VBA1606
Product Specifications
VBA1606
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1606: 4.8 milliohm at 60 V in an SO-8, rated to 175 C
The VBA1606 is a single N channel MOSFET in the SO-8 body, printed at 60 V drain to source and plus or minus 20 V on the gate, with 4.8 milliohm at a 10 V gate and 6 milliohm at 6 V. It carries 16 A at a 25 C case and 9 A at 125 C, with 67 A pulsed, 125 mJ of single pulse avalanche energy at 50 A, and a 175 C junction limit. The vendor states 100 per cent gate resistance and unclamped inductive switching testing, and the sheet carries a note that parametric verification is ongoing, which a buyer should read as a caveat on the secondary rows rather than on the headline.
A 60 V, 4.8 milliohm die in an SO-8 is a part for a 48 V rail where the current is 10 to 15 A and the board has no room for a TO-252. The 175 C junction is the other reason to choose it: a product in a sealed housing that reaches 105 C case still has 70 degrees of margin, and the resistance at 175 C is quoted rather than left to a curve.
The ratings that decide the application
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 4.8 milliohm at 6 A |
| On resistance at 6 V gate | 6 milliohm at 5 A |
| On resistance at 125 C | 11 milliohm at 6 A |
| On resistance at 175 C | 15 milliohm at 6 A |
| Continuous drain current | 16 A at 25 C case, 9 A at 125 C case |
| Pulsed drain current | 67 A |
| Continuous source current, diode | 6 A |
| Single pulse avalanche energy | 125 mJ into 0.1 mH at 50 A |
| Power dissipation | 7.1 W at 25 C case, 2.3 W at 125 C case |
| Junction to ambient | 80 C per watt on a one inch board |
| Junction to foot, drain | 21 C per watt |
| Gate threshold voltage | 2.5 V minimum, 3.0 V typical, 3.5 V maximum |
| Total gate charge at 10 V | 45 nC typical, 68 nC maximum |
| Body diode forward voltage | 0.72 V typical, 1.2 V maximum at 1.7 A |
Reading the rows rather than the front page
The threshold window is tight and high: 2.5 V minimum, 3.0 V typical and 3.5 V maximum at 250 microamp. That is the signature of a die with a thick gate oxide and a high channel doping, and it means a 4.5 V drive gives only 1 V of overdrive on a worst case part, which is not enough to reach the 6 milliohm figure. A 10 V drive is the assumption in every switching row of the sheet, and a board that drives from 5 V should use the 6 V column at best and expect more.
The resistance rows carry three temperatures and they move a long way: 4.8 milliohm at 25 C, 11 milliohm at 125 C and 15 milliohm at 175 C at the same 6 A test current. That is 2.3 times and 3.1 times the cold figure, so a conduction loss budget written from the front page is optimistic by a factor of three in a hot enclosure. At 12 A the loss rises from 0.7 W to 1.6 W to 2.2 W across that range, and a product that runs at 105 C case has to use the second number.
Gate charge is 45 nC typical and 68 nC maximum at 10 V, with 9.9 nC of gate to source and 11.2 nC of gate to drain charge, and the input capacitance is 2531 pF typical and 3165 pF maximum with 382 pF of output and 153 pF of reverse transfer. That is a substantial load: at 300 kHz a 68 nC gate at 10 V draws 204 milliwatt of drive power and needs a driver that can deliver 1 A peaks without drooping. The gate resistance window of 0.40 to 1.30 ohm is narrow, which is good for repeatability and bad for damping: an external resistor of 2 to 5 ohm is usually needed to keep the drain ring inside the 60 V rating.
Switching times are 13 ns turn on delay, 12 ns rise, 25 ns turn off delay and 9 ns fall into a 2.5 ohm load with a 10 V drive and a 1 ohm gate resistor. The fall time of 9 ns at 12 A and 30 V is a 40 V per nanosecond slew, which is fast enough to excite the parasitic inductance of a source return and to radiate. A board with a poor return path will show ringing above 60 V on the drain, and that is the failure mode to look for in a first article rather than in a field return.
Where a 60 V SO-8 with a 175 C junction fits
The first use is a 48 V telecom or industrial rail with a 10 to 15 A load, where the 60 V rating covers the 57 V maximum of a PoE type 4 port and the 16 A case rating covers the current. The second is a synchronous rectifier on the secondary of a 48 V input converter, where the 125 mJ avalanche rating absorbs the leakage spike without a snubber in most builds. The third is a battery disconnect on a 48 V pack, where the 175 C junction gives margin in a sealed enclosure and the 4.8 milliohm keeps the drop under 100 mV at 15 A.
In a motor drive the part works as the low side switch for a 36 V or 48 V brushless motor, and the 67 A pulse covers the stall current of a small drive. The 80 C per watt junction to ambient sets the continuous current at around 1.5 A in still air without extra copper, so the practical use is with a copper pour and a fan, or with a duty cycle that keeps the average loss low.
Sourcing notes and the second source question
A 60 V part at 4.8 milliohm with a 175 C junction is a narrow class, and the substitutes usually differ in threshold rather than in resistance. A part with a 1.5 V threshold will turn on harder from a 5 V drive and may switch faster, which changes the emissions profile of the whole product. Our pin to pin cross reference starts from the pad and the pin map, then compares threshold, on resistance at the drive voltage and gate charge before anything else.
The vendor note that parametric verification is ongoing deserves a process rather than a doubt: the secondary rows of a new die are the ones that move between wafer lots, so the incoming check should sample on resistance at 10 V, threshold and avalanche on the first lot of any new date code. The framework for that is in supplier quality audit, which covers what to ask a vendor for and what to measure when the answer is a document rather than a test report. We supply this code with the date code on the reel label and hold the vendor test record per lot where the customer asks for it.
Questions we answer before a reel is booked
The first question is whether 16 A can be held continuously. It can at a 25 C case and 9 A at 125 C, and with 80 C per watt junction to ambient on a one inch board the ambient figure is far lower. A product that runs at 12 A needs the copper and a fan, or a larger package. The second question is whether the part can be driven from 5 V. It turns on, because the threshold maximum is 3.5 V, but the resistance is closer to the 6 V column than to 4.8 milliohm, and the switching times stretch.
The third question is about the 125 mJ avalanche rating, which is large for an SO-8. It is a single pulse at 25 C into 0.1 mH at 50 A, and it derates with junction temperature; a board at 125 C has roughly a third of that. The fourth is the diode: 6 A continuous is the same as the 125 C channel rating, which is unusual and reflects a wide body diode in this die, so a synchronous stage can rely on the diode during a long dead time more than on most parts in this body.
On supply, this code is a catalogue item with the reel size and date code on the label. We hold an incoming record with an on resistance sample at 10 V and a threshold sample, and where a customer needs a specific date code for a qualified build, the booking has to be made before the order is placed.