Contact Us

VBA1805S

Brand: VBsemi
VBsemi VBA1805S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1805S — Discrete & Power Semiconductors | Superb Automation

VBA1805S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1805S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1805S: an 80 V N channel that holds 4.8 milliohm in a SO-8

The VBA1805S is a single N channel MOSFET in the SO-8 body, printed at 80 V drain to source and plus or minus 20 V on the gate. On resistance is 4.8 milliohm at a 10 V gate with 6 A flowing, and 6.0 milliohm at a 6 V gate with 5 A flowing. Continuous drain current is 16 A with the case at 25 C and 9 A once the case reaches 125 C, and the pulsed rating is 67 A. The vendor files it under DC to DC conversion and high frequency switching, which is where an 80 V part with this resistance belongs: a 48 V input rail, a telecom line card, or a synchronous stage that turns a 48 V bus into 12 V or 24 V.

The package decides the practical limit. Junction to ambient is 80 C per watt on a one inch square FR4 pad and junction to foot is 21 C per watt, so the 7.1 W dissipation quoted at a 25 C case is a case figure and not an ambient one. A board that carries 6 A through the part loses 173 milliwatt in the die at a 25 C junction, and the same 6 A at a 175 C junction loses 540 milliwatt because the resistance nearly triples over that span. That curve, not the headline current, is what sets the copper area under the drain pads.

The ratings a buyer checks first

Drain to source voltage80 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 6 A4.8 milliohm typical
On resistance at 6 V gate, 5 A6.0 milliohm typical
On resistance at 125 C and 175 C junction11 milliohm, 15 milliohm typical
Continuous drain current16 A at 25 C case, 9 A at 125 C case
Pulsed drain current67 A
Continuous source current, diode6 A
Single pulse avalanche energy125 mJ, avalanche current 50 A into 0.1 mH
Power dissipation7.1 W at 25 C case, 2.3 W at 125 C case
Junction to ambient, junction to foot80 C per watt, 21 C per watt
Gate threshold voltage2.5 V minimum, 3.0 V typical, 3.5 V maximum
Total gate charge45 nC typical, 68 nC maximum
Input, output and reverse transfer capacitance2531, 382 and 153 pF
Body diode forward voltage at 1.7 A0.72 V typical, 1.2 V maximum
Junction and storage rangeminus 55 to plus 175 C

Reading the electrical table instead of the front page

The threshold window runs 2.5 V minimum, 3.0 V typical and 3.5 V maximum at 250 microamp. A circuit that drives the gate from a 6 V rail therefore sits two and a half volts above the worst case threshold, which is real margin but not generous margin, and the on resistance at that drive is already 25 per cent above the 10 V figure. This is the part to use behind a 10 V to 12 V gate driver, or behind a charge pump, rather than directly from a 5 V logic pin. On a 5 V rail the part is below its own minimum threshold and the current it passes is leakage.

Gate charge is 45 nC typical and 68 nC maximum, with 9.9 nC of gate to source charge and 11.2 nC of gate to drain charge. That is a light load for the die size. Driving at 200 kHz from a 10 V rail costs 90 milliwatt per switch if the driver has to move the maximum 68 nC every cycle, and a small driver in a SOT-23 body covers it without a heat sink. Input capacitance is 2531 pF typical with 3165 pF maximum, and the 153 pF reverse transfer capacitance is low enough that the Miller plateau stays short at the drain voltages this part sees, so a 2.2 ohm gate resistor is usually enough to keep the edge quiet without slowing the turn off.

The switching rows were measured at 30 V with a 2.5 ohm load, 12 A and a 1 ohm gate resistor: 13 ns turn on delay, 12 ns rise, 25 ns turn off delay and 9 ns fall, all typical. Those are fast numbers for a part with 4.8 milliohm, and they are the reason a board can run at 300 kHz with little switching loss. The catch is that fast edges and a long gate loop ring, so the gate return has to sit under the driver and not across the board. The body diode is the other row to read: 0.72 V typical at 1.7 A and 1.2 V maximum, with 67 A of pulsed current, which is high enough that a hard switched half bridge can survive a short shoot through without a second clamp.

Where an 80 V part with this resistance earns its place

Telecom line cards are the natural home. The 48 V bus sits below the 80 V rating with the 20 per cent margin that a battery backed rail needs, and one part carries the full card current as a hot swap switch or as the low side of a two switch forward converter. The 125 mJ avalanche rating covers the inductive kick from a long backplane trace when the card is pulled, and the 175 C junction rating gives the thermal headroom that a sealed card cage never provides in the datasheet conditions. Two of these back to back also make a clean battery reverse protection stage on a 48 V pack, where the low on resistance matters more than the current rating because the forward drop is what heats the board.

Industrial 48 V to 12 V converters use the part as the synchronous rectifier on the secondary, and there the numbers to check are the body diode forward voltage and the reverse recovery. A 60 V or 72 V battery rail is a harder case, because a fully charged lead acid string can reach 82 V under charge, and this part is then at its limit with no margin. On a 60 V rail it is comfortable. Motor drive stages at 48 V use it as the low side switch with a gate driver that has to survive the negative spike during a phase short, which the plus or minus 20 V gate rating and the 67 A pulsed current both help with.

Sourcing notes and the second source question

The SO-8 single N channel with a 4.8 milliohm die and an 80 V rating is a crowded shelf, and vendors print the same headline resistance at different test currents. A part quoted at 4.8 milliohm at 6 A and another quoted at 4.5 milliohm at 20 A are not the same silicon, and the second will show a wider resistance window over temperature. Our pin to pin cross reference starts from the test current, the temperature coefficient and the gate charge window rather than the front page number. When a customer sends a competitor code we compare four rows first: on resistance at the actual gate voltage in use, threshold maximum, total gate charge and avalanche energy.

For a replacement that has to be proven on the customer board, the sequence in how to verify a drop in replacement covers the tests that catch the usual failures: gate ringing at the new gate resistance, reverse recovery in the low side body diode, and thermal margin at the case temperature the product actually reaches. The power management cross reference carries the pin compatible rows for this family with the gate charge and thermal resistance beside them, so a buyer can see at a glance which candidate needs a new gate resistor and which one drops in without a change to the driver.

Questions we answer before a reel is booked

Buyers ask whether the 16 A figure can be used at 25 C ambient. It cannot. It is a case temperature rating, and with 80 C per watt junction to ambient the same die in still air carries roughly 1.6 A before the junction reaches 150 C, which is the number that matters inside a sealed enclosure. The second question is whether the 175 C junction rating means the part can run hotter. It means the die survives there, not that the resistance is unchanged: at 175 C the on resistance is 15 milliohm typical, three times the 25 C figure, and any loss budget built on 4.8 milliohm has to be rebuilt at the real junction temperature.

The gate drive question comes next. A 10 V drive gives the quoted resistance and the 6 V drive gives 6.0 milliohm, so a product with only a 5 V rail needs either a small charge pump or a different part. We are also asked about avalanche. The 125 mJ figure is one pulse into 0.1 mH at 25 C with a 50 A pulse, and repeated events derate with junction temperature and repetition rate, so a clamp diode is still cheaper than a warranty return on a rail that switches an inductive load every cycle.

Availability is quoted per reel with the date code printed on the label, and the incoming inspection record for each lot includes an on resistance sample at the 4.5 V and 10 V gate points. A build that needs a specific date code window for an already qualified product has to book it before the order is placed, because a mixed shipment is the usual reason a line stops for a re qualification nobody planned. Reel size and reel material are stated on the packing list, and the SO-8 tape orientation follows the standard EIA outline, so no change to the feeder setup is needed.