Contact Us

VBA1410

Brand: VBsemi
VBsemi VBA1410 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1410 — Discrete & Power Semiconductors | Superb Automation

VBA1410

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1410: a 40 V N channel in an SO-8 for synchronous rectification

The VBA1410 is a single N channel MOSFET in the SO-8 body, printed at 40 V drain to source and plus or minus 20 V on the gate, with 14 milliohm at a 10 V gate and 16 milliohm at 4.5 V. It carries 10 A at a 25 C case, 8 A at 70 C, 10.4 A at a 25 C ambient and 8.8 A at 70 C, with 50 A pulsed and 11 mJ of single pulse avalanche energy at 15 A. The vendor lists synchronous rectification, POL and intermediate bus converters as the applications, and the secondary side of an isolated converter is where this die fits best.

Compared with its 3.8 milliohm sibling, this part gives up resistance for a lower price point and a smaller die, and the trade is worth making where the current is 8 to 10 A rather than 15 A. The drain is on four pins and the source on three, so the package resistance is low for the body and the thermal path runs into the board through the leads and the exposed pad area.

Ratings and the numbers behind them

Drain to source voltage40 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate14 milliohm at 12.4 A
On resistance at 4.5 V gate16 milliohm at 10.8 A
Continuous drain current10 A at 25 C case, 10.4 A at 25 C ambient
Continuous drain current at 70 C8 A at the case, 8.8 A in ambient
Pulsed drain current50 A
Continuous source current, diode5 A at 25 C case, 2.1 A at 25 C ambient
Single pulse avalanche energy11 mJ into 0.1 mH at 15 A
Power dissipation6 W at 25 C case, 2.5 W at 25 C ambient
Junction to ambient, 10 second pulse37 C per watt typical, 50 maximum
Junction to ambient, steady state85 C per watt maximum
Junction to foot, drain17 C per watt typical, 21 maximum
Gate threshold voltage1.0 V minimum, 3.0 V maximum
Total gate charge at 10 V15 nC typical, 23 nC maximum
Body diode forward voltage0.8 V typical, 1.2 V maximum

Reading the rows rather than the front page

The threshold window is 1.0 V to 3.0 V at 250 microamp, so a 4.5 V drive is comfortable and a 3.3 V logic pin is marginal on a worst case die. The gate charge is 15 nC typical and 23 nC maximum at 10 V, with 6.7 nC of gate to source and 5.1 nC of gate to drain charge, and the input capacitance is 2000 pF with 260 pF of output capacitance and 150 pF of reverse transfer. The higher reverse transfer than its low resistance sibling is the price of the smaller die: the Miller plateau is wider and the part is slower to switch, which matters at 500 kHz but not at 100 kHz.

Switching times are given for a 4.5 V drive and a 10 V drive. At 4.5 V the turn on delay is 25 ns, rise 12 ns, turn off delay 25 ns and fall 10 ns; at 10 V the delays become 10 ns and 30 ns and the rise 15 ns. The turn off delay of 30 ns at 10 V is long for a part this size, and it comes from the 5.1 nC of gate to drain charge: the gate node sits on the Miller plateau while the drain voltage slews, and the time it spends there is set by the external gate resistor and the driver current. A driver that cannot source 1 A will stretch that delay and the loss with it.

The thermal side is straightforward. Junction to ambient is 37 C per watt for a 10 second pulse and 85 C per watt in the steady state on a one inch board, with 6 W at a 25 C case and 2.5 W in a 25 C ambient. At 8 A and 14 milliohm the conduction loss is 0.9 W, which puts the junction 76 degrees above ambient in still air, and that is why the 70 C ambient rating drops to 8.8 A even though the 25 C ambient figure is 10.4 A.

The body diode carries the inductor current during dead time and its forward voltage is 0.8 V typical. Continuous diode current is 5 A at a 25 C case and 2.1 A at a 25 C ambient. In a secondary side rectifier the diode conducts for the whole off time, not just the dead time, if the topology is a diode rectifier and this part replaces a diode. That use is possible at 2 to 3 A and not at 10 A, because the diode drop at 10 A would be 8 W.

Where a 40 V SO-8 earns its place

The first use is the secondary side of an isolated converter with a 24 V output, where the 40 V rating covers the ringing of the leakage inductance and the 14 milliohm keeps the loss reasonable at 8 A. The second is a POL converter on a 12 V rail, where the duty cycle is low and the conduction loss is small. The third is a load switch or a battery disconnect on a 24 V pack, where the 50 A pulse covers the inrush into a large capacitor and the 11 mJ avalanche rating covers a short cable.

In a small motor drive the part works as the low side switch, and the diode rating of 5 A at a 25 C case sets the limit for a stall event. A brushed motor that stalls at 8 A will exceed it, and the answer is a current limit or a higher rated part rather than a bigger heat sink.

Sourcing notes and the second source question

This part sits in the middle of the 40 V SO-8 range, between the 3.8 milliohm parts and the 20 milliohm parts, and it is often chosen for price rather than for a specific electrical reason. That makes it a good candidate for a second source, because the rows that differ between vendors mostly affect switching rather than conduction, and a customer can qualify a substitute on gate charge and diode recovery without changing the board. Our power management cross reference tables those rows at the drive voltage the customer uses.

Where the part is a substitute for a competitor code, the tests that catch a bad match are the ones in how to verify a drop in replacement: a full load thermal soak with the case thermocouple where the part actually mounts, a short circuit or stall event, and a check of the drain ring at the highest input voltage. We supply this code with the matching gate resistor and, where the quantity allows, from one date code for the qualification and the build.

Questions we answer before a reel is booked

The first question is why the case rating is 10 A and the ambient rating is 10.4 A, which looks backwards. It is a rounding effect: both rows are limited by the package and the board, and the vendor has printed the ambient row at a 10 second pulse with a large copper pad while the case row assumes an infinite heat sink that the body cannot use. The honest number for a product in a box is 8 to 9 A. The second question is whether 4.5 V drive is enough. It is, at 16 milliohm, which is 14 per cent worse than at 10 V, and in a secondary side rectifier at a 50 per cent duty cycle the total loss rises by about 7 per cent.

The third question is about the avalanche rating of 11 mJ. It is smaller than the 20 mJ of the low resistance sibling because the die is smaller, and a 24 V converter with a one metre cable will exceed it on a hard switch off. A clamp or a soft start is the answer, not a bigger part. The fourth is the diode: 5 A at a 25 C case is a dead time and light load figure, and a rectifier that runs the diode continuously should use a part with a lower forward voltage or a synchronous scheme.

On supply, this code is a catalogue item, and we hold the incoming record for each lot with an on resistance sample at 4.5 V. A customer who needs a specific date code for a qualified product should book it before the order, because the reel label is the only place the code is recorded.