Contact Us

HXN50117

Brand: Hisiwell
Hisiwell HXN50117 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN50117 — Discrete & Power Semiconductors | Superb Automation

HXN50117

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN50117 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN50117: 40 W continuous from DC to 4 GHz on a 50 V rail

The HXN50117 is the smallest of the three unmatched gallium nitride HEMTs that Hisiwell files on a DC to 4 GHz window and a 50 V rail. The saturation row reads 40 W and the mode column reads continuous wave, which places it below the HXN50118 at 50 W and the HXN50120 at 80 W on the same window, with the same blank gain and blank efficiency columns that the whole group carries.

40 W is 46.02 dBm by calculation. Into 50 ohm it needs 44.7 V RMS, or 63.2 V peak, which is 1.27 times the 50 V rail. That is the lowest peak to rail ratio of the three, and it is the practical reason this member is the easiest of the group to run from a supply that sags under load: the headroom between the peak swing and the rail is smaller, so a rail that drops from 50 V to 46 V under keying eats less of the operating margin.

The row publishes no gain and no efficiency, and the product page publishes no parameter table of its own, only a picture of one. A quotation therefore cannot carry a drive level, a DC current or a heat figure until the data sheet is in hand, and the enquiry should ask for it in the same message rather than after the price.

The HXN50117 rows as the vendor publishes them

Part classGallium nitride HEMT power transistor, unmatched
Frequency range, index rowDC to 4 GHz
Band ratio, calculated4 to 1
Saturation output, index row40 W
Saturation in dBm, calculated46.02 dBm
Output per gigahertz of window, calculated10.0 W
Drain rail, index row50 V
Load voltage at 40 W into 50 ohm, calculated44.7 V RMS, 63.2 V peak
Peak swing against the rail, calculated1.27 times
Mode, index rowContinuous wave
Modes the product page claimsContinuous wave, pulsed and any modulation
GainNot published on the index row
Drain efficiencyNot published on the index row
Package and bodyNot published on the product page
Thermal resistance, junction to caseNot published
Gate bias point and quiescent currentNot published
Load impedance at the outputNot published, no load pull table on the page
Applied application listWireless communication infrastructure, wideband amplifier, EMC testing, ISM
Data sheet link on the product pageA parameter image only, no linked document
Orderable addendumNone published
Packing quantity and moisture levelNot published

The three DC to 4 GHz members, read as one family

Hisiwell publishes three parts on this window with one rail and one mode, and the only column that separates them on the index page is the watt figure. The gaps are 0.97 dB between the 40 W and the 50 W member and 3.01 dB between the 40 W and the 80 W member. A 3 dB step is a doubling of drive and a doubling of heat, so the 80 W member is not a plug in upgrade for the 40 W member; it is a different thermal arrangement and usually a different driver.

Because gain is blank on all three rows, the family cannot be compared on drive from the catalogue. What can be compared is the load voltage. The 40 W member swings 63.2 V peak at the load, the 50 W member 70.7 V and the 80 W member 89.4 V. Those numbers scale with the square root of power, so the 80 W member needs 41 per cent more peak voltage than the 40 W member, which shows up as a higher drain bias headroom requirement, a wider output network and a larger creepage distance on the board.

Where a programme needs a published gain and efficiency column at the same band, the shelf offers the HX04200F at DC to 4 GHz, 200 W, 48 V, with 20 dB and 70 per cent printed on the row. That part is four times the power of this one and on a different rail, so it is not a substitute, but it is a reference point for what a fully populated row looks like on this shelf, and it is the comparison most buyers make when they ask why one row has numbers and another does not.

Choosing between 40 W, 50 W and 80 W on one board

The decision is usually set by the driver, not by the antenna. If the chain in front of the final stage delivers 1 W, a 13 dB part reaches 20 W and a 16 dB part reaches 40 W, so the same driver can serve either the 40 W or the 50 W member depending on the gain that the data sheet eventually shows. Where the chain delivers 2 W, the 80 W member becomes reachable and the question turns to heat.

Heat is the second lever. At a nominal 55 per cent drain efficiency the 40 W member draws about 73 W from the rail, which is 1.45 A at 50 V and 33 W of heat; the 80 W member at the same efficiency draws about 145 W, which is 2.9 A and 65 W of heat. Those two figures differ by a factor of two in the same package footprint, so the copper area and the heatsink interface have to be sized for the member that will actually ship and not for the smallest one on the shelf.

Band position is the third. A part used at 500 MHz and the same part used at 3.9 GHz are two different thermal problems, and the vendor publishes no curve to say how different. Where the application runs at the top of the window and the duty cycle is high, the conservative route is to start on the 40 W member, measure the case temperature at the intended output, and move up only if the margin allows.

What an order for the HXN50117 has to state, and what it cannot yet

There is no orderable addendum for this part, no reel size, no marking and no moisture level on the public page. A purchase order has to carry the part number, the quantity, the band, the mode, the rail and the bias condition, and the factory has to confirm each back in writing. A line that carries only a part number and a quantity leaves the body and the test condition open, and on an unmatched die those two are exactly what the board is built around.

The quantity question is more than a price tier. Where the programme is a prototype build, the reel size decides whether the buyer takes a full reel or a cut tape, and cut tape on a die this size is a handling risk that has to be agreed before the material is picked. Where the programme is production, the packing question becomes a line side question, because a reel that does not fit the feeder stops the line regardless of the price.

Lead time cannot be quoted from the page. Nothing published states a schedule, a minimum quantity or a factory location for this row. Reporting that honestly is more useful than a headline number, because a schedule invented at the quotation stage turns into a missed date at the delivery stage.

Questions buyers ask about the HXN50117

Are the 40 W and 50 W members the same die at different bias? Nothing published says so, and the two rows carry different watt figures in the same window and rail, which is consistent with either a different die or a different screening. Treating them as one part at two bias points would be an assumption, and the assumption is not supported by the page.

Does the part need a negative gate supply? Almost certainly yes at this class, because a depletion mode GaN HEMT needs the gate held below the source before the drain is energised. The vendor does not publish the pin voltages on this row, so the sequence has to come from the data sheet, and a bias board that applies drain before gate will destroy the part on the first switch on.

Is pulsed operation allowed above the continuous figure? The product page says pulsed is supported and publishes no pulse figure, no pulse width and no duty cycle. That combination means pulsed use is possible but the ceiling is unknown, and any pulse rating a buyer needs has to be confirmed by the factory against a stated pulse width and duty.

Where can the part be bought with a traceable batch? The sourcing route for a small die like this is a distributor with an unbroken chain back to the factory, and the incoming check has to cover the marking, the body and a curve trace at the intended band. The RF component sourcing page describes that chain, and the one stop RF supply page covers how a mixed bill with driver stages and passives is consolidated around it.