HXNM40007
Product Specifications
HXNM40007
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXNM40007 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXNM40007: ten watts at 4.4 to 5 GHz with twenty six decibels of gain
The HXNM40007 is the high gain member of the Hisiwell group that covers the lower C band. The vendor index row reads 4.4 to 5 GHz, saturated output at least 40 dBm, gain at least 26 dB, drain efficiency at least 45 per cent, 28 V drain rail, continuous wave. That is 10.00 W across 600 MHz with a gain floor fourteen decibels above the standard part on the same band.
The comparison with the standard family is the useful way to read it. HXN40048 covers the same 4.4 to 5 GHz window at the same 40 dBm and the same 28 V with 12 dB of gain. This part offers 26 dB, which halves the drive requirement from 28 dBm to 14 dBm, which is 25 mW instead of 631 mW.
The power budget is the same on both parts. At 45 per cent efficiency 10.00 W of output draws 22.2 W from the rail, which is 0.794 A at 28 V, and leaves 12.2 W of heat. The difference between the two parts is entirely in the input side, not in the output side or the thermal side.
Six hundred megahertz at a 4.7 GHz centre is 12.77 per cent fractional bandwidth, which covers the 4.4 to 5 GHz fixed link allocations and the lower half of the C band satellite window. It is a narrower window than the S band members of the family, and the gain is 2 dB lower than the 28 dB at 3.1 GHz, which is the usual pattern as frequency rises.
The parameter rows Hisiwell publishes for HXNM40007
| Part class | Gallium nitride power transistor, internally matched, high gain family |
| Frequency range | 4.4 to 5 GHz |
| Bandwidth, calculated | 600 MHz, 12.77 per cent fractional at a 4.70 GHz centre |
| Saturation output power as published | at least 40 dBm |
| Saturation output power in watts, calculated | 10.00 W |
| Gain as published | at least 26 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | not published, the index prints a slash in that column |
| Operating mode | continuous wave |
| Output at 1 dB compression | not published, the index prints a slash in that column |
| DC input at saturation, calculated | 22.2 W |
| Drain current at saturation, calculated | 0.794 A at 28 V |
| Dissipation at saturation, calculated | 12.2 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 15.0 W |
| Drive power for the rated output, calculated | 14 dBm, 25.1 mW |
| Output per 100 MHz of the band, calculated | 1.67 W |
| Load voltage at saturation into 50 ohm, calculated | 22.4 V RMS, 31.6 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Stability data and load mismatch tolerance | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Orderable addendum and packing | not published |
| Family neighbour at 43 dBm on the same band | HXNM40008, same rail, 23 dB gain |
Twenty six decibels against twelve on the same window
The standard part on this band needs 28 dBm of drive, which is 631 mW, and that is one whole amplifier stage in front of it. The high gain part needs 14 dBm, which is 25 mW, and that is a single MMIC or a modem output. The saving is one stage, one bias network and one interstage match.
What the extra gain costs is bandwidth. The standard part at 12 dB holds plus or minus 0.8 dB across the 600 MHz and the high gain part publishes no flatness figure at all. A wide match with high gain is harder to hold flat, and the vendor appears to have chosen not to publish a number rather than to publish a loose one.
The stability question is more acute at 26 dB than at 12 dB. A high gain part behind a filter that goes reactive out of band will find a return path, and without vendor stability data the build has to assume the worst case. A 3 dB pad at the input costs a third of the available drive margin and buys 6 dB of return loss at every frequency, which is often the cheapest cure.
The gain also sets the noise contribution of the stage. At 26 dB the following stage contributes almost nothing to the cascade noise figure, so a system that has to meet a noise budget can put this part close to the antenna and accept a modest front end noise figure. The vendor publishes no noise figure, so that reading is a structure rather than a number.
The 4.4 to 5 GHz window and what sits in it
The 4.4 to 5 GHz fixed link allocations are the primary commercial use. A 10 W stage with 26 dB of gain and 25 mW of drive is a natural fit for an outdoor unit, where the modem output is 10 to 15 dBm and the antenna is a dish with 30 dB or more of gain.
The lower half of the C band satellite window also sits inside the range. For a satellite terminal the linearity matters more than the saturated output, and with no compression point published the backoff has to be measured. A 10 W part run at 2.5 W is the usual configuration for a multicarrier uplink.
The band is also used for laboratory instrumentation and for radar test sets. For those the continuous wave rating and the gain are the two figures that matter, and the 600 MHz window means a swept measurement does not need a band change in the middle.
Where the system has to cover 4.4 to 5 GHz and beyond, the standard family offers HXN43004 at 51 dBm across 4.4 to 6.7 GHz with 8.5 dB gain. It is a different architecture: much more output, much less gain, and a window twice as wide.
Heat, feed and the output network
12.2 W of heat is within reach of a board level carrier, and the number to work against is the worst case at 40 per cent efficiency, which is 15.0 W. On 5 C per watt the rise at that figure is 75 C over the case, and on 3 C per watt it is 45 C. At a 70 C ambient the first option is outside a 100 C limit and the second is inside it.
The drain feed carries 0.794 A at 28 V, which is a trace width question rather than a copper bar question. The decoupling bank has to hold the rail through the envelope of the modulation, and for a continuous wave carrier that is a simpler requirement than for a pulsed one.
The output voltage at 22.4 V RMS and 31.6 V peak is above the 28 V rail, so the output network and the connectors have to be rated above 31.6 V at 4.7 GHz. A connector that is fine at 1 GHz may not be fine here, and the vendor publishes no load mismatch tolerance to bound the worst case.
An isolator at the output is the conventional protection on a 10 W stage. It costs 0.4 to 0.6 dB of insertion loss and it turns a disconnected antenna into a reflected load the isolator absorbs rather than the transistor. On a part with 26 dB of gain the isolator also helps stability.
What to settle before the part goes on a board
The gate bias point is not published. With 26 dB of gain the bias sweep is the first bench task, and the chosen quiescent current should be recorded with the gain and the compression point at that current, not with the gain alone.
The second item is the input match to the source. At 14 dBm of drive the source is a small amplifier whose own output match may not be 50 ohm, and a 26 dB part is sensitive to what it sees. A pad at the input fixes both the match and the stability in one component.
The third item is packing. No addendum, no reel size and no moisture level are published, so the purchase order names the band, the rail and the quantity and the factory confirms the rest. For a build that runs over months the confirmation should include the lot and the date code so the parts can be traced.
Where a customer is comparing this part against the standard 12 dB member, the two are not drop in replacements even though the output and the band match. Our pin to pin cross reference page sets out why the drive level and the stability margin have to be checked before a substitution is accepted.
Questions buyers ask about HXNM40007
Is the 26 dB gain available at the band edges. The vendor prints a minimum, which normally means across the stated window. No flatness figure is published, so the variation across the 600 MHz has to be measured.
Can it replace HXN40048. Electrically the output, the rail and the band match. The drive level does not: 14 dBm against 28 dBm. A chain built around the standard part will overdrive this one by 14 dB unless the driver is changed.
What happens at 5.2 GHz. That is outside the stated window. The match is synthesised for 4.4 to 5 GHz and the vendor gives no data above it, so operation there is untested.
How is it supplied. With no published packing or moisture level, the confirmation comes from the factory with the order. The part sits on the RF procurement line with the rest of the C band family, and the schedule depends on the factory lot rather than on a distributor shelf.