Contact Us

HXN40050

Brand: Hisiwell
Hisiwell HXN40050 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40050 — Discrete & Power Semiconductors | Superb Automation

HXN40050

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40050 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40050: fifty watts at 4.4 to 5 GHz, the first rung with an 11 dB gain floor

The HXN40050 is the fourth member of the Hisiwell 4.4 to 5 GHz ladder and the point where the gain floor starts to fall. The published row reads 4.4 to 5 GHz, saturated output at least 47 dBm, gain at least 11 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave. Both ports are 50 ohm, matched by in plane synthesis on a film hybrid carrier.

Fifty watts of radio frequency at 45 per cent efficiency draws 111.4 W from the 28 V rail, which is 3.98 A, and leaves 61.3 W of dissipation on the flange. Drive at the 11 dB gain floor is 36 dBm, four watts. Those two figures together are the reason this rung is a system decision rather than a part swap: a four watt driver and a heatsink that removes sixty watts are both real costs.

The output voltage into 50 ohm at saturation is 50.1 V RMS and 70.8 V peak, more than twice the drain rail. Every connector, cable, coupler and attenuator in the test path has to be rated for that, and a bench built around a ten watt part will not survive a fifty watt stage without an attenuator at the output.

This is the level where a single ended stage is replaced by a balanced pair in most product lines. Two of these combined with a 3 dB hybrid give 100 W with a softer load per device, and the reflected power from a bad antenna is shared rather than absorbed by one carrier. The RF component sourcing page covers how we quote the pair plus the combiner as one bill of materials.

The parameter rows Hisiwell publishes for HXN40050

Part classGallium nitride power transistor, internally matched
Frequency range4.4 to 5 GHz
Bandwidth, calculated600 MHz, 12.8 per cent fractional at a 4.70 GHz centre
Saturation output power as publishedat least 47 dBm
Saturation output power in watts, calculated50.12 W
Gain as publishedat least 11 dB
Drain efficiency as publishedat least 45 per cent
Drain voltage28 V
Flatness across the bandplus or minus 0.8 dB
Operating modecontinuous wave
Input impedance50 ohm
Output impedance50 ohm
Match technology as described by the vendorin plane matching synthesis, film hybrid integration
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated111.4 W
Drain current at saturation, calculated3.98 A at 28 V
Dissipation at saturation, calculated61.3 W
Dissipation if efficiency falls to 40 per cent, calculated125.3 W
Drive power for the rated output, calculated36 dBm, 3.98 W
Output per 100 MHz of the band, calculated8.35 W
Load voltage at saturation into 50 ohm, calculated50.1 V RMS, 70.8 V peak
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text, one image on the product page
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour on the same band at 43 dBmHXN40049, same rail, 12 dB gain
Neighbour on the same band at 50 dBmHXN40051, same rail, 10 dB gain

Sixty one watts of heat decides the mechanical envelope

61.3 W on a 3 C per watt carrier rises 184 C over the case, which is already beyond any junction limit, and on a 5 C per watt carrier it is 306 C. This part cannot be run at saturation on a carrier of that class. It needs a metal carrier with a low thermal resistance and a sink that holds the case under 80 C in the ambient of the enclosure, which in practice means a copper or aluminium block and forced air or a cold plate.

The vendor publishes no junction to case figure, so the number cannot be computed from the document. It has to come from the mechanical drawing on the product page and from a first article temperature measurement. That is a slower route than reading a curve, and it is the only honest one where the document is this thin.

At 40 per cent efficiency the dissipation is 125.3 W, which doubles the demand again. A proposal built on the published floor has to carry that as a sensitivity rather than assume the typical will hold.

Why the gain floor drop matters more than the power step

Moving from the 43 dBm member to this one is 4 dB of output for 3 dB less gain, so the drive rises from 1.26 W to 3.98 W, a factor of 3.16 rather than 2. The driver stage that fed the twenty watt part is no longer adequate, and the chain behind it has to be re-planned from the exciter forward.

In a multi stage line amplifier that is usually the point where a second 28 V stage is added rather than a bigger single driver, because a 36 dBm driver built from the smaller members of the same band keeps one rail and one transistor family across the whole chassis.

The ladder makes that easy: 37, 40 and 43 dBm members all run on 28 V with a 12 dB floor, so a driver chain built from them is a matter of picking the output rung. Our RF power transistor cross reference page sets out how the four fields of rail, mode, band and power narrow a candidate list.

Running two of them instead of one hundred watt part

A balanced pair of these gives 100 W at the same band with 3 dB less gain per device and the same 28 V rail. The advantage is not only thermal: with a hybrid combiner the load presented to each device is set by the hybrid rather than by the antenna, so a 2:1 mismatch at the output appears as a smaller reflection at each drain.

The cost is the combiner, the extra board area and the matching between the two devices. At 4.4 to 5 GHz a 3 dB hybrid is a real component with its own loss, and the 0.3 to 0.5 dB it takes out of the chain has to be added to the link budget.

The alternative is the 50 dBm member on the same rail, which is one device with 3 dB more output and 1 dB less gain. Which route is cheaper depends on the volume and on whether the chassis is shared with other bands.

What to settle before a fifty watt build is quoted

The gate bias is not published and at four amperes of drain current a wrong bias point is destructive. The first article has to be a bias sweep against quiescent current with the drain current limited, and the operating point has to be recorded on the build sheet rather than left to the test operator.

The drain feed carries 3.98 A continuously. Choke, capacitor bank, ground return and connector rating are all first order at this current, and a feed inherited from a ten watt board will heat, sag and eventually fail.

The output has to be protected. At 70.8 V peak into a matched load, a 2:1 mismatch raises the voltage further, and the vendor publishes no load mismatch tolerance. An isolator or a circulator at the output is the ordinary answer. Our guide to choosing an RF amplifier covers the protection order for a stage at this level.

Questions buyers ask about HXN40050

Is this the same carrier as the twenty watt part. The band, the rail and the flatness rows are shared, so the family is presented as one band with several power rungs, but the documents do not publish the package outline in text, so the mechanical fit has to be checked against the drawing rather than assumed.

Can it be pulsed for more output. The part is published as continuous wave, and pulsing it does not raise the saturated output above the published floor. Pulse operation only helps the thermal side.

What happens above 50 dBm on this band. The next member runs on 32 V, so a 28 V chassis stops at this rung unless a second rail is added. That is a supply decision, not a transistor decision.

How is availability handled. Through the RF procurement route, with band, rail, mode and quantity named on the request and packing confirmed with the factory before a date is quoted.