HXN40062
Product Specifications
HXN40062
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40062 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40062: ten watts across 5.3 to 5.9 GHz
The HXN40062 sits one rung above the five watt member of the same band. The vendor index row reads 5.3 to 5.9 GHz, saturated output at least 40 dBm, gain at least 12 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave. That is 10.00 W across 600 MHz, on the same rail and with the same gain floor as the smaller part.
The step from five to ten watts doubles the DC input and the dissipation. At 45 per cent efficiency the draw is 22.2 W from the rail, which is 0.794 A at 28 V, and the heat is 12.2 W. The gain and the band do not change, which is what makes the pair usable as a family inside one product line with a single bias and a single thermal solution per power level.
The drive for rated output is 28 dBm, which is 0.631 W. That is a level a packaged driver reaches directly and a level a discrete two stage chain reaches with margin, so the part can be the only power stage in a small transmitter.
Ten watts is also the level where the output stops being casual. 10.00 W into 50 ohm is 22.4 V RMS and 31.6 V peak, which is above the 28 V rail. Output networks, connectors and test cables all have to be rated above 31.6 V at 5.6 GHz, and a bench built for the five watt member will not necessarily do.
The parameter rows Hisiwell publishes for HXN40062
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 5.3 to 5.9 GHz |
| Bandwidth, calculated | 600 MHz, 10.71 per cent fractional at a 5.60 GHz centre |
| Saturation output power as published | at least 40 dBm |
| Saturation output power in watts, calculated | 10.00 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Output at 1 dB compression | not published, the index prints a slash in that column |
| DC input at saturation, calculated | 22.2 W |
| Drain current at saturation, calculated | 0.794 A at 28 V |
| Dissipation at saturation, calculated | 12.2 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 15.0 W |
| Drive power for the rated output, calculated | 28 dBm, 0.631 W |
| Output per 100 MHz of the band, calculated | 1.67 W |
| Load voltage at saturation into 50 ohm, calculated | 22.4 V RMS, 31.6 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour on the same band at 37 dBm | HXN40061, same rail, same gain floor |
What doubles when the power doubles
The DC input goes from 11.1 W to 22.2 W and the heat from 6.1 W to 12.2 W. What does not double is the external hardware: the connectors, the output filter and the bias tee all carry the same band and the same 50 ohm, so the only changes are the current rating of the feed and the size of the thermal path.
Twelve watts of heat is still within the reach of a board with a copper paddle and a via field, provided the paddle is tied to a sink rather than to free air. On a carrier offering 5 C per watt the rise is 61 C over the case, which at a 70 C ambient puts the case at 131 C and the junction higher still. On 3 C per watt the rise is 37 C and the same ambient gives a case at 107 C.
The efficiency row is a minimum, so the dissipation figure is a worst case at 45 per cent. If the real part runs at 50 per cent the heat falls to 10.0 W, and if it runs at 40 per cent it rises to 15.0 W. A proposal that quotes the middle of that range is quoting a number nobody measured.
Backing off 6 dB for linear operation gives 2.51 W of average output and, at an assumed 30 per cent efficiency in backoff, 5.86 W of heat. That is the operating point of a link that runs below saturation, and it is the reason a 10 W part often sits in a 2 W application with a comfortable thermal margin.
The 5.3 to 5.9 GHz window in practice
Six hundred megahertz at 5.6 GHz covers the 5.4 GHz WLAN channels, the 5.8 GHz ISM band and the 5.85 to 5.925 GHz vehicle link allocation. A single amplifier covering all three means one product can be configured for several markets by changing a filter rather than by changing the power stage.
The flatness figure applies across the whole window, so the edge at 5.9 GHz is as much a working point as the centre. In a link budget the edge case sets the drive and the antenna gain, and the mid band then sits above target, which is the direction the budget wants.
Where the system has to cover 5.0 to 5.9 GHz rather than 5.3 to 5.9, the same vendor offers HXN43005 at 47 dBm with 10.5 dB gain and 52.4 per cent efficiency. It adds 100 MHz at the bottom of the band, seven decibels of output and loses 1.5 dB of gain against this part.
Where the system is a radar rather than a link, the same band carries no primary allocation and the part is used in test equipment or in laboratory instrumentation instead. For that use the continuous wave rating and the 12 dB gain floor are the two figures that matter, and the flatness is what keeps a swept measurement honest.
Bias, matching and first article work
The gate bias is not published. The vendor gives the drain rail, the efficiency and the gain, and nothing about the gate. The first article is therefore a bias sweep against drain current, with the quiescent point chosen for the linearity the application needs. A class AB point at a few per cent of the maximum drain current is the usual starting place for a modulated signal.
The input and output are internally matched to 50 ohm according to the vendor description, which means the external network is a filter and a bias tee rather than a tuning network. That saves a tuning step, and it also means the part cannot be trimmed to a narrow band if a customer wants more gain from the same die.
The load mismatch tolerance is not published. At 31.6 V peak into a matched load, a 2 to 1 mismatch can push the drain voltage towards twice the rail, and there is no figure from the vendor to say what the part survives. An isolator at the output costs insertion loss and buys certainty, and on a 10 W stage at 5.6 GHz the trade is usually worth taking.
Where the part is being compared against a 10 W stage from another vendor, the fields that matter are the rail, the mode, the band, the gain floor and the flatness window. Our RF power transistor cross reference page sets out that comparison and the order in which the fields should be checked.
Questions buyers ask about HXN40062
Is it continuous wave at full output. The index row says continuous wave and the mode column carries no pulse condition, so the 40 dBm is a steady state figure. The 12.2 W of dissipation is a steady load rather than an average over a duty cycle.
Can it be used in a pulsed system. It can, and the thermal margin improves because the average dissipation falls with the duty cycle. What does not improve is the peak drain voltage, which stays at 31.6 V into a matched load regardless of duty.
Does it come with scattering parameters. No. The vendor publishes an index row and a product page and no data sheet, so there are no S parameters, no load pull contours and no thermal derating curves. Everything on this page that is not in those two sources is marked calculated.
How is it ordered. With no addendum and no packing column on the vendor page, the purchase order names the band, the rail and the quantity and the factory confirms packing. The part sits on the one stop RF supply line with the rest of the 5 GHz family, so a build that needs several members can be consolidated into one shipment.