transfer capacitance of 291 pF is high for a die of this size and is the reason the Miller plateau is visible on a scope at a 24 V drain: a small gate driver with 1 A of peak current keeps the plateau short, and a 100 k resistor pull down does not.

Thermal data decides the current that can be documented rather than the current that can be measured once. Junction to foot is 16 C per watt typical, so at 10 A with 10 milliohm the die loses 1 W and the junction sits 16 C above the foot temperature, which is the case to build for when the tab is soldered to a copper pour. Junction to ambient is 37 C per watt on a 10 second pulse, so the same 1 W in still air puts the junction 37 C above ambient, and at 60 C ambient that is a 97 C junction with margin, while at 85 C ambient it is 122 C and the current has to come down. The 6.3 W at a 25 C case is a heat spreader figure and is meaningless for a part on a two layer board.

Where 40 V and 10 milliohm make the difference

A 24 V industrial rail with a 30 V transient is the natural home. A 30 V part needs a clamp for that transient, a 40 V part does not, and the 10 milliohm die keeps the conduction loss at 0.9 W for a 9 A load. Point of load converters that run from 24 V down to 5 V use the P channel as the high side switch with no charge pump, and the 11 ns rise at a 10 V drive keeps the switching loss low enough that a 500 kHz converter stays under 2 W total. Load switching on a 28 V battery bus is the other case: the 39 mJ avalanche rating absorbs the kick from a contactor coil, and the 50 A pulsed current covers the inrush into a bank of electrolytic capacitors.

Portable equipment with a 36 V tool pack uses the part as a reverse polarity and disconnect switch, where the 0.010 ohm at 10 A gives a 100 mV drop and the 3007 pF input capacitance means the turn on has to be shaped by the gate network rather than by the driver, because a fast edge into a capacitive load rings the pack leads. Two parts in parallel are a common request for a 20 A load, and at this resistance the pair gives 5 milliohm, but the threshold window of 1.3 V across the population means the two do not share perfectly in the linear region, so the resistors in each gate have to be matched to force the sharing during the inrush.

Sourcing notes and the second source question

A minus 40 V P channel at 10 milliohm in SO-8 is near the practical limit of the body, because the die has to be large to reach that resistance at a 40 V rating. That makes second sourcing harder than the headline suggests: the candidates that match the resistance often have a different gate charge, and the candidates that match the gate charge are 14 to 20 milliohm. Our power management cross reference keeps the gate charge and the thermal resistance in the same row as the resistance, and the cost comparison in how to reduce component cost shows where a 14 milliohm part is the cheaper answer because the driver, the pad and the copper all get smaller.

Date code discipline matters more on a part like this than on a logic device, because a change of die in the same body shows up as a shift in gate charge and threshold that a driver setting tuned to the old lot will not tolerate. The controls in date code management cover the reservation, the labelling and the traceability we hold for each shipment, which is what a customer needs when a field return has to be traced back to a lot rather than to a purchase order.

Questions we answer before a reel is booked

The question we hear most is whether the 16.1 A rating can be used on a board without a heat spreader. It cannot: that is a 25 C case figure, and the still air derating is 10.2 A at 25 C ambient with the junction at 150 C, which is not a comfortable operating point. For a real product on a two layer board the number to use is nearer 7 A, and the loss at that current is 0.5 W. The second question is about the 4.5 V drive, and the answer is that the part works at that drive with 14 milliohm and a slower edge, which is fine for a load switch and not for a converter above 200 kHz.

Buyers also ask whether the body diode is adequate for a reverse battery event. At 8.2 A the drop is 0.8 V typical, which is 6.6 W in a package that sheds 2.5 W in still air, so the diode survives a short event and not a long one. A reverse polarity test on a 28 V system that lasts ten seconds will put the part at its thermal limit, and the usual answer is a series Schottky or a fuse in front of the switch rather than relying on the body diode.

On supply, we quote the reel and the tape orientation from the packing list, hold the incoming on resistance sample at both gate voltages, and where a customer needs matched parts for a parallel pair we can supply from a single date code so the threshold windows are close. That last point is worth stating before the order, because matching after the fact means sorting reels and paying for the scrap.