Contact Us

VBA2317A

Brand: VBsemi
VBsemi VBA2317A is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA2317A — Discrete & Power Semiconductors | Superb Automation

VBA2317A

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA2317A from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA2317A: a minus 30 V P channel built for load and battery switching

The VBA2317A is a single P channel MOSFET in the SO-8 body, printed at minus 30 V drain to source and plus or minus 20 V on the gate, halogen free to IEC 61249-2-21. On resistance is 0.017 ohm at a minus 10 V gate with 7 A flowing and 0.029 ohm at minus 4.5 V with 5.6 A flowing, and the typical gate charge is 13 nC at the 4.5 V point or 25 nC at 10 V. Continuous drain current is 9 A with the case at 25 C, 5.6 A at a 70 C case, and the pulsed rating is 30 A. The vendor lists two uses, load switch and battery switch, and that is exactly the pair of jobs a 30 V P channel with a 17 milliohm die does in a 12 V or 24 V product.

The package carries 2.2 nF of input capacitance and 145 pF of reverse transfer capacitance, which is a moderate ratio for a P channel and means the part does not need a shaped gate network to stay stable. Junction to ambient is 40 C per watt on a 10 second pulse and 50 C per watt maximum, junction to foot is 24 C per watt, and the dissipation is 4.2 W at a 25 C case. Those figures, not the 9 A headline, tell a buyer what a sealed enclosure will allow: at 5 A the 17 milliohm die loses 0.43 W, and the 50 C per watt path puts the junction 21 C above ambient, which is comfortable in a 60 C box and marginal in an 85 C one.

The ratings a buyer checks first

Drain to source voltageminus 30 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate, 7 A0.017 ohm
On resistance at minus 4.5 V gate, 5.6 A0.029 ohm
Continuous drain current9 A at 25 C case, 5.6 A at 70 C case
Pulsed drain current30 A
Continuous source to drain diode current3.5 A at 25 C case, 2.1 A in still air
Single pulse avalanche current7 A into 0.1 mH
Power dissipation4.2 W at 25 C case, 2.5 W at 25 C ambient
Junction to ambient, junction to foot40 and 24 C per watt typical, 50 and 30 maximum
Gate threshold voltageminus 1.0 V minimum, minus 2.5 V maximum
Total gate charge at minus 10 V and minus 4.5 V25 nC and 13 nC typical
Input, output and reverse transfer capacitance2200, 180 and 145 pF
Body diode forward voltage at 5.6 Aminus 0.71 V typical, minus 1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

Where the drive point changes the answer

The threshold window is minus 1.0 V to minus 2.5 V at 250 microamp, so on a 3.3 V rail used directly as the gate drive the worst case die has 0.8 V of overdrive and the 4.5 V resistance does not apply. In a 12 V product the gate is pulled 10 V below the source through a resistor, which gives the 17 milliohm figure, and the two rows behave very differently: 0.017 ohm against 0.029 ohm is a 70 per cent difference in conduction loss for a 5.5 V change in drive. That is the single biggest fork in the road on this part, and it is the reason a 3.3 V logic pin should drive a small N channel pull down rather than the gate directly.

Gate charge of 13 nC typical at 4.5 V and 38 nC maximum at 10 V is small enough to drive from a logic output through a 1 k resistor, and the 5.5 nC gate to drain charge keeps the Miller plateau short. The switching rows show the asymmetry that P channels always have: 10 ns turn on delay and 13 ns rise at a 10 V drive, but 23 ns turn off delay and 9 ns fall, and at a 4.5 V drive the rise stretches to 89 ns typical. A slow turn on is good for inrush into a capacitive load and bad for switching loss, and this part is clearly intended for the first case. The 30 A pulsed current with a 7 A avalanche rating covers the cable plug event on a battery switch, where the load capacitance charges through the channel in a few microseconds.

Thermal and copper effects deserve a word without touching the board itself: 40 C per watt on a 10 second pulse assumes a one inch square FR4 pad with the drain tabs soldered down, and the steady state figure of 50 C per watt maximum is the one that applies to a load switch that is on all day. With 0.017 ohm and 5 A the die loses 0.43 W, which is 21 C above ambient; with 0.029 ohm at the same current it is 0.73 W and 36 C above ambient. In an 85 C enclosure the second case reaches a 121 C junction, which is inside the 150 C rating but leaves very little for a hot day, so the drive voltage is a thermal decision as much as an electrical one.

Load switching and battery switching in practice

A battery switch is the harder of the two jobs because the load is a capacitor bank and the source is a pack that can deliver tens of amps into a short. On a 12 V product, the P channel sits in the positive lead with the gate pulled low by a resistor and pulled high by a small signal transistor to switch off, and the inrush is limited by the gate network rather than by the part. The 2200 pF input capacitance and the 13 nC gate charge make a 100 k gate resistor give a turn on that takes hundreds of microseconds, which spreads the inrush over a long enough window that the pack protection does not trip. That trick works with this die and not with a part that has 100 nC of gate charge.

A load switch on a 24 V rail is the easier job and the one where the 30 A pulse rating pays. A motor or a solenoid on a 24 V rail pulls a stall current several times its running current for a few milliseconds, and the 7 A avalanche rating into 0.1 mH is there for the unclamped kick when the switch opens. Two of these in parallel give 8.5 milliohm at a 10 V drive and split the pulse, which is the usual answer for a 15 A load that has to be switched a few times an hour. In a battery powered product the leakage matters as much as the resistance: the zero gate voltage drain current is 1 microamp at 25 C and 5 microamp at 55 C, so a switch that is off all night loses almost nothing, which is what keeps a standby budget honest.

Sourcing notes and the second source question

A minus 30 V P channel in SO-8 at 17 milliohm is a common shelf and the pin map is close to a standard, so a buyer usually has three or four candidates. Close is not equal: the gate charge varies by a factor of three across the shelf, the threshold window moves by a volt, and the reverse transfer capacitance decides whether the part rings when the load is inductive. Our pin to pin cross reference puts the gate charge and the capacitance beside the resistance so the real comparison is visible, and the eight point sequence in how to verify a drop in replacement covers the bench tests that catch the rest, including the inrush wave shape and the turn off overshoot into the actual load.

For a product that is already in production, the incoming record is what keeps a substitution honest. The plan in incoming inspection plan samples on resistance at both gate voltages, threshold at 250 microamp, and a gate charge spot check on the first lot of every date code. We hold those records per lot number, and where a customer has a qualified product we book the date code window rather than shipping whatever is on the shelf, because a P channel that is 20 per cent off on gate charge changes the inrush on a battery switch and shows up as a field failure rather than as a line stop.

Questions we answer before a reel is booked

The first question is whether the 9 A figure applies with the part on a small pad. It does not: 9 A is a 25 C case rating, and in still air the ambient derating puts the practical continuous current nearer 3 A before the junction reaches 150 C. The second is whether the body diode can be used as a blocking element. It can carry 3.5 A with the case at 25 C, but the forward drop is 0.71 V typical at 5.6 A, so a reverse battery condition through the diode is 2 W in a package that sheds 2.5 W in still air, which is a circuit that works once and not twice.

Buyers also ask about the halogen free claim. The document states compliance to IEC 61249-2-21 and to the RoHS directive, and the packing list carries the material declaration per lot, which is what a medical or automotive customer needs on file. Where a customer needs the lead frame material or the mould compound data sheet, we request it against the order rather than quoting from a general statement, because the two are not the same document and an auditor knows the difference.

On supply, the reel and the tape orientation follow the standard SO-8 outline, so a feeder change is not needed when switching from another vendor of the same body. Moisture level and floor life come from the label, and the 260 C peak soldering recommendation sits inside a normal lead free profile. For quantities below a full reel we kit the part with the rest of the bill of materials, which is the usual request from a prototype house that needs twenty pieces of six different codes.