VBA2101M
Product Specifications
VBA2101M
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA2101M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA2101M: a 100 V P channel for the high side of a DC bus
The VBA2101M is a single P channel MOSFET in the SO-8 body, printed at minus 100 V drain to source and plus or minus 20 V on the gate. On resistance is 0.110 ohm at a minus 10 V gate with 3.8 A flowing and 0.155 ohm at minus 4.5 V with 3.2 A flowing, and total gate charge is 5.65 nC at the 4.5 V point. Continuous drain current is 4.5 A with the case at 25 C, 3.6 A at a 70 C case, 2.8 A at a 25 C ambient and 2.1 A at a 70 C ambient. The vendor lists three uses: an active clamp in an intermediate DC to DC supply, an LED lighting string and a load switch. All three want the same thing, a high side switch that needs no gate rail above the supply.
A P channel at this voltage is usually chosen when the board has a 48 V to 72 V bus and the board does not want a charge pump. The gate has to be pulled 10 V below the source to reach the quoted resistance, and on a 72 V rail that means the driver sees 72 V on one side, so the gate pull down device has to be rated for the full bus. This part tolerates plus or minus 20 V of gate to source, which is what allows a simple resistor divider or a zener clamp across the gate instead of an isolated driver. That simplicity is the whole reason to take the higher resistance of a P channel over an N channel of the same die area.
The ratings a buyer checks first
| Drain to source voltage | minus 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, 3.8 A | 0.110 ohm maximum |
| On resistance at minus 4.5 V gate, 3.2 A | 0.155 ohm maximum |
| Continuous drain current | 4.5 A at 25 C case, 3.6 A at 70 C case |
| Continuous drain current in still air | 2.8 A at 25 C ambient, 2.1 A at 70 C ambient |
| Pulsed drain current, 100 microsecond | minus 20 A |
| Continuous source to drain diode current | minus 4.5 A at 25 C case |
| Single pulse avalanche energy | 11.25 mJ, avalanche current minus 15 A into 0.1 mH |
| Power dissipation | 27.8 W at 25 C case, 3.5 W at 25 C ambient |
| Junction to ambient, junction to case | 29 and 3.6 C per watt typical, 36 and 4.6 maximum |
| Gate threshold voltage | minus 1.1 V minimum, minus 2.6 V maximum |
| Total gate charge at minus 10 V and minus 4.5 V | 10.9 nC and 5.65 nC typical |
| Input, output and reverse transfer capacitance | 515, 162 and 10 pF |
| Body diode forward voltage at 3.1 A | minus 0.8 V typical, minus 1.2 V maximum |
| Junction and storage range | minus 55 to plus 150 C |
What the numbers say about the gate drive
The threshold window is minus 1.1 V minimum to minus 2.6 V maximum at 250 microamp. For a P channel that means the gate has to be pulled a full 2.6 V below the source before conduction is guaranteed on a worst case die, and 4.5 V of drive is the practical floor for any real current. On a 48 V bus the gate pull down has to swing 10 V below the source, and the 20 V gate rating gives 10 V of margin for the ringing that comes with a long gate trace. At the 4.5 V drive point the resistance is 41 per cent above the 10 V figure, so a low side gate pull down through a resistor divider costs resistance, and the divider has to be chosen for the bus voltage rather than copied from a 12 V product.
Gate charge is the bright spot. At 5.65 nC typical and 8.5 nC maximum on a 4.5 V drive, this part switches with almost no drive energy, which is why it is used as a slow high side switch rather than as a switching element. A 10 microamp pull up plus a small N channel pull down can hold the gate for a year of standby and still turn the part on in microseconds. Input capacitance is 515 pF and reverse transfer capacitance is 10 pF, an unusually low ratio, which means the drain voltage barely couples into the gate and the part is stable with a plain resistor rather than a shaped network. The penalty is speed: 10 ns turn on delay and 22 ns rise are respectable, but the fall at a 4.5 V drive stretches to 40 ns typical, and that is the edge that heats the part in a repeated switching application.
Thermal data is where this part surprises people. Junction to case is 3.6 C per watt typical, so the SO-8 can dump 27.8 W into a heat spreader at a 25 C case, but junction to ambient is 29 C per watt on a 10 second pulse and higher in the steady state, so the same part in still air only handles 3.5 W. The 11.25 mJ avalanche rating is small in absolute terms and reflects the small die, so a 48 V inductive load that is switched without a clamp will find the limit quickly. For an LED string or a load switch this is fine, because the load is resistive or the converter clamps the node; for a solenoid or a motor it is not.
Where a minus 100 V P channel is the right answer
The first case is a battery or bus disconnect on a 48 V system. A P channel sits in the positive lead, the gate is pulled to ground through a resistor to switch on, and the source sees the full bus. This part carries 2.8 A in still air at 25 C ambient with 0.11 ohm, which is 0.86 W of dissipation, so the SO-8 on a modest pad stays under a 100 C junction in a 40 C enclosure. Two of these in parallel halve the resistance and split the dissipation, and the gate threshold window is tight enough that the two share current reasonably in the linear region, which is the case that matters when they are used as an inrush limiter.
The second case is the active clamp in an intermediate bus converter, which the vendor names directly. Here the part never carries load current for long; it absorbs the leakage energy of the transformer for a few hundred nanoseconds each cycle, and what matters is the avalanche rating, the pulse current and the capacitance. An 11.25 mJ single pulse rating into 0.1 mH sets the leakage inductance budget, and the 162 pF output capacitance adds to the resonant tank, which has to be counted when the clamp voltage is calculated. The third case is an LED string in a 110 V or 120 V fixture that has been derated to a 100 V node, where the P channel gives a high side dimming switch with no gate supply and the 0.11 ohm sets the drop at 3 A to 0.33 V, small enough to leave the string current alone.
Sourcing notes and the second source question
A minus 100 V P channel in SO-8 with 0.11 ohm is a narrow shelf. Most parts at this voltage are either 0.2 ohm or are in a DPAK, so a buyer looking for a second source usually ends up comparing a SO-8 part against a larger body and has to rework the pad. Our power management cross reference lists the candidates by body and by resistance window, so the choice between a pin compatible part and a board change is visible before a sample is ordered. The rows we compare first are on resistance at 4.5 V, threshold maximum, gate charge and the avalanche rating, because those four decide whether an existing gate network still works.
For parts that are already qualified in a product, the route in last time buy and LTB planning is the one that keeps a line running when the original vendor stops the body. A minus 100 V P channel is exactly the kind of part that gets trimmed from a portfolio, because the volume is small and the die is old. We hold the cross reference and the incoming inspection record for the alternative, and where the customer cannot change the board we quote the original code with a date code window and a stock reservation instead of a substitute that needs a new pad.
Questions we answer before a reel is booked
The first question is whether the 4.5 A rating can be used with a 5 V gate drive. It can, with two conditions: the resistance becomes 0.155 ohm, which at 4.5 A is 3.1 W of dissipation, far beyond the 3.5 W ambient figure, and the threshold on a worst case die at 4.5 V of drive leaves only 1.9 V of overdrive. In practice a 4.5 A load needs a 10 V drive and a copper pad, or two parts in parallel. The second question is about the gate clamp. On a 72 V bus the gate to source voltage has to be limited, and the part tolerates 20 V, so a 15 V zener from gate to source plus a 10 k resistor to the bus is the usual network, with the zener chosen for leakage rather than for clamping current.
We are also asked whether the body diode can carry the load when the gate is off. It can, at minus 4.5 A continuous with the case at 25 C and minus 2.8 A in still air, but the forward drop is 0.8 V typical at 3.1 A, which is 2.5 W and more than the package can shed in still air. A reverse battery condition on a 48 V pack therefore needs either an external Schottky in parallel or a contactor, and this part alone is not the protection. The pulse diode current row is minus 15 A, which is a 100 microsecond figure and not a continuous one, and quoting it as a continuous rating is the most common mistake we see on this family.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, and the soldering recommendation is a 260 C peak, so a lead free reflow profile with the usual 30 second above liquidus is inside the window. Incoming inspection samples the on resistance at both gate voltages and the threshold at 250 microamp, and where a customer needs the gate charge curve for a driver setting we quote it from the same document rather than from a distributor summary.